0816 Produce Safety GFI draft

Standards for the Growing, Harvesting, Packing, and Holding of Produce for Human Consumption - Agricultural Water - FINAL RULE

0816 Produce Safety GFI draft

OMB: 0910-0816

Document [pdf]
Download: pdf | pdf
Contains Nonbinding Recommendations
Draft-Not for Implementation

Standards for the Growing, Harvesting,
Packing, and Holding of Produce for Human
Consumption: Guidance for Industry
Draft Guidance
This guidance is being distributed for comment purposes only.
Although you can comment on any guidance at any time (see 21 CFR 10.115(g)(5)), to
ensure that FDA considers your comment on this draft guidance before we begin work on the
final version of the guidance, submit either electronic or written comments on the draft
guidance within 180 days of publication in the Federal Register of the notice announcing the
availability of the draft guidance. Submit electronic comments to
https://www.regulations.gov. Submit written comments to Dockets Management Staff
(HFA-305), Food and Drug Administration, 5630 Fishers Lane, rm. 1061, Rockville, MD
20852. All comments should be identified with the docket number FDA-2018-D-3631 listed
in the notice of availability that publishes in the Federal Register.
For questions regarding this draft document contact the Center for Food Safety and Applied
Nutrition (CFSAN) at 240-402-1700.

U.S. Department of Health and Human Services
Food and Drug Administration
Center for Food Safety and Applied Nutrition
October 2018

Contains Nonbinding Recommendations
Draft-Not for Implementation

Standards for the Growing, Harvesting,
Packing, and Holding of Produce for Human
Consumption: Guidance for Industry1
This draft guidance, when finalized, will represent the current thinking of the Food and Drug
Administration's (FDA or we) on this topic. It does not establish any rights for any person and is
not binding on FDA or the public. You can use an alternative approach if it satisfies the
requirements of the applicable statutes and regulations. To discuss an alternative approach,
contact the FDA staff responsible for this guidance as listed on the title page.

Table of Contents
I.

Introduction ......................................................................................................................... 5

II.

Background ......................................................................................................................... 5
Chapter 1: General Provisions (Subpart A) ........................................................................... 7
1. Produce ........................................................................................................................... 9
2. Raw Agricultural Commodity....................................................................................... 10
3. Covered Produce ........................................................................................................... 11
Rarely Consumed Raw ............................................................................................. 12
Personal Consumption and On-Farm Consumption ................................................. 13
Produce Eligible for Exemption by Commercial Processing that Adequately
Reduces the Presence of Microorganisms of Public Health Significance ........................ 13
4. Covered Farms .............................................................................................................. 14
$25,000 Threshold .................................................................................................... 15
Qualified Exemption ................................................................................................. 18
5. Covered Activities ........................................................................................................ 25
Chapter 2: Personnel Qualifications and Training (Subpart C) ........................................ 26
1. Evaluating Personnel’s Assigned Duties ...................................................................... 26
2. Qualifications Necessary to Perform Assigned Duties ................................................. 27
3. Training Frequency ....................................................................................................... 29
4. Easily Understandable Training .................................................................................... 30
5. Minimum Training Requirements................................................................................. 31
Food Hygiene and Food Safety................................................................................. 32
Health and Personal Hygiene .................................................................................... 33

1

This draft guidance has been prepared by the Office of Food Safety, Division of Produce Safety in the Center for
Food Safety and Applied Nutrition at the U.S. Food and Drug Administration.

1

Contains Nonbinding Recommendations
Draft-Not for Implementation
6.

7.
8.
9.

Standards in Subparts C through O........................................................................... 34
Additional Training for Persons Who Conduct Harvest Activities .............................. 35
Recognizing When Not to Harvest Covered Produce............................................... 36
Harvest Containers and Equipment .......................................................................... 36
Food Safety Training for a Supervisor or Responsible Party ....................................... 37
Supervision to Ensure Compliance ............................................................................... 38
Training Records ........................................................................................................... 38

Chapter 3: Health and Hygiene (Subpart D) ....................................................................... 39
1. Measures to Prevent Ill or Infected Persons from Contaminating Covered Produce ... 39
Understanding Applicable Health Conditions .......................................................... 40
Self-identification of Applicable Health Conditions ................................................ 41
Role of Supervisors in Identifying Applicable Health Conditions ........................... 42
Addressing Reports of Applicable Health Conditions .............................................. 43
Response to Potential Contamination of Covered Produce or Food Contact Surfaces
44
2. Hygienic Practices ........................................................................................................ 45
Personnel and Hygienic Practices ............................................................................. 46
Role of Supervisors in Ensuring Personnel Follow Hygienic Practices ................... 46
Required Hygienic Practices ..................................................................................... 47
3. Measures to Prevent Visitors from Contaminating Covered Produce and Food Contact
Surfaces ................................................................................................................................. 54
Visitor Awareness of Policies and Procedures ......................................................... 55
Toilet and Hand-Washing Facilities ......................................................................... 56
Chapter 4: Biological Soil Amendments of Animal Origin and Human Waste (Subpart
F) ............................................................................................................................................... 57
1. Determine Whether your Soil Amendment is a BSAAO ............................................. 59
2. Determine Whether your BSAAO is “Treated” or “Untreated” ................................... 61
Treated BSAAO ........................................................................................................ 61
Untreated BSAAO .................................................................................................... 61
3. Determine the Appropriate Treatment Process and Associated Microbial Standard for
your Treated BSAAO ........................................................................................................... 63
Validation Studies ..................................................................................................... 64
Processes to Treat BSAAOs ..................................................................................... 65
4. Determine How to Apply your BSAAO ....................................................................... 66
Untreated BSAAO .................................................................................................... 66
Treated BSAAO ........................................................................................................ 69
5. Determine the Requirements for Handling, Transporting, and Storing your BSAAO . 71
6. Determine What Records to Keep for your Treated BSAAO....................................... 72
Chapter 5: Domesticated and Wild Animals (Subpart I) ................................................... 74
1. Determining Reasonable Probability That Animals Will Contaminate Covered Produce
75
2. Assessing Relevant Areas for Evidence of Potential Contamination of Covered
Produce ................................................................................................................................. 77
Developing and Modifying Your Approach to Assessment ..................................... 77
Performing Monitoring Activities............................................................................. 79
2

Contains Nonbinding Recommendations
Draft-Not for Implementation
3. Evaluating Significant Evidence of Potential Contamination of Covered Produce by
Animals to Determine Whether Harvest Can Occur............................................................. 79
Chapter 6: Growing, Harvesting, Packing, and Holding Activities (Subpart K) ............. 82
1. Separation of Covered and Excluded Produce.............................................................. 82
2. Identifying and Not Harvesting Contaminated Covered Produce ................................ 85
3. Handling Harvested Covered Produce .......................................................................... 86
4. Dropped Covered Produce ............................................................................................ 87
5. Packaging Covered Produce ......................................................................................... 88
6. Food-Packing Material.................................................................................................. 89
Identifying Single-Use and Reusable Food-Packing Materials ................................ 90
Evaluating Your Practices and Food-Packing Materials .......................................... 91
Chapter 7: Equipment, Tools, Buildings, and Sanitation (Subpart L) .............................. 93
1. Equipment and Tools .................................................................................................... 93
Identifying Equipment and Tools Intended or Likely to Contact Covered Produce 94
Design, Construction, and Workmanship ................................................................. 94
Installation and Maintenance .................................................................................... 95
Storage ...................................................................................................................... 96
Inspection .................................................................................................................. 97
Examples ................................................................................................................... 99
Cleaning and Sanitizing Equipment and Tools ....................................................... 103
Transport Equipment .............................................................................................. 110
Instruments and Controls ........................................................................................ 110
2. Buildings ..................................................................................................................... 113
Size, Construction, and Design ............................................................................... 113
Preventing Contamination, Including Floors, Walls, and Ceilings ........................ 115
Drainage .................................................................................................................. 116
Pest Control............................................................................................................. 117
Domesticated Animals ............................................................................................ 118
3. Other Sanitation Measures .......................................................................................... 119
Animal Excreta and Litter from Domesticated Animals ........................................ 120
Toilet Facilities ....................................................................................................... 120
Hand-Washing Facilities ......................................................................................... 122
Sewage Systems ...................................................................................................... 125
Trash, Litter, and Waste .......................................................................................... 127
Plumbing ................................................................................................................. 129
4. Records ....................................................................................................................... 130
Chapter 8: Records (Subpart O) ......................................................................................... 131
1. General Requirements for all Records ........................................................................ 131
Farm Name and Location........................................................................................ 132
Location of Growing or Activity Area.................................................................... 132
Adequate Description of Covered Produce............................................................. 133
Actual Values and Observations ............................................................................. 133
Created when Activity is Performed or Observed .................................................. 133
Date and Time ......................................................................................................... 133
Accurate, Legible, and Indelible ............................................................................. 134
3

Contains Nonbinding Recommendations
Draft-Not for Implementation

2.
3.
4.
5.
6.
7.

Dated, and Signed or Initialed by the Person Who Performed the Activity ........... 134
Review by a Supervisor or Responsible Party ........................................................ 134
Records Storage .......................................................................................................... 136
Use of Existing Records.............................................................................................. 136
Records Retention ....................................................................................................... 137
Records Format ........................................................................................................... 137
Records Disclosure ..................................................................................................... 138
Specific Records Requirements .................................................................................. 138

Chapter 9: Variances (Subpart P) ....................................................................................... 139
1. Entities Eligible to Submit a Variance Request .......................................................... 139
2. Grounds for a Variance ............................................................................................... 139
3. Information to Support a Request for a Variance ....................................................... 140
4. Process for Requesting a Variance ............................................................................. 141
III.

References ....................................................................................................................... 142

4

Contains Nonbinding Recommendations
Draft-Not for Implementation

I.

Introduction

In the Federal Register of November 27, 2015, we published a final rule titled “Standards for the
Growing, Harvesting, Packing, and Holding of Produce for Human Consumption” (80 FR
74353) (Produce Safety Rule). The Produce Safety Rule established science-based minimum
standards for the safe growing, harvesting, packing, and holding of produce grown for human
consumption and is part of our implementation of the FDA Food Safety Modernization Act
(FSMA). This draft guidance is intended to help the owner, operator, or agent in charge of a
covered farm (i.e., “you”) to comply with the requirements of the Produce Safety Rule.
FDA's guidance documents, including this draft guidance, do not establish legally enforceable
responsibilities. Instead, guidances describe our current thinking on a topic and should be
viewed only as recommendations, unless specific regulatory or statutory requirements are cited.
The use of the word should in FDA guidances means that something is suggested or
recommended, but not required.

II.

Background

Produce is usually grown outdoors in soil, with influences from weather and other environmental
factors, and often does not receive treatment after harvesting that adequately removes pathogens
that can cause human illness (referred to in this draft guidance as microorganisms of public
health significance). Therefore, we place emphasis on preventive measures throughout growing,
harvesting, packing, and holding produce to reduce the incidence of contamination of produce
that can lead to foodborne illness.
The Produce Safety Rule established science-based minimum standards for the safe growing,
harvesting, packing, and holding of produce grown for human consumption. The rule requires
covered farms to take appropriate measures to minimize the risk of serious adverse health
consequences or death from the use of, or exposure to, covered produce, including those
measures reasonably necessary to prevent the introduction of known or reasonably foreseeable
hazards into covered produce, and to provide reasonable assurances that the produce is not
adulterated under section 402 of the Federal Food, Drug, and Cosmetic Act (FD&C Act). (21
CFR 112.11). Requirements of the rule focus on major routes of contamination, including: health
and hygiene; agricultural water; biological soil amendments of animal origin; domesticated and
wild animals; equipment, tools, buildings and sanitation; and related topics that include
personnel qualifications and training; growing, harvesting, packing, and holding activities; and
sprouts.
This draft guidance relates to compliance and implementation of the following subparts of the
Produce Safety Rule:
•
•
•
•
•

Subpart A–General Provisions;
Subpart C–Personnel Qualifications and Training;
Subpart D–Health and Hygiene;
Subpart F–Biological Soil Amendments of Animal Origin and Human Waste;
Subpart I–Domesticated and Wild Animals;
5

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•
•

Subpart K–Growing, Harvesting, Packing, and Holding Activities;
Subpart L–Equipment, Tools, Buildings, and Sanitation;
Subpart O–Records; and
Subpart P–Variances.

In the Federal Register of January 23, 2017, we published a notification of availability of a draft
guidance for industry titled, “Compliance with and Recommendations for Implementation of the
Standards for the Growing, Harvesting, Packing, and Holding of Produce for Human
Consumption for Sprout Operations: Guidance for Industry” (82 FR 7751), which focuses on the
portion of the Produce Safety Rule (subpart M) that deals with sprouts. Sprout operations should
note that this draft guidance addresses aspects of the Produce Safety Rule to which sprout
operations may also be subject.
At this time, we are not issuing draft guidance for the following: subpart Q–Compliance and
Enforcement; and subpart R–Withdrawal of Qualified Exemption. In the future, we may issue
additional draft guidance addressing subpart B–General Requirements related to alternatives, and
subpart E–Agricultural Water.
This draft guidance provides our current thinking and recommendations to help you comply with
the minimum standards of other subparts of the Produce Safety Rule. In some places, we refer
directly to specific requirements from the Produce Safety Rule, which we cite for reference. We
also provide recommendations, examples, clarification, and information to help you develop
your own procedures, processes, and practices, because the Produce Safety Rule requirements
generally include enough flexibility for you to put them in place in a way that best fits your
operations. In many instances, there may be several different approaches that all result in
compliance with the requirements of the Produce Safety Rule. In some cases, we provide
examples to illustrate and describe potential ways to meet the requirements of the Produce Safety
Rule. Note that we cannot, nor have we attempted to, describe every possible scenario and
solution.

6

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 1:
General Provisions (Subpart A)
This chapter addresses the requirements of Produce Safety Rule Subpart A–General Provisions,
which will help you to determine the applicability of the Produce Safety Rule to your farm and
your produce. The Produce Safety Rule applies equally to covered produce grown domestically
and covered produce imported or offered for import into any state or territory of the United
States, the District of Columbia, or the Commonwealth of Puerto Rico. (21 CFR 112.1(a)). In
other words, covered produce grown internationally and imported is subject to applicable
provisions of the Produce Safety Rule.
Generally, the Produce Safety Rule applies when three conditions are present: covered produce,
covered farm, and covered activity. If you are a covered farm, you must comply with all
applicable requirements of the Produce Safety Rule when conducting a covered activity on
covered produce. (21 CFR 112.4(a)).
This chapter is divided into 5 sections:
•
•
•
•
•

Produce;
Raw agricultural commodity;
Covered produce;
Covered farms; and
Covered activities.

This chapter will discuss each of these terms in sequence, and we recommend that you consider
them in the order in which they are presented. Each section is intended to help you determine
which provisions of the Produce Safety Rule, if any, apply to you and the food you produce.
In this chapter, we also discuss:
•
•
•
•

the threshold for farms not covered by the Produce Safety Rule (average annual value of
produce sold during the previous 3-year period of $25,000 or less);
produce that is rarely consumed raw and therefore not covered by the Produce Safety
Rule;
farms eligible for a qualified exemption; and
produce that is eligible for an exemption because it receives commercial processing that
adequately reduces the presence of microorganisms of public health significance.

The following is a figure to assist you in determining which provisions of the Produce Safety
Rule, if any, apply to you and the food you produce.

7

Contains Nonbinding Recommendations
Draft-Not for Implementation
Figure 1a. Standards for Produce Safety: Coverage and Exemptions

8

Contains Nonbinding Recommendations
Draft-Not for Implementation

1. Produce
In determining whether the Produce Safety Rule applies to your farm and the food you produce
on your farm, you should first consider whether the food is “produce.” Under the Produce Safety
Rule, “produce” generally means any fruit or vegetable, and includes mushrooms, sprouts,
peanuts, tree nuts, and herbs. (See the full definition of “produce” at 21 CFR 112.3). Fruit is
further defined as the edible reproductive body of a seed plant or tree nut (such as apple, orange,
or almond); stated another way, “fruit” means the harvestable or harvested part of a plant
developed from a flower. The Produce Safety Rule defines a vegetable as the edible part of an
herbaceous plant (such as cabbage or potato), or fleshy fruiting body of a fungus (such as white
button or shiitake mushroom) grown for an edible part; in other words, “vegetable” means the
harvestable or harvested part of any herbaceous plant or fungus whose fruit, fleshy fruiting
bodies, seeds, roots, tubers, bulbs, stems, leaves, or flower parts are used as food, and includes
mushrooms, sprouts, and herbs. (See 21 CFR 112.3).
Both “produce” and “covered produce” (see the section of this chapter titled “Covered Produce”)
refer to the “harvestable or harvested” part of the crop. That means that “produce” could include
components of the harvestable or harvested part of the plant that are not edible to humans. For
example, based on our current understanding of the crops and practices in the tree nut industry,
we consider the entire unit (nut or kernel, hull, and shell), the “harvestable or harvested part” of
the crop. The kernels that have been separated from the shell/hull (i.e., nut with no shell/hull)
would also be considered “produce.” The shells/hulls that have been separated from the kernel
would not be “produce” as defined in 21 CFR 112.3.
Once the harvestable or harvested part of the crop is present, “produce” is present. Ripeness or
maturity level does not matter. For example, unripe apples while not normally eaten at that point
in their production, are the harvestable and harvested part of the plant and are therefore
“produce,” including while they are still growing on the tree.
Produce that is not reasonably expected to be directed to a human food use is not subject to the
requirements of the Produce Safety Rule. For example, produce that is reasonably expected to
be used for biofuels, clothing, or household products is not subject to the Produce Safety Rule.
Produce that is reasonably expected to be used only as animal food is not subject to the
requirements of the Produce Safety Rule. Produce that is reasonably expected to be used only
for propagation of a crop (e.g., seeds, bulbs) is not subject to the requirements of part 112
(except to the extent the Produce Safety Rule addresses seed for sprouting). If you grow,
harvest, pack, or hold produce, some of which is reasonably expected to be directed to a human
food use and some of which is not reasonably expected to be directed to a human food use, you
could comply with the requirements of the Produce Safety Rule for all of the produce so that you
retain the option to direct all of the produce to a human food use.
There are many produce commodities, so we have included in this draft guidance examples in
addition to the list provided in 21 CFR 112.1(b)(1): ackee; aronia; arrowhead; arrowroot;
atemoya; butterbur; cactus; chipilin; crabapple; dragon fruit; fiddlehead; ginkgo nut; komatsuna;

9

Contains Nonbinding Recommendations
Draft-Not for Implementation
longan; loroco; lotus root; microgreens 2; persimmon; pomegranate; pomelo; ramp; salsify;
swamp cabbage; tamarillo; tea; ti plant; and ulluko. Edible flowers such as nasturtiums,
lavender, and squash blossoms are also “produce.”
“Produce” does not include food grains–meaning the small, hard fruits or seeds of arable crops,
or the crops bearing these fruits or seeds–that are primarily grown and processed for use as meal,
flour, baked goods, cereals, or oils rather than for direct consumption as small, hard fruits or
seeds (including cereal grains, pseudo cereals, oilseeds, and other plants used in the same
fashion). (21 CFR 112.3). Examples of food grains include barley, dent- or flint-corn, sorghum,
oats, rice, rye, wheat, amaranth, quinoa, buckwheat, and oilseeds (e.g., cotton seed, flax seed,
rapeseed, soybean, and sunflower seed).
Saps (e.g., agave, birch, maple, palm) do not fit the definition of “produce” and therefore are not
subject to the Produce Safety Rule. Algae (e.g., seaweed) is not produce and therefore also not
subject to the Produce Safety Rule.

2. Raw Agricultural Commodity
In determining whether the Produce Safety Rule applies to your farm and the food you produce
on your farm, you should next consider whether the food you produce is a raw agricultural
commodity. Only food that is both a raw agricultural commodity (“RAC”) and “produce” is
subject to the Produce Safety Rule. (See 21 CFR 112.1(a) and 112.2(a)(3)). RAC means any
food in its raw or natural state, including all fruits that are washed, colored, or otherwise treated
in their unpeeled natural form prior to marketing. (Section 201(r) of the FD&C Act (21 U.S.C.
321(r)); (21 CFR 112.3)).
RACs changed into “processed food” are no longer subject to the Produce Safety Rule in their
transformed state because they are no longer a RAC. It is important to understand this
distinction, which is not always apparent. Changing a RAC into a “processed food” involves
changing the general state of the commodity, sometimes referred to as transformation of the
RAC into a new or distinct commodity. Processed foods are not subject to the Produce Safety
Rule (See 21 CFR 112.2(a)(3)).
As noted earlier, the distinction between a RAC and a processed food is easily apparent in some
cases and not in others. Below are examples that help demonstrate the distinction.
Examples of activities that do not change a RAC into a processed food include:
•

Hydro-cooling;

2

Microgreens and sprouts are distinct commodities. Historically, the primary criterion FDA has used to distinguish
between the two product categories has been the growth stage of the leaves (Ref. 221). Sprouts are usually
harvested when the cotyledons (or seed leaves) are still un- or under-developed and true leaves have not begun to
emerge. In contrast, microgreens reach a later stage of growth, typically associated with the emergence of ‘‘true’’
leaves. Microgreens are also typically grown in soil or substrate and harvested above the soil or substrate line.
Because microgreens are not sprouts, they are not subject to the requirements in subpart M. However, microgreens
are considered “covered produce’’ for the purposes of this rule and, unless exempt or excluded under the provisions
in subpart A, microgreens and microgreen farms are subject to all other subparts of part 112. (See 80 FR 74353 at
74497 (Comment/Response 363)).

10

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•
•

Refrigeration;
Removal of leaves, stems, and husks;
Washing; and
Activities designed only to isolate or separate the commodity from foreign objects or
other parts of the plant.

Examples of activities that change a RAC into a processed food include:
•
•
•
•
•
•

Chopping;
Cooking;
Cutting;
Homogenization;
Irradiation; and
Pasteurization.

The following are more specific examples of the distinction between RACs and processed foods:
•
•
•
•

Whole heads of lettuce are a RAC; however, they are no longer a RAC once they are
chopped into smaller pieces; chopped lettuce is a processed food;
Whole walnuts are a RAC; however, they are no longer RACs once they are ground into
walnut butter; walnut butter is a processed food;
Fresh oranges are a RAC; however, they are no longer RACs once they are processed to
produce orange juice; orange juice is a processed food; and
Fresh papayas are a RAC; however, they are no longer a RAC once they are irradiated,
irradiated papayas are a processed food.

The fact that a particular RAC will be made into processed food does not necessarily mean that
the RAC is exempt from the Produce Safety Rule. The Produce Safety Rule applies only during
the time that the food is a RAC.

3. Covered Produce
Not all produce that is also a raw agricultural commodity is subject to the provisions of the
Produce Safety Rule. In determining whether the Produce Safety Rule applies to your farm and
the food you produce on your farm, you should next consider whether your produce is “covered
produce.” “Covered produce” is produce that is a raw agricultural commodity and within the
scope of the Produce Safety Rule. (21 CFR 112.1). “Produce” is subject to the Produce Safety
Rule unless it is “not covered” or is eligible for an exemption.
Produce that is not covered under the Produce Safety Rule includes that which is:
•
•
•

Rarely consumed raw;
Produced for personal or on-farm consumption; or
Not a raw agricultural commodity.

Additionally, some produce is eligible for exemption from the Produce Safety Rule under 21
CFR 112.2(b) (i.e., commercial processing that adequately reduces the presence of
11

Contains Nonbinding Recommendations
Draft-Not for Implementation
microorganisms of public health significance: “the commercial processing exemption”). We
discuss these concepts in the subsequent subsections, except for “Raw Agricultural
Commodities” which was covered in a previous section.
Rarely Consumed Raw
“Rarely consumed raw” (RCR) produce includes those commodities that FDA determined are
almost always eaten only after being cooked. The following is a complete list of the produce
designated as “rarely consumed raw” in 21 CFR 112.2(a)(1), and thus not subject to the
provisions of the Produce Safety Rule:
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•

Asparagus;
Black, great Northern, kidney, lima, navy, and pinto beans;
Garden beet (root and top);
Sugar beet;
Cashew;
Sour cherry;
Chickpea;
Cocoa bean;
Coffee bean;
Collard;
Sweet corn;
Cranberry;
Date;
Dill (seed and weed);
Eggplant;
Fig;
Ginger;
Hazelnut;
Horseradish;
Lentil;
Okra;
Peanut;
Pecan;
Peppermint;
Potato;
Pumpkin;
Winter squash;
Sweet potato; and
Water chestnut. (21 CFR 112.2(a)(1)).

For your produce to be RCR, you do not have to have knowledge or confirmation of the cooking
process the produce receives, or where, how, or by whom it is performed.

12

Contains Nonbinding Recommendations
Draft-Not for Implementation
Personal Consumption and On-Farm Consumption
Produce that is produced by an individual for personal consumption, or produced for
consumption on the farm on which it was produced or on another farm under the same
management, is not subject to the Produce Safety Rule. (21 CFR 112.2(a)(2)). For example, if a
covered farm grows covered produce, and separately grows produce for personal consumption in
an owner’s personal home garden that is located on the farm’s property, the produce for personal
consumption would not be covered by the Produce Safety Rule.
Produce Eligible for Exemption by Commercial Processing that Adequately
Reduces the Presence of Microorganisms of Public Health Significance
Produce that receives commercial processing that adequately reduces the presence of
microorganisms of public health significance is eligible for exemption from most provisions of
the Produce Safety Rule (commercial processing exemption). To qualify for this exemption,
your produce must meet all of the conditions in 21 CFR 112.2(b). (21 CFR 112.2(b)). We
discuss each of these conditions in the following subsections:
•
•
•

Commercial processing;
Disclosure accompanying produce and affiliated records; and
Written assurances from your customers and affiliated records.

Subpart A—General Provisions, and subpart Q—Compliance and Enforcement, of the Produce
Safety Rule continue to apply to you and your exempt produce even if this commercial
processing exemption applies.
Commercial Processing
It is important to note that the commercial processing exemption is applicable only to the
produce that will receive commercial processing that adequately reduces the presence of
microorganisms of public health significance. Examples of such commercial processing
includes: processing in accordance with the requirements of the Low Acid Canned Foods
Regulation (21 CFR part 113), the Acidified Foods Regulation (21 CFR part 114), and the Juice
HACCP Regulation (21 CFR part 120); treating with a validated process to eliminate sporeforming microorganisms (such as processing to produce tomato paste or shelf-stable tomatoes);
and processing such as refining, distilling, or otherwise manufacturing/processing produce into
products such as sugar, oil, spirits, wine, beer, or similar products. Freezing processes and
washing (such as in a flume or dump tank) are commercial processes that generally do not
significantly reduce the presence of microorganisms (Ref. 3) (Ref. 8) (Ref. 9) (Ref. 61) (Ref. 90).
In some cases, only a portion of a farm’s produce might be eligible for the commercial
processing exemption. For example, if you own or operate a covered farm that produces both
tomatoes that will be processed into tomato paste, and tomatoes that will be sold into the fresh
market (i.e., tomatoes that will not be processed into tomato paste), only the tomatoes that will be
processed into tomato paste are eligible for the commercial processing exemption under 21 CFR
112.2(b).

13

Contains Nonbinding Recommendations
Draft-Not for Implementation
Disclosure Accompanying Produce and Affiliated Records
For your otherwise covered produce to qualify for the commercial processing exemption, you
must disclose, in documents accompanying the produce, in accordance with the practice of the
trade, that the food is “not processed to adequately reduce the presence of microorganisms of
public health significance.” (21 CFR 112.2(b)(2)). Visual examination of the food might not
readily reveal whether commercial processing has already been applied, so providing the
disclosure through documentation or labeling helps to inform an entity in the supply chain that
such a control has not yet been applied.
The requirements for the disclosure statement specify that the disclosure must be made in
“documents accompanying the produce, in accordance with the practice of the trade.” (21 CFR
112.2(b)(2); See 21 CFR 112.2(b)(3)(ii)(A) and 112.2(b)(3)(ii)(B)(2)). This allows for the
disclosure statement to be provided using a wide variety of documents that accompany the food,
such as labels, labeling, bills of lading, freight bills, shipment-specific certificates of analysis,
and other documents or papers associated with the shipment that food safety personnel for the
customer is likely to read. For purposes of the requirements of the disclosure statement, you
could, for example, use labeling that includes a disclosure statement, “not processed to
adequately reduce the presence of microorganisms of public health significance,” and then direct
the recipient to a website for additional information. However, referencing a website in a
document of the trade without including the disclosure statement in the document of the trade
would not satisfy the requirement of 21 CFR 112.2(b)(2).
You must maintain documentation of disclosures that you provide to your customers in
accordance with the Produce Safety Rule subpart O–Records. (21 CFR 112.2(b)(4)). You could
keep the necessary documentation in various forms; for example, you could keep a sample
disclosure and a ledger of entries of shipments including the disclosures, or copies of labels with
the disclosure for each shipment. We provide additional draft guidance on general records
requirements at Chapter 8: Subpart O–Records.
Written Assurance from your Customers and Affiliated Records
In the Federal Register of January 5, 2018 (83 FR 598), we published a notification of
availability of a guidance document titled “Policy Regarding Certain Entities Subject to the
Good Manufacturing Practice and Preventive Controls, Produce Safety, and/or Foreign Supplier
Verification Programs.” In that guidance document, we stated that we intend to exercise
enforcement discretion regarding the written assurance requirements of 21 CFR part 112 (the
Produce Safety Rule). We intend to exercise such discretion until we can complete a rulemaking
process to consider options for the assurance requirements.

4. Covered Farms
With the exception of entities associated with the written assurances described in part 3.c.iii
above, only “covered farms” are subject to the requirements of the Produce Safety Rule. 3
3

As noted above, we have stated that we intend to exercise enforcement discretion related to the written assurances
associated with the commercial processing exemption.

14

Contains Nonbinding Recommendations
Draft-Not for Implementation
“Covered farms” as described in 21 CFR 112.4 are subject to all applicable requirements of the
Produce Safety Rule.
Some farms are not covered farms because they are under the $25,000 threshold that we discuss
later in this section. Some farms are eligible for a qualified exemption under 21 CFR 112.5 (21
CFR 112.4(b)), which limits the provisions to which they are subject. Qualified exemptions are
explained later in this section.
Covered farms include “farms” and “farm mixed-type facilities” as defined in 21 CFR 112.3. A
“farm mixed-type facility” is an establishment that is a farm, but that also conducts activities
outside the farm definition that require the establishment to be registered as a food facility under
section 415 of the FD&C Act. 4
Contract harvesters that only perform harvesting operations for a covered farm but do not sell the
produce are performing a covered activity on behalf of the covered farm. Those contract
harvesters would not be a covered farm; the farm for which they perform the harvesting would
be responsible for compliance with the requirements of the Produce Safety Rule with respect to
harvesting.
$25,000 Threshold
The Produce Safety Rule applies only to those farms or farm mixed-type facilities with more
than $25,000 in average annual value of produce sold during the previous 3-year period. (See
21 CFR 112.4(a)). To calculate whether your farm is above or below the $25,000 threshold:
•

Calculate the average annual monetary value of your gross produce sales;
o Determine which years’ sales need to be considered:
 For example, if 2018 is the applicable calendar year (i.e., for the year you
seek to calculate whether your farm is above or below the $25,000
threshold), you would need to calculate the average annual value of gross
sales for produce that you sold in 2017, 2016, and 2015.
o Include:
 All produce sold, not just covered produce–see the section of this chapter
titled “Produce”;
 Produce you purchased or otherwise obtained from another entity and then
resold to your customers;
 Produce you sold at farmer’s markets, to grocery stores, directly to
consumers, or online;

4

Section 415 of the FD&C Act requires that any facility engaged in manufacturing, processing, packing, or holding
food for consumption in the United States be registered with the Food and Drug Administration. The term “facility”
includes any factory, warehouse, or establishment (including a factory, warehouse, or establishment of an importer)
that manufactures, processes, packs, or holds food. Such term does not include: farms; restaurants; other retail food
establishments; nonprofit food establishments in which food is prepared for or served directly to the consumer; or
fishing vessels (except such vessels engaged in processing as defined in 21 CFR 123.3(k)).

15

Contains Nonbinding Recommendations
Draft-Not for Implementation


•

Produce sold by a third party on your behalf (such as when a cooperative
that takes possession of your produce without taking ownership sells your
produce and returns the proceeds to you after the sale); and
 Retail sales, wholesale sales, intrastate sales, and interstate sales
(including produce offered for import to the U.S. or exported from the
U.S.).
o Do not include:
 Produce for which you did not receive payment of money or anything else
of value in exchange for the produce (e.g., produce held without sale or
produce donated or given away);
 The value of produce from other entities when a third party sells produce
on your behalf along with produce from other entities (for example, if a
cooperative sells your produce along with produce for other farms does
not take ownership of your produce and returns the proceeds to you after
the sale, you should count only the proceeds from your produce, not any
proceeds from the sale of produce for other entities).
Adjust the baseline for inflation.
o Use a baseline year of 2011 (in other words, $25,000 in 2011).
 The U.S. Bureau of Economic Analysis provides the federal calculation
for inflation adjustments.
 We provide and intend to update the current adjusted dollar value for the
baseline on our Website
(https://www.fda.gov/food/guidanceregulation/fsma/ucm554484.htm) as
well.
o Using a baseline year of 2011, $25,000, adjusted for inflation, is $26,608 for
2015, $26,956 for 2016, and $27,433 for 2017, and the average 3-year value is
$26,999 for 2015-2017 (all figures obtained from the FDA website).

If your average annual value of produce sold during the previous 3-year period is $25,000 or
less, adjusted for inflation with a baseline year of 2011, then your farm is not subject to the
requirements of the Produce Safety Rule; you could find it useful to perform the calculation as
soon as possible in a given calendar year.
There may be circumstances where a farm does not have 3 calendar years of records, such as for
new farms. It would be reasonable for the farm to rely on a projected estimate of revenue (or
market value) when it begins operations. We would evaluate the credibility of the projection
considering factors such as the farm’s number of employees. After the farm has records for one
or two preceding calendar years, it would be reasonable for the farm to make the calculation
based on records it has (i.e., for one or two preceding calendar years) and we will accept records
for the preceding one or two years as adequate in these circumstances.
Following are examples to illustrate how these calculations should be performed:

16

Contains Nonbinding Recommendations
Draft-Not for Implementation
Example 1a.
•

•
•

•

•
•
•

A farm is performing a calculation in 2018 to determine whether it meets the $25,000
threshold. The farm would use its sales data for the preceding three years: 2015, 2016,
and 2017. In those years, the farm’s sales consisted of:
o 2015: $100,000 in live cattle; $50,000 in soybeans; $20,000 in tomatoes; $1000
in asparagus;
o 2016: $150,000 in live cattle; $25,000 in soybeans; $40,000 in tomatoes; $1500
in asparagus;
o 2017: $150,000 in live cattle; $60,000 in dent-corn; $10,000 in tomatoes; $1000
in asparagus;
The live cattle, soybeans, and dent-corn are not produce 5 (see the section of this chapter
titled “Produce” for information on this topic), so sales of these commodities are not
included in the calculations;
The farm sells the tomatoes and asparagus to retail customers through its farm stand
and sells some tomatoes to another farmer, who then sells them to a wholesaler. While
asparagus is not covered produce (because it is rarely consumed raw), both asparagus
and tomatoes are produce, so sales of these commodities are included in the
calculations. Retail and wholesale sales count toward the $25,000 threshold, so all of
the farm’s tomato and asparagus sales are included in the calculations;
Total produce sales for each year to be included in the calculations are:
o 2015: $21,000;
o 2016: $41,500;
o 2017: $11,000;
The three-year average of produce sales is the sum of $21,000 + $41,500 + $11,000,
divided by 3 = $24,500;
The 2015-2017 three-year average of $25,000 adjusted for inflation (obtained from the
FDA website) is $26,999;
$24,500 is less than $26,999, so the farm is not subject to the Produce Safety Rule.

Example 1b.
•

•

A new farm began operations in 2016 and is performing a calculation in 2018 to
determine whether it meets the $25,000 threshold. The farm would use its sales data
based on the records it has, in this example: 2016 and 2017. In those years, the farm’s
sales consisted of:
o 2016: $13,000 in spinach; $5,000 in kale;
o 2017: $20,000 in spinach; $10,000 in kale; $5,000 in basil;
The farm sells the spinach, kale, and basil to a wholesaler. Spinach, kale, and basil are
all produce (see the section of this chapter titled “Produce” for draft guidance on this
topic), so sales of these commodities are included in the calculations. The $20,000 in
spinach sales in 2017 included $10,000 in resale of spinach that the farm purchased

5

In these examples, the soybeans are grown for biofuels and are therefore considered food grains rather than
produce.

17

Contains Nonbinding Recommendations
Draft-Not for Implementation

•

•
•
•

from other farms in the area. Such sales count toward the $25,000 threshold, so all the
farm’s spinach sales are included in the calculations;
Total produce sales for each year to be included in the calculations are (the farm was
not operating in 2015, so this farm has only two years of sales to average):
o 2016: $18,000;
o 2017: $35,000;
The two-year average of produce sales is the sum of $18,000 + $35,000 = $53,000,
divided by 2 = $26,500;
The two-year average of $25,000 adjusted for inflation for 2016 and 2017 is $26,956 +
$27,433 = $54,389 divided by 2 = $27,195 (2016 and 2017 inflation-adjusted figures
obtained from the FDA website);
$26,500 is less than $27,195, so the farm is not subject to the Produce Safety Rule.
Qualified Exemption

If you exceed the $25,000 threshold, you could still determine that you are eligible for a qualified
exemption. Determination of a qualified exemption is based on all food 6 sales, not just produce
sales. Examples of food include livestock 7; meat; dairy products such as milk; hay; grains; and
wine; and other food (for humans or other animals).
A farm is eligible for a qualified exemption if it meets the requirements of 21 CFR 112.5:
1) the average annual monetary value of the food your farm sold directly to qualified endusers (see criteria section below) must be greater than that sold to all other buyers during the
same period; and
2) the average annual monetary value of all food your farm sold during the preceding 3year period must be less than $500,000, as adjusted for inflation. (See 21 CFR 112.5(a)).
There are examples below that demonstrate how to calculate the criteria for eligibility for a
qualified exemption.
If your farm is eligible for a qualified exemption for an applicable calendar year, then modified
requirements of the Produce Safety Rule apply (21 CFR 112.6, 112.7); therefore, you could find
it useful to perform the calculation as soon as possible in a given calendar year. Draft guidance
on modified requirements is provided in the section of this chapter titled “Modified
Requirements for a Farm with a Qualified Exemption.” You must also analyze your sales every
year to verify your continued eligibility for the exemption (21 CFR 112.7(b)).

6

Food is defined in 21 CFR 112.3. The qualified exemption is based on sales of all food rather than on produce
sales because the exemption is defined in the FSMA statute.
7
Livestock and meat are both food within the definition of “food” in 21 CFR 112.3. (See U.S. v. Tuente Livestock,
888 F. Supp. 1416 (S.D. Ohio 1995) (FDA may interpret the term “food” to “include live animals raised for food”)).
There are instances when live animals are sold for purposes other than for food, such as being sold as pets (e.g.,
dogs). Food held without sale (including live animals raised for food on a farm) need not be counted for purposes of
this calculation unless and until it is sold.

18

Contains Nonbinding Recommendations
Draft-Not for Implementation
Criteria for Eligibility for a Qualified Exemption
To be eligible for a qualified exemption in a given calendar year, you must meet both of the
criteria below. (21 CFR 112.5(a)).
A. Criterion 1: 3-Year Average Annual Food Sales Direct to Qualified
End Users is Greater than to All Other Buyers
During the 3-year period preceding the applicable calendar year, your farm’s average annual
monetary value of food (as defined in 21 CFR 112.3) sold directly to qualified end-users (as
defined in 21 CFR 112.3) must exceed the average annual monetary value of food sold to all
other buyers during that period in order to be eligible for a qualified exemption. (21 CFR
112.5(a)(1)).
A qualified end-user, with respect to food, is either:
(1) The consumer of the food (where the term consumer does not include a business);
• Consumers are qualified end-users, regardless of the consumer’s location
relative to the farm.
or
(2) A restaurant or retail food establishment (as those terms are defined in 21 CFR 1.227)
that is located in the same State or the same Indian reservation as the farm that produced
the food, or not more than 275 miles away from such farm.
• A restaurant is a facility that prepares and sells food directly to consumers for
immediate consumption. (See 21 CFR 1.227).
• A retail food establishment’s primary function is to sell food directly to
consumers. (See 21 CFR 1.227). Examples include roadside farm stands,
meal kit services, grocery stores, convenience stores, and farmer’s markets
that fit the definition.
A sale conducted online or through mail-order can be considered a sale to a qualified end-user if
the buyer is a consumer, or is a restaurant or retail food establishment that meets the location
requirements. For domestic farms, food sales to a restaurant or retail food establishment in a
neighboring country (e.g., Canada, Mexico, or the Bahamas) that is within 275 miles of the farm
represent sales to a qualified end-user. The same would also be true for a farm in Mexico selling
food to a restaurant or retail food establishment in the United States within 275 miles of the farm.
Criterion 1 involves comparing the value of food “sold directly” to qualified end-users to the
value of food sold via all other types of sales during the specified time period. For example,
direct sales to a restaurant or retail food establishment at an auction, where the auction serves as
a venue for the sale of your produce but does not purchase the produce, can be counted as a sale
to a qualified end-user if the restaurant or retail food establishment meets the location
requirements.

19

Contains Nonbinding Recommendations
Draft-Not for Implementation
The following are examples to illustrate how the calculations for criterion 1 should be
performed:
Example 1c (note that this example is a modification of Example 1a above, with some of the
factors changed for illustrative purposes).
•

•
•

•

•

•
•
•

A farm is performing a calculation in 2018 to determine whether it meets criterion 1.
The farm would use its sales data for the preceding three years: 2015, 2016, and 2017.
In those years the farm’s sales consisted of:
o 2015: $100,000 in live cattle; $50,000 in soybeans; $30,000 in tomatoes; $1000
in asparagus;
o 2016: $150,000 in live cattle; $25,000 in soybeans; $40,000 in tomatoes; $1500
in asparagus;
o 2017: $150,000 in live cattle; $60,000 in dent-corn; $40,000 in tomatoes; $1000
in asparagus;
The live cattle, soybeans, dent-corn, tomatoes, and asparagus are all food, as described
above, so sales of these commodities are included in the calculations;
The farm sells the asparagus and some tomatoes to retail customers through its farm
stand and also sells some tomatoes to another farmer, who then sells them to a
wholesaler. Customers of the farm stand include consumers and the owners of three
restaurants located in towns in the same and an adjoining state that are located between
two and 15 miles from the farm. Both consumers and the restaurants to which the farm
sells meet the definition of “qualified end user,” as described above. The farm sells the
live cattle, soybeans, and dent-corn to a wholesaler;
Sales of tomatoes are further divided as follows:
o 2015: $20,000 to qualified end users; $10,000 to wholesaler;
o 2016: $20,000 to qualified end users; $20,000 to wholesaler;
o 2017: $20,000 to qualified end users; $20,000 to wholesaler;
To facilitate the calculation for criterion 1, the sales data can be displayed as follows:
o 2015: $21,000 to qualified end users ($20,000 tomatoes + $1000 asparagus);
$160,000 to other buyers ($10,000 tomatoes + $100,000 live cattle + $50,000
soybeans);
o 2016: $21,500 to qualified end users ($20,000 tomatoes + $1500 asparagus);
$195,000 to other buyers ($20,000 tomatoes + $150,000 cattle + $25,000
soybeans);
o 2017: $21,000 to qualified end users ($20,000 tomatoes + $1000 asparagus);
$230,000 to other buyers ($20,000 tomatoes + $150,000 live cattle + $60,000
dent-corn);
The three-year average of food sold to qualified end users is the sum of $21,000 +
$21,500 + $21,000, divided by 3 = $21,167;
The three-year average of food sold to other buyers is the sum of $160,000 + $195,000
+ $230,000, divided by 3 = $195,000;
$21,167 does not exceed $195,000, so the farm does not qualify for a qualified
exemption.

20

Contains Nonbinding Recommendations
Draft-Not for Implementation
Example 1d (note that this example is a modification of Example 1b above, with some of the
factors changed for illustrative purposes).
•

•

•

•
•
•
•

A new farm is performing a calculation in 2018 to determine whether it meets criterion
1. The farm would use its sales data based on the records it has, in this example: 2016,
and 2017. In those years, the farm’s sales consisted of:
o 2016: $40,000 in spinach; $15,000 in kale;
o 2017: $75,000 in spinach; $12,000 in kale; $10,000 in basil;
The farm sells the spinach, kale, and basil at its farm stand and through two regional
produce auctions. Spinach, kale, and basil are all food as discussed above, so sales of
these commodities are included in the calculations. All the customers of the farm stand
are consumers and are, therefore, qualified end users. Sales through the auctions are
direct to the customer; that is, the auctions do not take ownership of the food and then
resell to the buyer. Some of the buyers at the auctions are restaurants or retail grocers
and some are wholesalers. Most of the restaurants and retail grocers meet the criteria
for qualified end user (i.e., located within the same state or not more than 275 miles
from the farm), but some do not;
Sales of food are further divided as follows:
o 2016: $25,000 at farm stand (to consumers); $20,000 at auctions to qualified
end users; $10,000 at auctions to other buyers;
o 2017: $30,000 at farm stand (to consumers); $30,000 at auctions to qualified
end users; $37,000 at auctions to other buyers;
To facilitate the calculation for criteria 1, the sales data can be displayed as follows:
o 2016: $45,000 to qualified end users; $10,000 to other buyers;
o 2017: $60,000 to qualified end users; $37,000 to other buyers;
The average of food sold to qualified end users is the sum of $45,000 + $60,000,
divided by 2 = $52,500;
The average of food sold to other buyers is the sum of $10,000 + $52,500, divided by 2
= $23,500;
$35,000 exceeds $23,500, so the farm meets criterion 1 for a qualified exemption. The
farm would then need to determine whether it meets criterion 2.
B. Criterion 2: Less than $500,000 in 3-Year Average Annual Food
Sales

In order to be eligible for a qualified exemption, your farm also must satisfy the requirement in
21 CFR 112.5(a)(2). Under that subsection, your farm’s average annual monetary value of all
food (as defined in 21 CFR 112.3) sold during the 3-year period preceding the applicable
calendar year must be less than $500,000, adjusted for inflation. (21 CFR 112.5(a)(2)). The
applicable calendar year for calculating the adjustment for inflation is 2011. (21 CFR 112.5(b)).
Criterion 2 is based on the value of all food “sold.” To determine whether your farm’s average
annual value of food sold is below (i.e., less than) the $500,000 threshold:

21

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

Calculate the average annual monetary value of your gross food sales during the three–
year period preceding the applicable calendar year (i.e., for the year you seek to calculate
whether your farm is eligible for the qualified exemption):
o Determine which years’ sales need to be considered:
 For example, if 2018 is the applicable calendar year, calculate the average
amount of gross sales for all food that you sold in 2015, 2016, and 2017.
o Include:
 All food sales, not just produce;
 Food that you purchased or otherwise obtained from another entity and
then resold to your customers;
 Food that you sold at farmer’s markets, to grocery stores, directly to
consumers, or online;
 Food sold by a third party on your behalf; and
 Retail sales, wholesale sales, interstate sales (including produce offered
for import to the U.S. or exported from the U.S.), and intrastate sales.
o Do not include:
 Food held without sale (including live animals raised for food on your
farm); or
 Food for which there is no payment of money or anything else of value
received in exchange for the food (i.e., produce donated or given away).
Adjust the baseline for inflation:
o Use a baseline year of 2011 (in other words, $500,000 in 2011).
 The U.S. Bureau of Economic Analysis provides the federal calculation
for inflation adjustments.
 We provide and intend to update the current adjusted dollar value on our
website
(https://www.fda.gov/food/guidanceregulation/fsma/ucm554484.htm) as
well.
o Using a baseline year of 2011, $500,000, adjusted for inflation is $532,170 for
2015, $539,121 for 2016, and $548,654 for 2017 and the average 3-year value
adjusted for inflation for 2015-2017 is $539,982.

•

If the average annual value during the previous 3-year period is equal to or less than $500,000,
adjusted for inflation, with a baseline year of 2011, criterion 2 is satisfied. You could find it
useful to perform the calculation as early as possible in a given calendar year.
The following are continuations of the above examples, to illustrate how the calculations for
criterion 2 should be performed:
Example 1c, continued (note it is included for illustrative purposes only; since this farm already
determined that they do not meet criterion 1 for a qualified exemption, there would be no
practical need for performing a calculation for criterion 2).
•

A farm is performing a calculation in 2018 to determine whether it meets criterion 2.
The farm would use its sales data for the preceding three years: 2015, 2016, and 2017.
In those years, the farm’s sales consisted of:
22

Contains Nonbinding Recommendations
Draft-Not for Implementation

•

•
•
•

o 2015: $100,000 in live cattle; $50,000 in soybeans; $30,000 in tomatoes; $1000
in asparagus;
o 2016: $150,000 in live cattle; $25,000 in soybeans; $40,000 in tomatoes; $1500
in asparagus;
o 2017: $150,000 in live cattle; $60,000 in dent-corn; $40,000 in tomatoes; $1000
in asparagus;
The live cattle, soybeans, dent-corn, tomatoes, and asparagus are all food, as described
above, so sales of these commodities are included in the calculations. Annual sales of
food total:
o 2015: $181,000;
o 2016: $216,500;
o 2017: $251,000;
The three-year average of food sold is the sum of $181,000 + $216,500 + $251,000,
divided by 3 = $216,167;
The average three-year value adjusted for inflation (obtained from the FDA website) is
$539,982;
$216,167 is less than $539,982, so the farm meets criterion 2 for a qualified exemption.

Example 1d, continued.
•

•

•
•
•

A farm is performing a calculation in 2018 to determine whether it meets criterion 2.
The farm would use its sales data based on the records it has, in this example:2016, and
2017. In those years, the farm’s sales consisted of:
o 2016: $40,000 in spinach; $15,000 in kale;
o 2017: $75,000 in spinach; $12,000 in kale; $10,000 in basil;
Spinach, kale, and basil are all food as discussed above, so sales of these commodities
are included in the calculations. Annual sales of food total:
o 2016: $55,000;
o 2017: $97,000;
The average of food sold is the sum of $55,000 + $97,000, divided by 2 = $76,000;
The baseline value adjusted for inflation for 2016 is $539,121 and for 2017 is $548,654
(obtained from the FDA website) and the two-year average is $543,888;
$76,000 is less than $543,888, so the farm meets criterion 2 for a qualified exemption.
Since this farm also met criterion 1 for a qualified exemption as illustrated above, the
farm would qualify for a qualified exemption.
Records

If you are eligible for a qualified exemption under 21 CFR 112.5, you must establish and keep
adequate records necessary to demonstrate that you satisfy the criteria for a qualified exemption,
including a written record reflecting that you have performed an annual review and verification
that you continue to meet those criteria. (21 CFR 112.7(b)).
Receipts or ledgers of sales to your customers that show the value of the sale of food items and
the location of the customer (for any customers that are restaurants or retail food establishments)
are examples of records that could be used to document your eligibility for a qualified
23

Contains Nonbinding Recommendations
Draft-Not for Implementation
exemption. In certain situations, such as a farmer’s market, if all sales are to consumers, keeping
track of daily sales rather than individual sales could be sufficient. If you already keep records
for another purpose, you may use those records to document your eligibility for a qualified
exemption if they also meet all applicable requirements of the Produce Safety Rule. Records you
establish and keep to demonstrate your farm is eligible for a qualified exemption must meet the
requirements of 21 CFR 112.7.
To document your annual review and verification of eligibility, you should make and keep a
report for each calendar year that includes the following information:
(1) Your total annual value of sales of food for each of the preceding three calendar years
(e.g., $181,00, $216,500, $251,000 for Example 1c; and $0, $55,000, $97,000 for
Example 1d);
(2) The average of the three values from item (1) (e.g., $216,167 for Example 1c; and
$50,677 for Example 1d);
(3) The inflation-adjusted value of $500,000, where the baseline year is 2011, using the
applicable calendar year adjustment value (e.g., $539,982 for Example 1c and 1d).
This value should be higher than the value in item (2) for you to be eligible for the
qualified exemption;
(4) Your total annual value of sales of food to qualified end-users for each of the
preceding three calendar years (e.g., $21,000, $21,500, $21,000 for Example 1c; and
$0, $45,000, $60,000 for Example 1d);
(5) The average of the three values from item (4) (e.g., $21,167 for Example 1c; and
$35,000 for Example 1d);
(6) Your total annual value of sales of food for each of the preceding three years to
entities other than qualified end users (e.g., $160,000, $195,000, $230,000 for
Example 1c; and $0, $10,000, $37,000 for Example 1d);
(7) The average of the three values from item (6) (e.g., $195,000 for Example 1c; and
$15,667 for Example 1d). This value should be lower than the value in item (5) for
you to be eligible for the qualified exemption); and
(8) A statement that, based on this information, you have concluded that you meet or
continue to meet the criteria for a qualified exemption.
Modified Requirements for a Farm with a Qualified Exemption
If your farm is eligible for a qualified exemption, you are subject to the following modified
requirements:
(1) When a food packaging label is required on food that would otherwise be covered
produce under the Federal Food, Drug, and Cosmetic Act or its implementing
regulations, you must include prominently and conspicuously on the food packaging
label the name and the complete business address of the farm where the produce was
grown (21 CFR 112.6(b)(1)); and
(2) When a food packaging label is not required on food that would otherwise be covered
produce under the Federal Food, Drug, and Cosmetic Act, you must prominently and
conspicuously display, at the point of purchase, the name and complete business
address of the farm where the produce was grown on a label, poster, sign, placard, or
24

Contains Nonbinding Recommendations
Draft-Not for Implementation
documents delivered contemporaneously with the produce in the normal course of
business, or, in the case of Internet sales, in an electronic notice (21 CFR
112.6(b)(2)).
The complete business address must include the street address or post office box, city, state, and
zip code for domestic farms, and comparable full address information for foreign farms. (21
CFR 112.6(b)(3)).
You are also subject to the requirements of the following Produce Safety Rule subparts:
•
•
•
•

Subpart A (General Requirements);
Subpart O (Records);
Subpart Q (Compliance and Enforcement); and
Subpart R (Withdrawal of Qualified Exemption).

5. Covered Activities
Covered farms subject to the Produce Safety Rule must comply with all applicable requirements
of the Produce Safety Rule when conducting a covered activity on covered produce. (21 CFR
112.4(a)). “Covered activity” is defined at 21 CFR 112.3 and means growing, harvesting,
packing, or holding covered produce, as well as certain other types of activities identified in the
definition. This means, for example, that if a covered farm grows, harvests, packs, or holds
covered produce, it is required to comply with all applicable provisions of the Produce Safety
Rule in the process of doing those things.
For example, for a farm that composts biological soil amendments of animal origin to use in
growing covered produce, the relevant provisions of the rule related to composting biological
soil amendments of animal origin apply. As another example, if a farm packs covered produce
on a table, the relevant provisions of the Produce Safety Rule related to cleaning and sanitizing
of the table apply.

25

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 2:
Personnel Qualifications and Training (Subpart C)
Personnel can introduce contamination while handling covered produce or food contact surfaces.
Some produce-related outbreaks and contamination events identified personnel health and
hygiene practices on the farm (Ref. 70) (Ref. 138) and produce handling and storage practices as
likely contributing factors to these events (Ref. 32) (Ref. 72). Furthermore, a study of foodrelated outbreaks found more than 800 instances where personnel practices were reported to be
instrumental in or contributory to the outbreak (Ref. 65).
All personnel should be qualified to perform their assigned duties, understand how their actions
impact food safety, and understand the regulatory requirements that apply to their assigned duties
(See 21 CFR 112.21(b) for specific requirements that apply to some personnel). Training helps
provide farm personnel, including supervisors and responsible parties, a knowledge base that
promotes safe food handling practices, and should ultimately reduce the likelihood of foodborne
illness attributable to food handling practices.
This chapter will help you:
•
•
•
•
•
•
•
•
•

Evaluate personnel’s assigned duties and identify personnel subject to the
qualifications and training requirements;
Evaluate whether personnel have the necessary qualifications to perform their
assigned duties;
Provide training at frequencies necessary to comply with Produce Safety Rule
requirements;
Determine how to provide easily understandable training;
Understand minimum training content for required training;
Understand additional training for persons who conduct harvest activities;
Understand training requirements for supervisors and responsible parties;
Understand requirements for supervision to ensure compliance; and
Determine required records for training.

Where applicable, we recommend periodically evaluating your relevant personnel, procedures,
processes, and practices to ensure that you consider the scope of your relevant activities or
operations, your personnel and their assigned duties, and any changes that occurred and how they
are affected by and relate to the requirements of the Produce Safety Rule. During such
evaluations, you should consider not only typical practices, but also those that occur infrequently
or due to unusual circumstances, to account for the breadth of personnel, procedures, processes,
and practices associated with a given activity.

1. Evaluating Personnel’s Assigned Duties
All personnel who handle covered produce or food contact surfaces, or those who are engaged in
the supervision thereof, are subject to specific requirements regarding qualifications and training.
(See 21 CFR 112.21). There are specific additional requirements for persons who conduct

26

Contains Nonbinding Recommendations
Draft-Not for Implementation
harvest activities for covered produce. (21 CFR 112.22). This includes full-time, permanent,
temporary, part-time, seasonal, contracted, and all other relevant personnel.
To identify your personnel subject to the qualifications and training requirements in subpart C,
you should review the assigned duties and observe the performance of the duties of all your
personnel, including supervisors. All personnel who handle covered produce or food contact
surfaces, or who are engaged in the supervision thereof, must:
•
•

receive adequate training (21 CFR 112.21(a)); and
have a combination of education, training, and experience necessary to perform their
assigned duties in a manner that ensures compliance with the Produce Safety Rule. (21
CFR 112.21(b)).

It is important that you consider the breadth of covered activities on your farm, and how they are
performed, to determine whether personnel performing each activity contact covered produce or
food contact surfaces. Examples of activities where personnel handle covered produce or food
contact surfaces include: harvesting covered produce by hand; sorting, grading, and packing
covered produce; handling food contact surfaces of containers used to distribute covered
produce; and cleaning and maintaining harvesting and packing equipment that directly contacts
covered produce. In some circumstances, activities such as receiving or shipping could also
involve contact with covered produce or food contact surfaces, depending on your procedures for
such activities. Other personnel could be assigned to duties that do not involve contact with
covered produce or food contact surfaces (e.g., removing trash, sweeping floors, maintaining
restrooms, maintaining or repairing non-food contact surfaces of equipment, pest control, or
operating forklifts and tractors). However, if such personnel are expected to handle covered
produce or food contact surfaces, even infrequently, or are engaged in the supervision thereof,
they must receive adequate training and have a combination of education, training, and
experience necessary to perform their assigned duties in a manner that ensures compliance with
the Produce Safety Rule because they are handling covered produce or food contact surfaces.
(See 21 CFR 112.21(a) and 21 CFR 112.21(b)).

2. Qualifications Necessary to Perform Assigned Duties
All personnel who handle covered produce or food contact surfaces, or who are engaged in the
supervision thereof, must have a combination of education, training, and experience necessary to
perform the person’s assigned duties in a manner that ensures compliance with the Produce
Safety Rule. (21 CFR 112.21(b)). You should evaluate the assigned duties of your personnel,
identify those who handle covered produce or food contact surfaces and their current level of
training, education, and experience, to determine whether they are qualified to perform their
assigned duties in a manner that ensures compliance with the Produce Safety Rule. When
assigning duties, you must ensure that the assigned personnel have the appropriate combination
of education, training, and experience to perform their duties, or that they receive any additional
education or training necessary to perform their duties. (See 21 CFR 112.22(b)). Depending on
the job duties, this could include training in combination with education, or experience.
An appropriate combination of education, training, and experience prepares these personnel to
conduct the assigned duties in a manner that aligns with the requirements of the Produce Safety
27

Contains Nonbinding Recommendations
Draft-Not for Implementation
Rule (such as the requirements described in subpart D–Health and Hygiene; subpart K–Growing,
Harvesting, Packing, and Holding Activities; and subpart L–Equipment, Tools, Buildings, and
Sanitation). These personnel should be able to apply their knowledge to perform their assigned
duties. For example, if you assign personnel to pack covered produce by hand, they should have,
and be able to apply, knowledge including that related to: health conditions that could result in
contamination of covered produce (e.g., their duty to report to a supervisor if they become ill
with, for example, diarrhea); the appropriate level of personal cleanliness for their assigned
duties; avoiding contact with animals other than working animals; proper hand-washing
procedures; using food-packing materials that are adequate for their intended use; proper
handling of harvested covered produce; and maintenance of food contact surfaces.
The extent of education, training, and experience necessary is likely to vary among your
personnel based on the level of responsibility and range of duties that you assign. Your
personnel could already possess valuable education and experience specific to particular
assigned duties, which you could consider when evaluating their assigned duties and
qualifications. However, some personnel could need additional training or education to ensure
they understand your food safety procedures based on the requirements of the Produce Safety
Rule. For example, you could assign one of your workers, who has worked on farms for a
decade and has a good understanding of horticultural practices for your crops, to several
activities that can impact food safety, including harvesting, cleaning packing equipment, and
handling raw manure and treated biological soil amendments of animal origin (BSAAOs). If the
scope of the worker’s previous assigned duties and farming experience did not provide the
worker with the level of food safety knowledge necessary to perform these new activities in a
manner that prevents contamination of covered produce, you could determine that the worker
needs additional food safety training, such as targeted training about cleaning and sanitizing
practices, and provide or otherwise arrange for that training.
You should evaluate your personnel’s current levels of training, education, and experience to
determine which personnel you will assign to supervise personnel who handle covered produce
or food contact surfaces. Such supervisors should have sufficient knowledge of food safety and
hygienic practices to ensure awareness of the requirements of the Produce Safety Rule among
personnel and to effectively determine whether other personnel are conducting activities in a
manner that complies with the Produce Safety Rule. As an example, one way a farm could
implement 21 CFR 112.31 (which requires you to take measures to prevent contamination of
covered produce and food contact surfaces with microorganisms of public health significance
from any person with an applicable health condition) is by assigning a specific individual to
determine daily whether arriving harvest personnel exhibit symptoms of an applicable health
condition, and to receive information from personnel about any symptoms or diagnoses of such
conditions. In such a circumstance, the assigned individual should have: 1) knowledge of the
symptoms of concern (e.g., vomiting, diarrhea); 2) knowledge of your procedure for excluding or
reassigning workers with applicable health conditions; and 3) the ability to implement your
procedures based on the requirements of the Produce Safety Rule in that area. You should also
ensure those who supervise the handling of covered produce and food contact surfaces can
recognize whether personnel, individually or collectively, need additional or more frequent
training as necessary and appropriate in light of observations or information indicating that

28

Contains Nonbinding Recommendations
Draft-Not for Implementation
personnel are not meeting standards established by FDA in subparts C through O of the Produce
Safety Rule.
The extent of education, training, and experience needed for personnel who handle covered
produce or food contact surfaces, and those engaged in the supervision thereof, could also
depend on the specific characteristics or organization of your farm. For example, a farm could
have a single worker responsible for completing several diverse activities (such as harvesting
produce, evaluating treatment of BSAAOs, and working in the packing area) that involve a
broader range of training topics for that worker. Conversely, a farm could have several
personnel working together to accomplish the same task, such as harvesting covered produce,
that involves focused training specific to that activity. Understanding the extent of your
personnel’s duties will help you identify and deliver appropriate training so that the personnel
who handle covered produce or food contact surfaces, and those engaged in the supervision
thereof, have the combination of education, training, and experience necessary to perform
assigned duties in compliance with the Produce Safety Rule.

3. Training Frequency
The personnel you identify as those who handle covered produce or food contact surfaces, and
those who are engaged in the supervision thereof, must receive adequate training:
•
•
•

Upon hiring (21 CFR 112.21(a));
Periodically thereafter, at least once annually (21 CFR 112.21(a)); and
As necessary and appropriate in light of observations or information indicating that
personnel are not meeting standards established by FDA in the Produce Safety Rule
subparts C through O (21 CFR 112.21(d)).

By providing training upon hiring, you introduce personnel to your procedures and the
requirements of the Produce Safety Rule applicable to their assigned duties before they handle
covered produce or food contact surfaces. Although you may hire personnel at different times
throughout the year to perform various activities, training must occur before personnel begin
duties that involve handling covered produce or food contact surfaces, regardless of when they
are hired (See 21 CFR 112.21(a)). For example, if you hire workers in December whose
assigned duties consist of performing clerical work throughout the year, and harvesting covered
produce from May to October, then as long as these workers’ duties do not entail handling
covered produce or food contact surfaces until May, you could choose to delay their initial
training until, for example, late April.
You must also provide periodic refresher training at least once annually for personnel who
handle covered produce or food contact surfaces, and those who are engaged in the supervision
thereof. (See 21 CFR 112.21(a)). Such training helps reinforce your personnel’s continued
awareness of their responsibility to follow food safety and hygiene principles, and the
requirements of the Produce Safety Rule. You have the flexibility to determine the appropriate
timing and frequency for periodic refresher training, as long as it occurs at least once per year.
Some issues that could influence your decision on timing and frequency include the type,
number, and timing of crops, and the timing of hiring and initial training for individual workers.
For example, if you use different personnel to grow and harvest covered produce, or if you have
29

Contains Nonbinding Recommendations
Draft-Not for Implementation
year-round production, and want to deliver training to smaller groups rather than all personnel at
once, then staggered, periodic refresher training could more effectively ensure that all personnel
receive the required training. For another example, you could decide to conduct periodic
refresher training more frequently than once a year (e.g., bi-annual or quarterly training
sessions), before personnel begin certain covered activities, such as before the beginning of the
growing season and again before the beginning of covered produce harvesting, particularly if
your training focuses on specific topics or activities.
You should provide personnel with the most up-to-date information, to the extent practical, from
credible sources. Academia, extension services, industry associations, and government agencies
can be useful sources of information. You should keep your procedures and training materials
updated and consider conducting periodic refresher training when new or additional information
becomes available, such as new information about practices that could contribute to foodborne
illness, or new recommendations about minimizing contamination. For example, a multi-state
outbreak of Listeria monocytogenes associated with cantaloupe led to 143 hospitalizations and
33 deaths in 2011 (Ref. 23). As a result, both FDA and produce industry trade associations
updated existing documents to provide information on how to minimize microbial contamination
of cantaloupe.
If you change your procedures (for example, as a result of new information about how to best
prevent contamination of covered produce you grow), you should update your training materials
to reflect your new procedures, and conduct refresher training for affected personnel.
Furthermore, you must repeat training, as necessary and appropriate in light of observations or
information indicating that personnel are not meeting standards established by FDA in subparts
C through O of the Produce Safety Rule. (21 CFR 112.21(d)). Observations and information
could be provided by, for example, supervisors, responsible parties, or other personnel. When
providing repeat training, you should determine whether certain training content needs to be
adapted in order to emphasize the conditions and practices necessary based on the requirements
of the Produce Safety Rule. For example, if your harvest crew supervisor reports that harvest
personnel are not consistently washing their hands after returning from breaks, you should
evaluate the available observations and information related to the harvest personnel’s practices.
You could determine that training is necessary for those personnel that are not meeting the
requirements of subpart D of the Produce Safety Rule; you would then provide refresher training
to those personnel. This training should include information about the public health significance
of proper hand-washing, your hand-washing procedures, and the requirements of the Produce
Safety Rule regarding hand-washing. The training could be coupled with a demonstration of
hand-washing technique.

4. Easily Understandable Training
Training must be conducted in a manner that is easily understood by personnel being trained.
(21 CFR 112.21(c)). You should provide training in the language that your personnel
customarily speak. Training should also be tailored to the educational level of your personnel,
using terminology that is commonly used and avoiding terminology that is unnecessarily
complex or easily misinterpreted. Training materials can include easily understood pictorials or
graphics of important concepts. You should deliver information in a manner that your personnel
30

Contains Nonbinding Recommendations
Draft-Not for Implementation
can relate to their assigned duties and provide examples that are relevant to your farm. You may
need to repeat key learning points in successive sessions, such as for complex topics, practices,
or procedures.
Training sessions should be designed to effectively deliver the content. Training can include
formal, scheduled events or less structured spontaneous sessions (e.g., in response to a real-time
observation of poor practices by a supervisor). Training sessions can include several topics or
can focus on information related to a specific topic or task. In some cases, longer training
sessions could be effective to provide more depth of information or provide personnel with time
to focus on complex concepts. Training conducted upon hiring or when introducing concepts to
personnel that have limited knowledge or experience with food safety topics could be longer than
other training sessions. Furthermore, dedicated training sessions can also emphasize your
commitment to implementing food safety procedures based on the requirements of the Produce
Safety Rule.
In some cases, training is most effective when it is provided in short sessions, focusing on a
specific topic that targets a specific food safety concern among small groups of personnel with
the same or similar duties (Ref. 101). When practical, these targeted training sessions should be
conducted at or near the applicable work area. For example, you could train personnel that
perform cleaning and sanitizing on treatment preparation near the area where these solutions are
made. In another example, you could train personnel that perform packing activities about
proper handling and cleanliness of food-packing materials, such as fiberboard boxes and plastic
totes near their workstation.
Hands-on practice or demonstrations can show your personnel how to perform a specific job
task, and provide opportunities for them to practice performing the task under supervision (Ref.
14) (Ref. 57). This allows your trainers to observe, discuss, and correct any poor practices
exhibited during training sessions. For example, to train your harvest personnel to recognize
covered produce that must not be harvested, as required by 21 CFR 112.22(b)(1), you might
provide demonstrations in which you show the personnel examples of covered produce they
should not harvest (e.g., covered produce contaminated with animal excreta) to prepare them to
look for and recognize certain conditions. As another example, you could train personnel
performing packing activities on inspection of food-packing materials (e.g., fiberboard boxes or
plastic totes) by showing and discussing the condition of food packing containers and whether
they could be contaminated with a known or reasonably foreseeable hazard.
You should consider posting signs or visual aids promoting practices presented in training as an
additional reminder for personnel and to reinforce training concepts. You should include, as
appropriate, multilingual versions, or pictorials or graphics. If you choose to post signs, you
should do so in areas as close as practical to where personnel perform the relevant activities.

5. Minimum Training Requirements
At a minimum, all personnel who handle covered produce or food contact surfaces during
covered activities or supervise the conduct of such activities must receive training described in
21 CFR 112.22. (21 CFR 112.22). As stated above, 21 CFR 112.21(a) establishes a training
requirement for certain personnel (that is, “all personnel who handle (contact) covered produce
31

Contains Nonbinding Recommendations
Draft-Not for Implementation
or food contact surfaces, or who are engaged in the supervision thereof”). The Produce Safety
Rule provides the minimum content that must be included in that required training at 21 CFR
112.22. While the section regarding training content (21 CFR 112.22) does not explicitly state
that it applies to personnel who contact food contact surfaces, FDA interprets that section to
apply to such individuals, and those engaged in the supervision thereof, as provided in the
section establishing the training requirement (21 CFR 112.21(a)). You should focus this training
on the principles that will help personnel understand how to perform their duties in a way that
aligns with the requirements of the Produce Safety Rule and how their actions can affect the
safety of covered produce and food contact surfaces. While not required by the Produce Safety
Rule, you should train other personnel in the same or similar fashion, as appropriate in light of
their duties. An evaluation of assigned duties for all of your personnel who engage in covered
activities (even if they do not handle covered produce or food contact surfaces), and their current
level of training, education, and experience should help you identify additional personnel for
whom it would be prudent to provide training and determine appropriate training for each
individual or group.
The topic areas addressed in 21 CFR 112.22(a)(1) and (2)–food hygiene, food safety, and health
and personal hygiene, and in 21 CFR 112.22(a)(3)–the standards in subparts C through O of the
Produce Safety Rule, represent the minimum topic areas you must cover during training for your
personnel who handle covered produce and food contact surfaces during covered activities, and
those who are engaged in the supervision thereof.
It is important to provide personnel with an understanding of the potential routes of
contamination of covered produce and food contact surfaces so that they can recognize how their
own practices have the potential to result in contamination. Your training program should also
include your food safety procedures. Your training programs can be designed to supplement
your personnel’s prior education, training, and experience. The Produce Safety Rule does not
specify who can provide training. You could choose to have qualified farm personnel or a third
party conduct your training activities.
Food Hygiene and Food Safety
Your training must explain the principles of food hygiene and food safety. (21 CFR
112.22(a)(1)). This provides an overall framework for job performance that helps ensure
compliance with the requirements of the Produce Safety Rule.
To meet the minimum requirements of food hygiene and food safety training, your training
topics should include:
•
•

Relevant sources of foodborne pathogens (e.g., humans and their waste; animals and their
waste);
Routes of contamination (e.g., animals or pests that contaminate covered produce with
their excreta; inadequately composted biological soil amendments of animal origin
(BSAAOs) handled in a way that results in contact with covered produce during
application; a worker with an applicable health condition who handles covered produce;
environmental transfer (e.g., contaminated soil or water contacting covered produce); and

32

Contains Nonbinding Recommendations
Draft-Not for Implementation

•
•

potential for cross-contamination (e.g., unclean surfaces contacting clean surfaces and
transferring contamination));
Preventive measures (i.e., taking measures to minimize the potential for contamination at
those points where potential routes of contamination exist); and
Corrective measures (e.g., identifying covered produce that has been exposed to the
potential for contamination and taking steps reasonably necessary to prevent the
introduction of known or reasonably foreseeable hazards and ensure that it is not
distributed for consumption, if necessary).

The content of your training should connect these principles to your personnel’s specific job
duties. If, for example, you are conducting training for personnel whose assigned duties include
removing trash from the packing area and infrequent handling of covered produce and food
contact surfaces, the training should explain that waste containers could be contaminated (e.g.,
by pests, animal fecal material tracked onto the floor of the packing area, or in the area of the
dumpster) and the potential for cross-contamination when they transition from handling trash and
waste containers to handling covered produce and food contact surfaces (e.g., helping other
personnel move covered produce, and containers holding covered produce, on packing tables).
The training should also explain how to recognize practices (e.g., using packing tables as a break
space over lunch) that could result in cross-contamination of covered produce.
Health and Personal Hygiene
Your training must explain the importance of health and personal hygiene for personnel and
visitors; this training must include information on recognizing the symptoms of a health condition
(e.g., vomiting, diarrhea, open lesions) that is reasonably likely to result in the contamination of
covered produce or food contact surfaces. (21 CFR 112.22(a)(2)). Further, your training should
ensure that personnel understand that they have a responsibility to take action to prevent
contamination due to their own health (i.e., communicable illness) and hygienic practices. For
those who handle covered produce or food contact surfaces, or who are engaged in the
supervision thereof, your training must also include the requirements of the Produce Safety Rule
related to health and personal hygiene that are applicable to their job responsibilities. (21 CFR
112.22(a)(3); see the section of this chapter titled “Standards in Subparts C through O”. Training
topics for the applicable personnel regarding health and personal hygiene must include:
•
•

Recognizing and reporting, as necessary, applicable health conditions as outlined in 21
CFR 112.31; and
Hygienic practices to minimize the potential of contamination to covered produce and
food contact surfaces, including those outlined in 21 CFR 112.32(b).

Draft guidance on personnel and visitor health and hygiene is provided in Chapter 3: Health and
Hygiene (Subpart D).
You should train all personnel who handle covered produce or food contact surfaces to recognize
and respond when they encounter situations that present the potential for contamination of
covered produce or food contact surfaces. For example, if your worker’s assigned duties include
handling raw manure as well as harvesting covered produce by hand, you should train them to
know how their activities could result in cross-contamination between the raw manure and the
33

Contains Nonbinding Recommendations
Draft-Not for Implementation
covered produce. Further, the training should include your procedures regarding personal
hygienic practices. Your training should include instructions to report to a supervisor or
responsible individual any situations that the worker observes or becomes aware of that could
result in contamination of covered produce or food contact surfaces.
Standards in Subparts C through O
Training must cover the standards established by FDA in subparts C through O of the Produce
Safety Rule that are applicable to the employee’s job responsibilities. (21 CFR 112.22(a)(3)).
You should develop or use training programs that ensure that your personnel understand the
regulatory requirements that are applicable to their job responsibilities. The standards in
subparts C through O often involve action by your personnel that requires a specific
understanding of certain practices and their impact on food safety, without which personnel may
not meet the standards. Demonstrations are one method to show personnel examples of
appropriate or inappropriate practices.
The following are a few examples that connect job responsibilities with job-specific training
topics. These examples are intended to illustrate concepts for certain types of job responsibilities
and are not intended to be universally applicable. Even if you have personnel with similar job
responsibilities to those mentioned here, you should perform your own evaluation based on your
farm’s specific practices and conditions.
Example 2a. For personnel who sort covered produce by hand after harvest, training:
o must include the requirements of the Produce Safety Rule that are applicable to
their duties–including those in subpart D–Health and Hygiene, and subpart K–
Growing, Harvesting, Packing, and Holding Activities–that relate to sorting
covered produce (See 21 CFR 112.22(a)(3)).
o should include your farm’s procedures related to sorting covered produce–
including what to do with covered produce that is reasonably likely to be
contaminated.
o should include how the personnel’s actions while sorting covered produce can
lead to contamination of food contact surfaces and covered produce (e.g.,
situations where cross-contamination could occur).
Example 2b. For personnel who clean and sanitize packing equipment with food contact
surfaces, training:
o must include the requirements of subpart L–Equipment, Tools, Buildings, and
Sanitation–that relate to equipment cleaning and sanitizing (See 21 CFR
112.22(a)(3)).
o should include your procedures related to equipment cleaning, including how to
prepare the cleaning and sanitizing solutions.
o should include how the personnel’s actions while cleaning the equipment (e.g.,
dragging a hose from the floor across a clean food contact surface) can lead to
contamination of food contact surfaces.

34

Contains Nonbinding Recommendations
Draft-Not for Implementation
Example 2c. For personnel who harvest covered produce by hand, and manage
biological soil amendments of animal origin (BSAAOs), including a treatment process
and keeping records of process controls, training:
o must include the requirements of the Produce Safety Rule that are applicable to
their duties, including those in subpart C–Personnel Qualifications and Training
that relate to those who harvest covered produce, subpart D–Health and Hygiene
that relate to harvesting covered produce by hand, subpart F–Biological Soil
Amendments of Animal Origin and Human Waste that relate to preparing,
handling, conveying, and storing BSAAOs and keeping records of the treatment
process, subpart K–(Growing, Harvesting, Packing, and Holding Activities that
relate to harvesting covered produce, and subpart O–Records that relate to
keeping records of process controls.
o should include your procedures related to harvesting activities, managing
untreated and treated BSAAOs, including your treatment procedures and
recordkeeping system.
o should include how the personnel’s actions while performing certain practices
(e.g., handling raw manure and then handling a clean food contact surface) can
lead to contamination of covered produce and food contact surfaces.
Example 2d. For personnel who supervise the pest control activities for your farm and do
not contact covered produce or food contact surfaces, training:
o should include the requirements of subpart L–Equipment, Tools, Buildings, and
Sanitation that relate to pest control.
o should include your procedures related to pest control.
o should include how the personnel’s activities while overseeing the pest control
activities (e.g., handling traps and bait stations then contacting a clean food
contact surface) can lead to contamination of food contact surfaces and covered
produce.
o should include how to recognize signs of pest infestation and animal excreta.
o should include how pests can contaminate covered produce.

6. Additional Training for Persons Who Conduct Harvest Activities
There are specific training requirements for personnel who conduct harvest activities for covered
produce (21 CFR 112.21(b)), in addition to the previously discussed training requirements that
apply to all personnel who handle covered produce or food contact surfaces.
As part of this training, you should encourage your personnel to communicate with their
supervisors or responsible parties, or directly with other personnel, if they observe harvesting
practices that do not align with your procedures or the applicable requirements of the Produce
Safety Rule. Examples of such observations include harvesting covered produce visibly
contaminated with animal excreta, harvesting dropped covered produce, or observing contact
between cut surfaces of covered produce and the soil during or after harvest. (Additional
information on these observations is found in 21 CFR 112.83, in Chapter 5: Domesticated and
Wild Animals (Subpart I), in 21 CFR 112.112 and 112.113, and in Chapter 6: Growing,
Harvesting, Packing, and Holding Activities (Subpart K.)).
35

Contains Nonbinding Recommendations
Draft-Not for Implementation
You could use contracted or temporary personnel to perform certain activities–for example to
perform harvesting activities–but you should ensure that all personnel, including contracted,
part-time, and temporary personnel, meet all of the training requirements of subpart C. For
example, you could choose to rely on training that the company with whom you contract delivers
to their harvesting crews to meet the requirements of subpart C. You should evaluate the
training content to ensure that it meets the Produce Safety Rule requirements and aligns with
your procedures. You may need to provide additional training to address any topics not covered
by the contract company’s training, for example, to ensure the harvest personnel are aware of
your specific procedures.
Recognizing When Not to Harvest Covered Produce
Persons who conduct harvest activities must be trained to recognize covered produce that must
not be harvested. (21 CFR 112.22(b)(1)). This includes covered produce that may be
contaminated, such as by animal excreta (see also draft guidance in Chapter 6: Growing,
Harvesting, Packing, and Holding Activities (Subpart K), titled “Identifying and Not Harvesting
Contaminated Covered Produce.” The training should emphasize to personnel that identifying
and not harvesting covered produce that may be contaminated is potentially the only opportunity
to prevent that covered produce from reaching consumers. Other personnel conducting activities
that follow harvesting may not observe or be aware of the signs of possible contamination that
harvest personnel are able to observe.
You should evaluate your harvesting activities and add training content specific for harvest
personnel, as applicable to your farm’s operations. In particular, you should include the
following training topics for personnel conducting harvesting activities:
•

Recognizing covered produce that is reasonably likely to be contaminated with a known
or reasonably foreseeable hazard (e.g., excreta, bite marks, crop destruction) immediately
prior to and during harvesting (see also discussion of 21 CFR 112.112 and draft guidance
in Chapter 6: Growing, Harvesting, Packing, and Holding Activities (Subpart K), titled
“Identifying and Not Harvesting Contaminated Covered Produce”); and

•

As applicable, recognizing specific growing areas from which covered produce possibly
should not be harvested due to significant evidence of potential contamination from
animals observed during the growing season (see also discussion of 21 CFR 112.83 and
draft guidance in Chapter 5: Domesticated and Wild Animals (Subpart I), titled
“Evaluating Significant Evidence of Potential Contamination of Covered Produce by
Animals to Determine Whether Harvest Can Occur”).
Harvest Containers and Equipment

Persons who conduct harvest activities for covered produce must receive training on inspecting
harvest containers and equipment to ensure that they are functioning properly, clean, and
maintained so as not to become a source of contamination of covered produce with known or
reasonably foreseeable hazards. (21 CFR 112.22(b)(2)). Such persons must also receive training
on correcting problems with harvest containers or equipment, or reporting such problems to a
supervisor or other responsible party as appropriate to the person’s job responsibilities. (21 CFR
36

Contains Nonbinding Recommendations
Draft-Not for Implementation
112.22(b)(3)). Covered produce is often hand-harvested or hand-packed, sometimes directly into
consumer-ready containers, so it is important for personnel to understand the influence of these
practices on food safety (Ref. 14) (Ref. 64).
You should train personnel who harvest covered produce to visually assess harvest containers
(e.g., food-packing materials, consumer-ready containers, and those from which the covered
produce will be repacked) to determine whether they could serve as a source of contamination to
the covered produce (see also Chapter 6: Growing, Harvesting, Packing, and Holding Activities
(Subpart K), especially the discussion related to food-packing materials).
Training should include:
•

•
•

•
•

Types of handling and practices that can contaminate food contact surfaces of
harvesting containers (e.g., illustrations of a worker with an uncovered hand
wound touching the food contact surface of a harvest container, or a worker
stepping on the food contact surface of a harvest container, or animal excreta
present on food contact surfaces);
How and when personnel should inspect harvest containers;
Conditions that personnel should look for during their inspections (e.g., visible
animal excreta; organic material; residue; debris; evidence of pests or animals; or
containers that are cracked, pitted, scored, or otherwise damaged in a way that
promotes the growth or transfer of bacteria);
Conditions that indicate the containers should be discarded; and
Examples of damaged or unclean harvest containers to help illustrate when
cleaning or repair is needed and when the containers should be discarded may be
helpful. For example, displays or photos of several harvest containers in different
stages of disrepair and an explanation of the expected corrections for each
container or examples of harvest containers that should be cleaned prior to use
may be helpful.

7. Food Safety Training for a Supervisor or Responsible Party
At a minimum, at least one supervisor or responsible party for your farm must have successfully
completed food safety training at least equivalent to that received under standardized curriculum
recognized as adequate by the FDA. (21 CFR 112.22(c)). The standardized curriculum was
developed by the Produce Safety Alliance (PSA), and is offered as one way to meet this
requirement. You may use other training programs as long as the training is equivalent to the
standardized curriculum. The standardized curriculum covers fundamental food safety topics as
they relate to produce and the requirements of the Produce Safety Rule, including an introduction
to produce safety, worker health and hygiene, training, wildlife and domesticated animals, land
use, agricultural water, produce handling, and sanitation.
You could choose to have additional supervisors, or other personnel, complete this training as
well. For example, if your farm has several supervisors who are responsible for ensuring that
your operations adhere to the requirements of the Produce Safety Rule, you could direct each of
these supervisors to complete the standardized or equivalent training. We also encourage you to
37

Contains Nonbinding Recommendations
Draft-Not for Implementation
have those who complete the standardized curriculum training (or equivalent) share what they
learned with other personnel on your farm, during your on-farm training or otherwise.

8. Supervision to Ensure Compliance
You must assign or identify personnel to supervise (or otherwise be responsible for) your
operations to ensure compliance with the requirements of the Produce Safety Rule. (21 CFR
112.23). Such personnel can include full-time, permanent, temporary, part-time, seasonal,
contracted, or other personnel you designate as responsible for ensuring that your activities
comply with the requirements of the Produce Safety Rule. Oversight by qualified personnel is
essential to ensure compliance with the Produce Safety Rule. These supervisors or responsible
individuals should be able to evaluate whether other personnel are conducting activities in a
manner based on the requirements of the Produce Safety Rule. (See 21 CFR 112.23). You
should ensure that your responsible individuals or supervisors are aware of their role in
recognizing and ensuring the correction of deviations from your food safety procedures and the
requirements of the Produce Safety Rule. They should know that if they notice that a worker is
not adhering to a food safety protocol, they should ensure that the worker receives immediate
corrective training (e.g., instructions). For example, if a supervisor observes a worker harvesting
covered produce with obvious animal excreta, the supervisor should show all harvest personnel
the affected produce and remind personnel of why such produce must not be harvested (See 21
CFR 112.112). Your responsible individuals or supervisors also should recognize when
individual deviations are recurring, or are more widespread among personnel, as this could signal
a need to find a better way to convey the principles of the training materials to the personnel or
to provide more frequent periodic refresher training.
You should evaluate your operations and ensure that you have identified personnel to supervise
or be responsible for each aspect of your operations that relates to a provision of the Produce
Safety Rule. You could find that you will need multiple individuals to fill this role but, in some
cases, one individual could be able to perform all of the necessary duties to ensure compliance.
These individuals can play an integral role in ensuring food safety and building a culture of food
safety on your farm.

9. Training Records
You must establish and keep records of training that document required training of personnel,
including the date of training, topics covered, and the person(s) trained. (21 CFR 112.30(b)).
An example of a record that meets the training records requirements is an attendance sheet for a
training session that includes the date of training, list of personnel in attendance, and list of
topics covered (e.g., proper hand-washing). The records requirement applies regardless of
whether you, a supervisor, or a responsible individual, or another entity, provides the training. If
you employ contracted personnel, and you choose to rely on the training the contracted company
(or a third-party service provider) provides, you should request training documentation from the
contracted company or third-party service provider, and maintain the records to demonstrate
compliance with the training requirements. (See additional draft guidance related to general
recordkeeping requirements provided in Chapter 8: Records (Subpart O)).

38

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 3:
Health and Hygiene (Subpart D)
People can contaminate covered produce and food contact surfaces with pathogens by failing to
maintain hygiene practices; thereby potentially impacting the health of those who consume the
contaminated produce (Ref. 70) (Ref. 138). Unhygienic practices exhibited by farm personnel
have contributed to some produce-related outbreaks (Ref. 70) (Ref. 138). Human skin and
clothing can transfer contamination in a variety of ways, including when a person uses the
restroom, contacts other parts of the body or contaminated surfaces (e.g., unclean surfaces, soil,
floors, trash, animals), and then handles covered produce or food contact surfaces (Ref. 58) (Ref.
81) (Ref. 116). Health and hygiene practices of personnel and visitors are therefore directly
relevant to produce safety.
People can carry and transmit pathogens harbored on their skin and in their gastrointestinal and
respiratory tracts. Individuals have the potential to spread communicable illnesses even if they
do not show symptoms (i.e., asymptomatic carriers) (Ref. 24) (Ref. 131) (Ref. 56).
Asymptomatic carriers do not show symptoms because they either have not yet developed
symptoms, symptoms never manifested, or their symptoms have resolved or subsided (Ref. 56)
(Ref. 24) (Ref. 131). These individuals might not be aware that they are an asymptomatic carrier
with the potential to spread a communicable illness, and may not seek medical examination,
receive a diagnosis, or treat their illness. Therefore, hygienic practices are important in
protecting covered produce and food contact surfaces from contamination by people who could
transmit pathogens.
The requirements of subpart D establish minimum requirements to reduce the likelihood that
personnel and visitors will introduce contamination to covered produce or food contact surfaces.
The areas of focus include: preventing ill or infected persons from contaminating covered
produce; implementing hygienic practices to minimize the risk of contamination by personnel;
and minimizing the risk of contamination by visitors. Following these practices will help
prevent contamination of covered produce or food contact surfaces from individuals with
applicable health conditions (see the section of this chapter titled “Understanding Applicable
Health Conditions”) or from unhygienic practices.
Much of the responsibility to prevent contamination of covered produce and food contact
surfaces through hygienic practices rests with your personnel; it is important for you to
communicate that responsibility to your personnel. The requirements and recommendations
discussed in this chapter include not only actions directed at you–the owner, operator, or agent
(as defined in 21 CFR 112.3)–but also actions directed at your supervisors or responsible parties,
and your personnel. Personnel can include full-time, part-time, contracted, and seasonal
personnel; volunteers; and paid or unpaid interns at your facility.

1. Measures to Prevent Ill or Infected Persons from Contaminating
Covered Produce
This section contains draft guidance on:

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•
•
•

Applicable health conditions;
The responsibility of personnel to recognize and report applicable health conditions to a
supervisor or responsible party;
The role of supervisors and responsible parties in identifying applicable health
conditions;
Addressing reports of applicable health conditions; and
Responding to potential contamination of covered produce or food contact surfaces.

Among other requirements, 21 CFR 112.31 requires you to:
•

•

Exclude any person from working in any operations that may result in contamination of
covered produce or food contact surfaces with microorganisms of public health
significance when the person is shown to have, or appears to have, an applicable health
condition, until the person’s health condition no longer presents a risk to public health;
and
Instruct personnel to notify their supervisor(s) or a responsible party if they have, or if
there is a reasonable possibility that they have, an applicable health condition.

You should also:
•
•

Ensure that you and your supervisors, responsible parties, and personnel can identify
applicable health conditions; and
Ensure that your supervisors and responsible parties are aware of their responsibilities to:
o Remind personnel to report applicable health conditions;
o Evaluate whether personnel understand and report applicable health conditions;
o Understand procedures to address reports of applicable health conditions; and
o Know how to respond to potential contamination of covered produce or food
contact surfaces.
Understanding Applicable Health Conditions

You must take measures to prevent contamination of covered produce and food contact surfaces
with microorganisms of public health significance from any person with an applicable health
condition. (21 CFR 112.31(a)). This could include, for example, full-time, part-time,
contracted, and seasonal personnel; volunteers; unpaid and paid interns; and/or visitors.
Applicable health conditions include communicable illnesses that present a public health risk in
the context of normal work duties. The scientific evidence from outbreaks, surveys, and
published literature establishes that human pathogens (e.g., Salmonella, pathogenic E. coli,
Shigella, and Cyclospora) constitute a biological hazard with the potential to cause serious
adverse health consequences or death, and result in the vast majority of foodborne illness known
to be associated with produce consumption (Ref. 28) (Ref. 121).
Signs and symptoms (Ref. 27) (Ref. 98) (Ref. 115) (Ref. 55) of applicable health conditions can
include the following:
•

Vomiting;
40

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•
•
•

Diarrhea;
Abdominal cramps;
Sore throat with fever;
Jaundice (yellowish discoloration of the skin or of parts of the eyes); and
Open wounds (e.g. wounds, boils, cuts, or sores).

Keep in mind that in some instances some non-communicable conditions and diseases can cause
symptoms (e.g., vomiting, diarrhea) similar to those caused by the communicable illnesses
described above. Applicable health conditions do not include conditions such as pregnancy, or
non-communicable diseases such as cancer, diabetes, and high blood pressure. You should
encourage personnel to report relevant symptoms, such as vomiting or diarrhea, to supervisors or
responsible parties, regardless of the underlying condition, and your procedures should specify
how to respond to such reports. For further draft guidance, see the section of this chapter titled
“Addressing Reports of Applicable Health Conditions.”
Self-identification of Applicable Health Conditions
You must instruct your personnel to notify their supervisors (or a responsible party) if they have,
or if there is a reasonable possibility that they have, an applicable health condition. (21 CFR
112.31(b)(2)). Your personnel could become aware by self-identification or medical
examination that they have, or there is a reasonable possibility that they have, an applicable
health condition.
You should ensure that personnel who have the potential to contaminate covered produce or food
contact surfaces can identify applicable health conditions. Such personnel include those who
handle covered produce and food contact surfaces, and those who interact with personnel who
handle covered produce and food contact surfaces.
As discussed in this draft guidance at Chapter 2: Personnel Qualifications and Training (Subpart
C), personnel who handle covered produce or food contact surfaces must receive training in the
importance of health and personal hygiene, including recognizing symptoms of a health
condition that is reasonably likely to result in contamination. (21 CFR 112.22(a)(2)). Such
personnel also must receive training that includes the requirements established in subpart D of
the Produce Safety Rule that are applicable to their job responsibilities. (See 21 CFR
112.22(a)(3)). This training is one way a farm can satisfy its obligation to instruct its personnel
to notify their supervisors (or a responsible party) if they have, or if there is a reasonable
possibility that they have, an applicable health condition. (21 CFR 112.31(b)(2)). You should,
for example, in the training provided for those personnel that you assign to pack covered produce
by hand, include training on applicable health conditions and the need to report to a supervisor or
other responsible party any applicable health conditions that they might have.
For those personnel not covered by the training requirements in 21 CFR 112.22(a)(2) and (3),
you should evaluate their job duties to determine whether you should provide them with training
that ensures that they are aware of health and hygiene topics that are applicable to their job
duties; depending on the circumstances, these personnel could contaminate covered produce or
food contact surfaces if they have an applicable health condition. This includes personnel who
do not handle covered produce or food contact surfaces themselves but interact with personnel
41

Contains Nonbinding Recommendations
Draft-Not for Implementation
who do. For examples, see the section of this chapter titled “Addressing Reports of Applicable
Health Conditions.”
You have the flexibility to determine how to provide awareness of the requirements of 21 CFR
112.31(b)(1) and (2) to your personnel. For example, you could have all personnel attend
training on this topic at the same time. You also could, for example, provide separate training on
health and hygienic practices for personnel who do not handle covered produce or food contact
surfaces and for those who handle covered produce or food contact surfaces.
To promote self-identification of applicable health conditions by personnel, you should:
•

•

•

•
•

Train all personnel who may contaminate covered produce or food contact surfaces (not
just those subject to the training requirement in 21 CFR 112.22(a)) on applicable health
conditions and how to identify them, including relevant symptoms and communicable
illnesses of concern;
Encourage personnel to be aware of their direct contact with, or exposure to, individuals
with symptoms of applicable health conditions (e.g., vomiting, diarrhea), including away
from your farm and in their homes. 8 Remind personnel that they could also become ill or
could become an asymptomatic carrier (as described in this chapter’s introduction). You
should emphasize that if personnel have direct contact with or exposure to symptomatic
individuals, they should pay careful attention to their hygienic practices (e.g., frequently
wash hands). If personnel do have such contact or exposure, they should carefully
monitor their health for potential symptoms of an applicable health condition;
Provide your personnel with information on which supervisor or responsible party to
notify if they have, or if there is a reasonable possibility that they have, an applicable
health condition. Remind personnel that if a medical provider diagnoses them with an
applicable health condition, information from the medical provider about the time period
during which the worker is likely to be contagious could be helpful to you in determining
appropriate steps regarding exclusion from duties that involve covered produce or food
contact surfaces;
Encourage personnel to prompt co-workers exhibiting symptoms of applicable health
conditions to report their condition to a supervisor or responsible party; and
Consider using signs or visual aids (e.g., posters) to reinforce important concepts
regarding health and hygiene.
Role of Supervisors in Identifying Applicable Health Conditions

Communication between supervisors or other responsible parties and personnel plays an
important role in ensuring that personnel continue to be aware of and report applicable health
conditions. You should ensure that supervisors and responsible parties are aware of their
responsibilities regarding the health and personal hygiene requirements of the Produce Safety
Rule. (See 21 CFR 112.22(a)(2)). For example, if you assign a supervisor to make a daily
assessment of whether harvest personnel exhibit symptoms of an applicable health condition and
8

An investigation in 2008 of a Salmonella outbreak associated with cantaloupe found that farm personnel and their
families had recently experienced gastrointestinal illness. (Ref. 32).

42

Contains Nonbinding Recommendations
Draft-Not for Implementation
receive information from personnel about their awareness of such conditions (because personnel
recognize the condition themselves or are made aware of a condition as a result of a medical
examination), you should ensure that the supervisor can recognize applicable health conditions,
including the signs and symptoms of concern (e.g., vomiting, diarrhea, frequently visiting the
toilet facilities) and knows when and how to exclude or reassign affected workers from
operations through which they could contaminate covered produce or food contact surfaces.
Supervisors should periodically remind personnel to report any applicable health conditions or
symptoms of concern they experience or observe in other personnel.
Addressing Reports of Applicable Health Conditions
You must exclude any person from working in any operations that may result in contamination
of covered produce or food contact surfaces with microorganisms of public health significance
when the person (by medical examination, the person’s acknowledgement, or observation) is
shown to have, or appears to have, an applicable health condition, until the person’s health
condition no longer presents a risk to public health. (21 CFR 112.31(b)(1)). You should be
aware that the measures to prevent contamination described in 21 CFR 112.31(a) apply to any
person who is shown to have, or appears to have, an applicable health condition. For example,
if a mechanic who is contracted to repair non-food contact equipment located in your farm’s
packing area, near where covered produce and food contact surfaces are exposed, could contact
covered produce or food contact surfaces while repairing equipment, that contact can result in
contamination if the mechanic has an applicable health condition. As another example, an
unpaid intern who assists personnel packing covered produce could perform tasks that could
contaminate covered produce or food contact surfaces, such as bringing food packing materials
with food contact surfaces to the packing area.
When presented with a report of a worker with an applicable health condition, you or a
supervisor (or a responsible party) should evaluate the worker’s applicable health condition and
job duties to determine appropriate measures to prevent contamination of covered produce and
food contact surfaces. Depending on the worker’s specific condition, and the specific operations
involved, such measures could include temporarily assigning the worker to other duties,
temporarily excusing them from work, or allowing the worker to continue with their job duties
after completing certain actions, such as bandaging a wound in a manner that prevents
contamination. For example, you must not permit a worker who reports currently experiencing
episodes of vomiting to directly handle covered produce or food contact surfaces until their
condition no longer presents a risk to public health, and you must exclude that worker from
activities where the potential for contamination of covered produce or food contact surfaces
exists through indirect contact (e.g., handling shared objects with other personnel who also
contact the covered produce or food contact surfaces), until their condition no longer presents a
risk to public health. (See 21 CFR 112.31(b)(1)).
The Produce Safety Rule does not require (or authorize) you to obtain medical records of your
personnel to determine or verify their applicable health condition. You and your supervisors and
other responsible parties should keep worker reports of applicable health conditions confidential
and address such reports as necessary to prevent contamination of covered produce or food
contact surfaces. Supervisors should not reprimand or otherwise penalize personnel based on a
report of an applicable health condition.
43

Contains Nonbinding Recommendations
Draft-Not for Implementation
In some cases, it may be possible to temporarily reassign a worker with an applicable health
condition to other tasks to prevent contamination of covered produce or food contact surfaces,
such as clerical activities in areas away from covered activities or waste removal in areas where
covered activities do not occur. If a worker’s applicable health condition involves a wound, boil,
cut, or sore that can be adequately covered to prevent it from becoming a source of
contamination, you could allow the individual to handle covered produce or food contact
surfaces after the worker covers the wound, boil, cut, or sore in a manner that prevents
contamination. Depending on the location of the wound, boil, cut, or sore, adequate covering
could involve the use of an impermeable bandage, finger cot, or glove. A supervisor or other
responsible party should assess the covered wound to determine whether it no longer presents a
public health risk before allowing a worker to handle covered produce or food contact surfaces.
(See 21 CFR 112.31(b)(1)).
You should develop procedures in advance to assist supervisors and other responsible parties in
making decisions about excluding or reassigning workers with applicable health conditions and
ensure these personnel are aware of your procedures. These procedures could account for
specific symptoms associated with applicable health conditions and categories of personnel
based on scope of job duties to ensure that any reassignment prevents contamination of covered
produce and food contact surfaces. The FDA Food Code is a resource that provides information
on potential approaches for addressing situations in which personnel have certain communicable
illnesses or conditions that represent a public health risk when handling food (Ref. 55).
Response to Potential Contamination of Covered Produce or Food Contact Surfaces
You must take appropriate measures to minimize the risk of serious adverse health consequences
or death from the use of, or exposure to, covered produce, including those measures reasonably
necessary to prevent the introduction of known or reasonably foreseeable hazards into covered
produce, and to provide reasonable assurances that the produce is not adulterated under section
402 of the FD&C Act because of such hazards. (21 CFR 112.11). For example, if you are aware
that a person with an applicable health condition is likely to have contaminated covered produce
or food contact surfaces, you must take appropriate measures to ensure that the affected produce
is not distributed unless its safety can be reasonably assured, and to prevent contamination of
additional covered produce. (See 21 CFR 112.11).
You should train supervisors and personnel who work in areas where covered activities occur on
how to respond to situations where a person with an applicable health condition could
contaminate covered produce. When such a situation occurs, you should consider taking
additional actions such as the following:
•
•
•
•

Isolating the areas of potential contamination and ceasing activities in the area until the
incident has been addressed;
Isolating and holding covered produce that could have been contaminated until its safety
can be evaluated;
Disposing of any covered produce that could have been contaminated unless its safety
can be assured; and
Cleaning and sanitizing, or replacing affected surfaces in the area, as appropriate.
44

Contains Nonbinding Recommendations
Draft-Not for Implementation
For example, if a worker unexpectedly becomes ill during the work shift and vomits on covered
produce on a packing belt, the worker should report the incident to a supervisor or responsible
party. The supervisor or responsible party should then ensure that activities in that area cease
and must exclude the worker from working in any operations that may result in contamination of
covered produce or food contact surfaces until the person’s condition no longer presents a risk to
public health (See 21 CFR 112.31(b)(1)). A supervisor or other responsible party should also
oversee the removal of the affected covered produce, and ensure other appropriate measures are
performed, such as cleaning and sanitizing of the affected food contact surfaces.
There could be occasions when you find that the requirements of 21 CFR 112.31 are not being
met at your farm. For example, if you learn that a supervisor did not adequately respond to a
report of a worker with an applicable health condition and your farm consequently failed to
exclude the worker from an operation that may result in contamination of covered produce or
food contact surfaces while the worker’s condition presented a risk to public health, you should
consider taking steps such as retraining that supervisor (or all supervisors) as necessary in
accordance with 21 CFR 112.21(d). In addition, under 21 CFR 112.11, you should consider, for
example, whether to change your farm’s procedures for responding to reports of applicable
health conditions.

2. Hygienic Practices
This section contains draft guidance on the following:
•
•
•

Hygienic practices and the requirements for personnel who work in an operation in
which covered produce or food contact surfaces are at risk of contamination with known
or reasonably foreseeable hazards to use hygienic practices;
The role of supervisors in ensuring personnel adhere to hygienic practices; and
Specific hygienic practices required under 21 CFR 112.32(b).

You should take the following steps to ensure your personnel are implementing required
hygienic practices (21 CFR 112.32):
•
•

•

•

Ensure that applicable personnel are aware of the hygienic practices requirements of the
Produce Safety Rule and can identify, and correct or report, unhygienic practices;
Identify job duties in which personnel are likely to encounter potential sources of
contamination (e.g., handling of biological soil amendments of animal original
(BSAAOs), animals, or waste) and, as appropriate, ensure that applicable personnel are
aware of hygienic practices;
Ensure personnel are aware of procedures associated with minimum hygienic
requirements of the Produce Safety Rule, including maintaining adequate personal
cleanliness, avoiding contact with animals other than working animals, thorough handwashing, using gloves (if applicable), wearing jewelry, eating, chewing gum, and using
tobacco products; and
Ensure your supervisors and responsible parties observe personnel and communicate with
personnel about hygienic practices, and identify unhygienic practices that need to be
addressed.
45

Contains Nonbinding Recommendations
Draft-Not for Implementation
Personnel and Hygienic Practices
Personnel who work in an operation in which covered produce or food contact surfaces are at
risk of contamination with known or reasonably foreseeable hazards must use hygienic practices
while on duty to the extent necessary to protect against such contamination. (21 CFR 112.32(a)).
This requirement is not limited only to personnel who handle covered produce and food contact
surfaces, but also applies to others who work in the operation. You should evaluate those
covered activities where covered produce or food contact surfaces are at risk of contamination
and ensure that your personnel are following hygienic practices to prevent contamination,
adjusting your procedures as necessary.
You should ensure that all personnel, including individuals whose job duties may not directly
involve covered produce or food contact surfaces—such as office or loading dock staff who
occasionally enter a packing area, use hygienic practices while on duty to the extent necessary to
protect against contamination and understand how hygienic practices impact the safety of
covered produce. For example, at a farm that grows covered produce and raises livestock, even
if specific personnel are designated to handle only livestock, if their duties are such that they
occasionally enter areas where they could contact covered produce or food contact surfaces with
footwear or clothing that contacted animal excreta, their clothing could transfer contamination to
covered produce or food contact surfaces if the worker does not follow hygienic practices.
You should identify personnel whose job duties are likely to involve interaction with potential
sources of contamination (such as handling trash, raw manure, or animals). You should consider
how these personnel interact with or come into proximity with other personnel and with covered
produce and food contact surfaces. If you determine that the personnel’s interactions create a
risk for contamination of covered produce or food contact surfaces, you should ensure that they
are aware of (such as through training), and follow, hygienic practices to protect against such
contamination.
Personnel should understand the importance of consistently following hygienic practices to
prevent contamination, and when hygienic practices are necessary. Personnel should be able to
identify and report unhygienic practices that they observe, and you should encourage them to do
so. In addition to training, you could use signs, visual aids (e.g., posters), and verbal reminders
to re-enforce to personnel the importance of using hygienic practices. For example, you could
place signs or visual aids by the entrance to a common area, such as a packing area, reminding
personnel to use hygienic practices, including those outlined in 21 CFR 112.32(b).
Role of Supervisors in Ensuring Personnel Follow Hygienic Practices
You must assign or identify personnel to supervise (or otherwise be responsible for) your
operations to ensure compliance with the requirements of the Produce Safety Rule. (21 CFR
112.23). The supervisors or other responsible parties you assign should ensure that other
personnel consistently follow hygienic practices on your farm. Supervisors or responsible
parties should observe and communicate with personnel who have the potential to contaminate
covered produce or food contact surfaces about hygienic practices to ensure awareness and
implementation. Supervisors and responsible parties should be familiar with the regulatory
requirements regarding health and hygienic practices as well as your procedures.
46

Contains Nonbinding Recommendations
Draft-Not for Implementation
You should instruct your supervisors and responsible parties to observe personnel when
performing their job duties to determine whether personnel are following hygienic practices and
to identify and respond to any unhygienic practices. You must perform or assign additional
training for the appropriate personnel, as necessary and appropriate, to correct those practices
that do not meet the requirements established by FDA in subpart D of the Produce Safety Rule.
(See 21 CFR 112.21(d)). In addition, under 21 CFR 112.11, you should consider any other
actions you may need to take to ensure compliance with the Produce Safety Rule. For example,
consider whether you should change your farm’s procedures for responding to reports of
unhygienic practices.
You should also ensure that supervisors are aware of your procedures and the applicable
requirements of the Produce Safety Rule, which can be achieved as part of required training (See
21 CFR 112.22(a)). For example, if you assign a supervisor to oversee harvest activities in a
field where covered produce is handled, the supervisor must receive training including the
requirements of subpart D, such as adequate personal cleanliness and thorough hand-washing,
that are relevant to the supervisor’s job responsibilities. (21 CFR 112.22(a)(3)). The supervisor
should also understand your related procedures. For supervisors and responsible parties not
subject to the training requirements in 21 CFR 112.22(a), you should nonetheless provide
training that ensures that they are aware of the regulatory requirements for health and hygiene
that are applicable to their job duties.
Required Hygienic Practices
Personnel who work in an operation in which covered produce or food contact surfaces are at
risk of contamination with known or reasonably foreseeable hazards must use hygienic practices
while on duty to the extent necessary to protect against such contamination. (21 CFR 112.32(a)).
The hygienic practices that personnel use to satisfy the requirements of 21 CFR 112.32(a) when
handling covered produce or food contact surfaces during a covered activity must include those
provided in 21 CFR 112.32(b). (21 CFR 112.32(b)). These represent the minimum requirements
for hygienic practices that all operations must apply. In addition, you should evaluate your
operations to identify situations, if any, when hygienic practices in addition to those required by
21 CFR 112.32(b) are necessary to protect against contamination, as provided in 21 CFR
112.32(a).
Maintaining Adequate Personal Cleanliness
Your personnel who handle covered produce or food contact surfaces during a covered activity
must maintain adequate personal cleanliness to protect against contamination of covered produce
and food contact surfaces. (21 CFR 112.32(b)(1)). Exposed skin, outerwear (e.g., smocks,
aprons, coveralls, hair nets, beard guards, and footwear covers), clothing, and footwear should be
free of filth, debris, and other material, to the extent practical. Outerwear, clothing, and footwear
are likely to accumulate some organic material through the normal course of certain activities for
some job duties. You should identify job duties where the accumulation of soil, organic
material, filth, or other debris or potential sources of contamination occurs, and ensure your
personnel maintain adequate personal cleanliness when later performing other activities where
they can transfer contamination to covered produce or food contact surfaces; this could happen,
for example, if personnel handle waste and then clean the food contact surfaces of equipment.
47

Contains Nonbinding Recommendations
Draft-Not for Implementation
You could, for example, specify certain practices related to outerwear, clothing, and footwear for
personnel performing these duties.
There are several strategies that you can use to prevent outerwear, clothing, and footwear from
contaminating covered produce and food contact surfaces. Personnel who are wearing soiled
clothing upon arrival at the farm could present a source of contamination. Generally, clothing,
footwear, and outer garments should be clean when beginning job duties involving covered
produce or food contact surfaces. You should instruct personnel to use clean outerwear,
clothing, and footwear, and change or remove those items as necessary to prevent contamination
of covered produce and food contact surfaces. You could, for example, establish procedures for
personnel to wear outer garments while handling covered produce or food contact surfaces and
remove them before performing any activities where contamination could occur. You could, for
example, establish procedures for personnel to wear aprons while packaging covered produce,
then remove and properly store the aprons when taking a break, and put them back on upon
returning to packing.
If you establish such procedures, personnel should have access to clean outer garments as
needed, and your procedures should ensure that these outer garments are periodically cleaned
and replaced when they become damaged or can no longer be cleaned. A suitable schedule for
replacing and cleaning outer garments depends on the conditions of their use. You should
designate a supervisor or responsible party to periodically assess the condition of outer garments
to determine whether cleaning or replacement is warranted; and personnel should store outer
garments that are used to prevent contamination of covered produce or food contact surfaces in a
location and manner that protects them from contamination. The storage area should be dry and
protected from the surrounding environment and pests. For example, if personnel wear different
smocks when handling covered produce than those worn when handling waste containers, you
should have separate designated areas for storing smocks worn by personnel when handling
covered produce and for storing smocks worn by personnel when handling waste containers.
Practices that support maintaining personal cleanliness also include regularly bathing and
keeping fingernails trimmed to permit effective removal of material from under and around
fingernails. Generally, personnel should bandage all boils, cuts, and other wounds on exposed
skin, including the hands and wrists. If a worker has a boil, cut, or other wound on their hands,
they should use an impermeable cover, such as a bandage, and wear a glove or finger cot as a
secondary barrier to protect the covered produce and food contact surfaces (i.e., prevent
contamination). We provide additional draft guidance in the section of this chapter titled “Using
Gloves.”
Avoiding Contact with Animals Other Than Working Animals
Your personnel who handle covered produce or food contact surfaces during a covered activity
must avoid contact with animals other than working animals, and take appropriate steps to
minimize the likelihood of contamination of covered produce when in direct contact with
working animals. (21 CFR 112.32(b)(2)). These personnel, while performing covered activities,
should also avoid contact with animal fur, feathers, saliva, skin, and excreta, which can harbor
pathogens (Ref. 22) (Ref. 33) (Ref. 37) (Ref. 104) (Ref. 111) (Ref. 122). In some cases,
proximity to animals can result in the transfer of contamination (Ref. 33) (Ref. 104) (Ref. 111)
48

Contains Nonbinding Recommendations
Draft-Not for Implementation
(Ref. 122), which could be without an individual’s knowledge or awareness, such as when an
animal brushes against a worker’s hands or clothing. In the absence of hygienic practices after
contact with animals, humans can transfer these pathogens from their hands or clothing to
covered produce or food contact surfaces. In some outbreaks, failure to maintain hygienic
practices after human contact with animals were identified as likely contributing factors to the
outbreaks (Ref. 33) (Ref. 111) (Ref. 122).
Personnel should be aware of their proximity to animals. Personnel must wash their hands as
soon as practical after touching animals (21 CFR 112.32(b)(3)(v)), which we discuss in the
section of this chapter titled “Thorough Hand-washing.” Additionally, personnel should
consider the need for other hygienic measures, such as changing clothing or footwear, or using
clean outerwear, as discussed in the section of this chapter titled “Maintaining Adequate Personal
Cleanliness.”
FDA does not expect, suggest, or recommend that you remove animals from your farm. If your
farm uses working animals, you should determine which personnel interact with these animals
and ensure that those personnel minimize the potential for contamination of covered produce and
food contact surfaces. There are several ways that you can minimize the risk of personnel
transferring contamination from working animals to covered produce and food contact surfaces.
You could, for example, ensure that personnel who have direct contact with working animals are
not assigned to duties that involve direct contact with covered produce or food contact surfaces.
As an example of this, you could instruct the individual designated to handle a horse pulling a
harvest cart not to handle the covered produce or food contact surfaces, and assign other
personnel to activities related to loading covered produce in the cart. If you assign personnel to
duties in which they contact both covered produce or food contact surfaces and working animals,
those personnel must wash and dry their hands thoroughly in accordance with 21 CFR
112.32(b)(3) as soon as practical after touching animals or any waste of animal origin (21 CFR
112.32(b)(3)(iv)). To minimize the potential for contamination, you could, for example, separate
such personnel’s job duties in a way that they complete those duties that involve handling
covered produce or food contact surfaces before those that involve handling animals during a
given day. For additional draft guidance on working animals see Chapter 7: Equipment, Tools,
Buildings, and Sanitation (Subpart L), and Chapter 5: Domesticated and Wild Animals (Subpart
I).
Personnel to whom you assign job duties of handling covered produce or food contact surfaces
and working animals should understand your practices and procedures to minimize the potential
for contaminating covered produce and food contact surfaces after contact with animals based on
the requirements of the Produce Safety Rule. You should instruct your supervisors and other
responsible parties on your practices and procedures for personnel to avoid contact with animals
other than working animals. You should direct supervisors or responsible parties, as applicable,
to ensure that personnel consistently implement practices to avoid contact with animals other
than working animals, and minimize the potential for contamination of covered produce after
contact with animals.

49

Contains Nonbinding Recommendations
Draft-Not for Implementation
Thorough Hand-washing
There are specified times when personnel who handle covered produce or food contact surfaces
must wash their hands thoroughly, including scrubbing with soap or other effective surfactant
and running water, and then thoroughly dry their hands. (21 CFR 112.32(b)(3)). Examples of
surfactants include soap and detergents.
You may not use antiseptic hand rubs (i.e., “hand sanitizers”) as a substitute for soap and water.
(21 CFR 112.130(d)). The use of soap and water is an effective method to clean hands (Ref. 29)
(Ref. 59) (Ref. 100) (Ref. 133). Grease, soil, or other material present on hands in a work
environment has been shown to reduce the effectiveness of “hand sanitizers” in eliminating
microorganisms (Ref. 59) (Ref. 100). Antiseptic hand rubs may be used after proper handwashing and drying in accordance with 21 CFR 112.32(b)(3), when the antiseptic hand rub
serves as an additional measure in reducing the number of bacteria on hands relatively free of
grease, soil, and other material.
Personnel should be aware that the greatest concentration of microbes typically exists around and
under the fingernails and this is the most difficult area of the hand to clean (Ref. 89) (Ref. 100).
Fingernail brushes, if used properly, have been found to be effective tools in cleaning this area of
the hand (Ref. 89) (Ref. 100). Adequate hand drying devices include single-service towels (e.g.,
paper towels that are disposed of after each use), single-use towels provided by a sanitary towel
service (i.e., a towel rental service that launders and delivers clean towels), and electric hand
dryers. (See 21 CFR 112.32(b)(3)). Personnel should not use common or shared towels for
drying hands (Ref. 2) (Ref. 69) (Ref. 133).
Personnel who handle covered produce or food contact surfaces must wash their hands:
•

Before starting work. (21 CFR 112.32(b)(3)(i)). Personnel should wash their hands
immediately before beginning activities in which they contact covered produce or food
contact surfaces. For example, a worker could arrive at work and complete activities that
do not involve contact with covered produce or food contact surfaces (e.g., signing in on
a timesheet) before handling covered produce or food contact surfaces. They should
perform these non-food contact activities and then thoroughly wash and dry their hands
before beginning food contact activities.

•

Before putting on gloves. (21 CFR 112.32(b)(3)(ii)). Gloves could collect and transfer
contamination from unwashed hands to covered produce. Washing hands before putting
on gloves could, for example, protect against contamination from one’s hand to the
gloves and then to covered produce or food contact surfaces that the gloves contact (Ref.
133). For this reason, the use of gloves is not a substitute for hand-washing as required
by 21 CFR112.32(b)(3). We provide further draft guidance on glove use in the section of
this chapter titled “Using Gloves.”

•

After using the toilet. (21 CFR 112.32(b)(3)(iii)). Toilet use provides a direct means for
hands to become contaminated with pathogens that a worker could shed. Hand-washing
after toilet use protects against the transfer of pathogens from hands to other surfaces.
You could choose to emphasize the requirement to wash hands after using the toilet by
50

Contains Nonbinding Recommendations
Draft-Not for Implementation
placing at toilet facilities and hand-washing facilities signs and visual aids describing
hand-washing methods. You could consider placing hand-washing facilities in
communal areas immediately outside of each toilet facility. During growing activities
that take place in a fully-enclosed building, and during covered harvesting, packing, or
holding activities, you must provide a hand-washing station in sufficiently close
proximity to toilet facilities to make it practical for persons who use the toilet facility to
wash their hands. (21 CFR 112.129(c)).
•

Upon return to the work station after any break or other absence from the work station.
(21 CFR 112.32(b)(3)(iv)). Absence from the work station includes, for example, taking
a break to eat, drink, or use tobacco; leaving the work station to answer the telephone or
accept a delivery; using the toilet; or changing job duties. During absences, an
individual’s hands can become contaminated because they could contact unsanitary
surfaces (e.g., surfaces of buildings, equipment, or other objects that are not designed or
maintained for food contact; personal food and beverages; toilet facilities; or the worker’s
mouth, nose, hair, or skin). Hand-washing upon returning to the work station helps to
protect against contamination of covered produce and food contact surfaces. For
example, if a worker packing chayote fruit stops to take a waste container to a dumpster
for disposal, the worker must wash their hands before returning to their work station to
continue packing chayote fruit. (See 21 CFR 112.32(b)(3)(iv)).

•

As soon as practical after touching animals (including livestock and working animals), or
any waste of animal origin. (21 CFR 112.32(b)(3)(v)). For example, if a worker handles
a horse pulling a harvest cart, they must wash their hands before handling covered
produce. (See 21 CFR 112.32(b)(3)(v)). We discuss contact with animals by personnel
who handle covered produce or food contact surfaces in the section of this chapter titled
“Avoiding Contact with Animals Other Than Working Animals.”

•

At any other time when the hands may have become contaminated in a manner that is
reasonably likely to lead to contamination of covered produce with known or reasonably
foreseeable hazards. (21 CFR 112.32(b)(3)(vi)). Your personnel should recognize
situations when their hands may become contaminated and when they are required to
wash their hands. Examples of such situations include touching: surfaces of buildings,
components of equipment and tools (e.g., control panels, wheels, handles), or other
objects that are not designed or maintained for food contact, such as outside walls, the
floor, or the ground; objects that have been in contact with the floor; tractors; vehicles;
non-food contact tools (e.g., brooms, shovels); trash, dumpsters, or other waste
containers; or the worker’s nose, mouth, hair, or skin.

Training for your personnel who handle covered produce or food contact surfaces, or who are
engaged in the supervision thereof, must include the hand-washing requirements associated with
21 CFR 112.32(b)(3). (See 21 CFR 112.22(a)(3)). You should emphasize how to recognize
potential sources of contamination and the requirement for personnel to wash their hands after
handling such objects and before handling covered produce or food contact surfaces. You
should also train personnel to be conscientious of contact between their hands and their nose,
mouth, hair, skin, and other parts of the body, which increases the potential to transfer
contamination.
51

Contains Nonbinding Recommendations
Draft-Not for Implementation
You should direct your supervisors and other responsible parties, as applicable, to ensure that
personnel consistently follow practices to wash their hands thoroughly. Supervisors and other
responsible parties should encourage and remind personnel to thoroughly wash and dry their
hands in keeping with your procedures. For example, supervisors or responsible parties could
perform demonstrations, or provide verbal reminders, or provide signs and visual aids at handwashing facilities.
Using Gloves
We are not requiring that your personnel use gloves or that gloves, when used, be of a certain
type (e.g., disposable, cotton, leather, or other types). However, if you choose to use gloves in
handling covered produce or food contact surfaces, the gloves must be maintained in an intact
and sanitary condition and replaced when they can no longer be so maintained. (21 CFR
112.32(b)(4)). Gloves with holes, tears, or cracks are not in an intact and sanitary condition.
Gloves should be clean when personnel using gloves begin job duties involving covered produce
or food contact surfaces.
You should evaluate activities that involve hand contact with covered produce or food contact
surfaces, and determine whether personnel should use gloves. Factors to consider in the
development of your approach to glove use include: type of activity, glove type, likelihood for
contamination of covered produce or food contact surfaces, frequency of glove use, glove
storage, frequency of glove cleaning (if appropriate), and glove replacement (e.g., identifying
and replacing gloves when they are no longer in an intact and sanitary condition).
We recognize that different types of gloves, or no gloves, may be appropriate depending on the
circumstances, and 21 CFR 112.32(b)(4) provides you with the flexibility to choose practices
that are appropriate for your operations. Furthermore, if you choose to use gloves for handling
covered produce or food contact surfaces during covered activities, your personnel must follow
the hand-washing requirements in 21 CFR 112.32(b)(3) before putting on gloves. (See 21 CFR
112.23(b)(3)(ii)).
You should develop procedures for glove storage that personnel should follow when storing
reusable gloves while not in use. Gloves used for activities involving contact with covered
produce or food contact surfaces should be stored separately from those used for other activities,
especially those involving contact with potential sources of contamination (e.g., trash or
manure). For both short- and long-term storage, you should provide a clean, dry environment in
which it is convenient for your personnel to leave the gloves and where the gloves are protected
from contamination. For longer periods of storage, gloves should be stored in a fully or
partially-enclosed building, in a designated area that protects the gloves from contamination. For
example, a farm could provide a table for short-term storage of gloves near a field that is being
harvested so that personnel who temporarily leave the field (e.g., to use the toilet) can place their
reusable gloves on the table until they return to work. At the end of the day, the farm could
specify that personnel return the gloves to a certain work station in a fully enclosed barn where
designated personnel examine, clean, and then store the gloves in a designated cabinet.
You should develop a system to periodically assess the condition of both single-use and reusable
gloves to determine when they need to be replaced or, in the case of reusable gloves, cleaned.
52

Contains Nonbinding Recommendations
Draft-Not for Implementation
Single-use gloves are intended to be used once and disposed of when removed. They should not
be reused. When determining an appropriate frequency for cleaning reusable gloves, you should
consider how the gloves will be used and the potential for them to contaminate covered produce
or food contact surfaces. For example, reusable gloves that are used daily for harvest activities
are likely to need more frequent cleaning than gloves that are used once a month to move pallets.
You should ensure that gloves used for activities that involve handling covered produce or food
contact surfaces are immediately replaced or otherwise appropriately addressed when holes,
tears, or cracks appear. Single-use gloves should be replaced, and reusable gloves cleaned, when
they contact a potential source of contamination, when they are removed from the work station
and not stored in an intact or sanitary condition (e.g., when the worker takes a break or uses the
toilet without storing the gloves according to your procedures), and when the worker changes job
duties. Under some circumstances, it could be appropriate for you to instruct personnel to
change gloves when they become visibly soiled or at a predetermined frequency, even if the
gloves remain in good condition. The frequency you specify (e.g., every two hours) should be
based on the activity in which the gloves are used and the likelihood that they will cause
contamination of covered produce or food contact surfaces.
You should identify activities that involve glove use, if any, and the personnel involved in these
activities. These personnel should understand your procedures on the use of gloves. Your
personnel should understand that hygienic practices involve removing gloves when stopping or
completing activities for which the gloves were intended. For example, if personnel wear
reusable gloves when handling covered produce or food contact surfaces throughout the day,
they should remove those gloves before taking breaks or handling the trash. You should instruct
your supervisors and other responsible parties on your practices and procedures for glove use.
You should direct your supervisors and other responsible parties, as applicable, to ensure that
other personnel follow appropriate practices for glove use. Furthermore, supervisors and
responsible parties should emphasize to personnel hygienic practices related to glove use. You
could also choose to use signs and visual aids to reinforce your practices.
Hand Jewelry
Jewelry can serve as a harborage site for contamination (Ref. 46) (Ref. 142). Hand jewelry such
as rings, bracelets, and watches could collect soil or other materials and the construction of the
jewelry could hinder routine cleaning (Ref. 46) (Ref. 114) (Ref. 133) (Ref. 142). Personnel who
handle covered produce or food contact surfaces must remove or cover hand jewelry that cannot
be adequately cleaned and sanitized during periods in which covered produce is manipulated by
hand. (21 CFR 112.32(b)(5)). You should identify the activities on your farm that involve
manipulating covered produce by hand, which could include hand harvesting, post-harvest
washing, sorting, and packing. For these activities, you should determine an approach to hand
jewelry that aligns with the requirements of 21 CFR 112.32(b)(5). You could choose to specify,
for example, that personnel remove or cover all hand jewelry when manipulating covered
produce by hand, or you could determine, for example, that some hand jewelry can be adequately
cleaned and sanitized and allow that type of jewelry to be worn uncovered when your personnel
manipulate covered produce by hand.

53

Contains Nonbinding Recommendations
Draft-Not for Implementation
Personnel who wear uncovered hand jewelry while manipulating covered produce by hand
should clean around and under any hand jewelry to prevent the jewelry from harboring
contamination. Jewelry that cannot be cleaned and sanitized can be covered using gloves or
sleeve guards, as appropriate. Examples of hand jewelry that is unlikely to be adequately
cleaned and sanitized include rings with adornments or embellishments, including stones and
carving, as well as bracelets and watches (Ref. 47). Note that tears can occur in gloves or other
outer garments, particularly from jewelry with embellishments. Personnel who use gloves
should follow your procedures related to glove use, including replacing torn gloves. We provide
draft guidance on glove use in the section of this chapter titled “Using Gloves.”
Your personnel, including supervisors and responsible parties, should understand your
procedures related to jewelry. You should instruct your supervisors and other responsible parties
on your practices and procedures related to hand jewelry, and you should direct them to ensure
that other personnel consistently follow your procedures related to hand jewelry. You should
instruct your supervisors and responsible parties to observe other personnel when performing
their job duties to determine whether they are implementing these hygienic practices, and to
identify any practices that need to be addressed.
Eating, Chewing Gum, and Using Tobacco Products
Personnel must not eat, chew gum, or use tobacco products in an area used for a covered activity;
drinking beverages is permitted in designated areas. (21 CFR 112.32(b)(6)). You should
instruct your supervisors or responsible parties to observe personnel when performing their job
duties to determine whether they are implementing these hygienic practices, and to identify any
unhygienic practices that need to be addressed.
You should visually assess areas where covered activities are performed to determine where to
locate areas designated for beverages. You should locate these designated areas at a sufficient
distance from covered produce and food contact surfaces so as not to serve as potential sources
of contamination to covered produce or food contact surfaces, such as by spillage of partially
consumed beverages and by personnel drinking beverages (e.g., through hand to mouth contact
or spittle). Locating these designated areas near hand-washing facilities could help to facilitate
hand-washing after breaks for beverage drinking. (See 21 CFR 112.32(b)(3)(iv)).

3. Measures to Prevent Visitors from Contaminating Covered Produce
and Food Contact Surfaces
You must take certain measures to prevent visitors from contaminating your covered produce or
food contact surfaces with microorganisms of public health significance. (See 21 CFR 112.33).
A visitor is any person (other than personnel) who enters your covered farm with your
permission. (21 CFR 112.3). Visitors could include consumers, delivery personnel, vendors, or
others who are touring, conducting business, or observing your farm.
Visitors could enter areas where covered produce is grown, harvested, packed, or held, and
where food contact surfaces are present. As with personnel, visitors can transmit contamination
to covered produce or food contact surfaces. For example, an ill visitor experiencing diarrhea
who does not thoroughly wash their hands after using the toilet could unknowingly transfer
54

Contains Nonbinding Recommendations
Draft-Not for Implementation
pathogens to covered produce or food contact surfaces when later handling blueberries or
harvesting containers during a tour of a blueberry field.
Visitor Awareness of Policies and Procedures
You must make visitors aware of policies and procedures to protect covered produce and food
contact surfaces from contamination by people and take all steps reasonably necessary to ensure
that visitors comply with such policies and procedures. (21 CFR 112.33(a)). In addition, 21
CFR 112.31(a) requires you to take measures to prevent contamination of covered produce and
food contact surfaces with microorganisms of public health significance from any person with an
applicable health condition, including visitors.
You should evaluate the different types of visitors on your farm and their interaction with
covered produce and food contact surfaces, to determine appropriate approaches based on the
requirements of 21 CFR 112.33. You have the flexibility to determine how to make visitors
aware of your policies and procedures to protect covered produce and food contact surfaces from
contamination by people. Depending on your farm’s operations, and the reasons that visitors
typically come to your farm, it could be appropriate for you to develop procedures specific to
different types of visitor activities. You could, for example, specify in your policies and
procedures that visitors or visibly ill visitors cannot access certain areas or operations (e.g.,
harvesting or packing). You should inform visitors of how their health and hygienic practices
while visiting your farm are important to protecting covered produce and food contact surfaces
from contamination. You could provide verbal, written, or graphic instructions, or use a
combination of these. If you use written or graphic instructions on signs or visual aids, these
should be in strategic locations, such as near the entrance or fields designated for visitors at a
“pick your own” farm operation. You or your supervisors or other responsible parties should
communicate the necessary information to visitors as soon as practical after their arrival at your
farm.
There are multiple ways for farms to comply with the requirements of 21 CFR 112.33, including
the following examples:
Example 3a: A farm specifies that for visitors that are likely to contact or be in proximity
to covered produce or food contact surfaces, a supervisor will explain at the beginning of
the visit the importance of health and hygiene, including thorough hand-washing
procedures, and the risk from ill or infected visitors with an applicable health condition
contaminating covered produce or food contact surfaces; their applicable policies and
procedures; and the location of visitor-accessible restrooms and hand-washing facilities.
Example 3b: A farm uses one approach to inform all visitors by placing signs stating
their applicable health and hygiene policies and procedures and the location of visitor–
accessible restrooms and hand-washing facilities. The farm displays this information
where visitors are likely to see and read it at the beginning of a visit, such as near the
entrance of the farm, the visitor-accessible restroom, or areas that visitors access.

55

Contains Nonbinding Recommendations
Draft-Not for Implementation
Example 3c: A farm provides to all visitors handouts that provide their applicable health
and hygiene policies and procedures, and the location of visitor-accessible restrooms and
hand-washing facilities.
Toilet and Hand-Washing Facilities
You must make toilet and hand-washing facilities accessible to visitors. (21 CFR 112.33(b)).
You are not required to provide separate toilet and hand-washing facilities for visitors. Toilet
facilities can include plumbed facilities or portable facilities. Note, however, that the general
requirements that apply to toilet facilities and hand-washing facilities are specified in 21 CFR
112.129 and 112.130, respectively. You should inform visitors of the location of toilet facilities
and hand-washing facilities that are accessible to them.

56

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 4:
Biological Soil Amendments of Animal Origin and Human Waste
(Subpart F)
Any biological soil amendment of animal origin (BSAAO) has the potential to be a route of onfarm contamination of produce (Ref. 73) (Ref. 75) (Ref. 74) (Ref. 84) (Ref. 110) (Ref. 117) (Ref.
140) (Ref. 143). The use of unsafe agricultural practices, particularly involving an untreated
BSAAO, could lead to foodborne illness from the consumption of contaminated produce. 9
This chapter provides draft guidance related to Produce Safety Rule subpart F–Biological Soil
Amendments of Animal Origin and Human Waste. Subpart F contains minimum standards for
BSAAOs, including agricultural teas that are BSAAOs, and human waste to minimize the risk of
contamination and help prevent adulteration 10 of your covered produce when you use BSAAOs.
You may not use human waste for growing covered produce, except sewage sludge biosolids
used in accordance with the requirements of 40 CFR part 503, subpart D, or equivalent
regulatory requirements. (21 CFR 112.53).
This chapter will help you:
1. Determine whether your soil amendment is a BSAAO;
2. Determine whether your BSAAO is “treated” or “untreated;”
3. Determine the appropriate treatment process and associated microbial standard for your
treated BSAAO;
4. Determine how to apply your BSAAO;
5. Determine the requirements for handling, conveying, and storing your BSAAO; and
6. Determine what records to keep related to your treated BSAAO.
Figure 4a is a figure to assist you in determining whether your soil amendment is a BSAAO
and Figure 4b provides the application requirements and minimum application intervals to
help you understand the applicable requirements for your farm.

9

For a more detailed and thorough discussion of the many types, uses, and utility of soil amendments, as well as
human pathogens associated with untreated BSAAOs and how certain treatments may reduce their prevalence,
please consult FDA’s Qualitative Assessment of Risk (QAR). (Ref. 54).

10

Under Section 402 of the FD&C Act.

57

Contains Nonbinding Recommendations
Draft-Not for Implementation
Figure 4a. Determining Whether Your Soil Amendment is a BSAAO

58

Contains Nonbinding Recommendations
Draft-Not for Implementation
Figure 4b. Application Requirements and Minimum Application Intervals (21 CFR 112.56)

1. Determine Whether your Soil Amendment is a BSAAO
You should first determine whether your soil amendment, including an agricultural tea, is a
BSAAO. You should refer to the definitions listed in the Produce Safety Rule (21 CFR 112.3)
that apply to the provisions of subpart F, including the following: soil amendment (SA);
biological soil amendment (BSA); biological soil amendment of animal origin (BSAAO);
manure; agricultural tea; agricultural tea additive; pre-consumer vegetative waste; non-fecal
animal byproduct; stabilized compost; table waste; sewage sludge biosolids; and yard trimmings.
59

Contains Nonbinding Recommendations
Draft-Not for Implementation
Understanding the definitions in 21 CFR 112.3 will help you to accurately classify your soil
amendment. The following are defined terms from 21 CFR 112.3 that are most frequently used
in this draft guidance:
Soil amendment means any chemical, biological, or physical material (such as elemental
fertilizers, stabilized compost, manure, non-fecal animal byproducts, peat moss, perlite,
pre-consumer vegetative waste, sewage sludge biosolids, table waste, agricultural tea and
yard trimmings) intentionally added to the soil to improve the chemical or physical
condition of soil in relation to plant growth or to improve the capacity of the soil to hold
water. The term soil amendment also includes growth media that serve as the entire
substrate during the growth of covered produce (such as mushrooms and some sprouts).
Biological soil amendment means any soil amendment containing biological materials
such as stabilized compost, manure, non-fecal animal byproducts, peat moss, preconsumer vegetative waste, sewage sludge biosolids, table waste, agricultural tea, or yard
trimmings, alone or in combination.
Biological soil amendment of animal origin means a biological soil amendment which
consists, in whole or in part, of materials of animal origin, such as manure or non-fecal
animal byproducts including animal mortalities, or table waste, alone or in combination.
The term “biological soil amendment of animal origin” does not include any form of
human waste.
Agricultural tea means a water extract of biological materials (such as stabilized compost,
manure, non-fecal animal byproducts, peat moss, pre-consumer vegetative waste, table
waste, or yard trimmings), excluding any form of human waste, produced to transfer
microbial biomass, fine particulate organic matter, and soluble chemical components into
an aqueous phase. Agricultural teas are held for longer than one hour before application.
Agricultural teas are soil amendments for the purposes of the Produce Safety Rule.
You can determine whether a soil amendment, including an agricultural tea, is a BSAAO by
determining the nature of the materials (e.g., feedstocks or ingredients) used to prepare them.
Examples of BSAAOs include the following:
•
•
•
•
•
•
•

Treated, stabilized compost (i.e., finished compost), compost ingredients, or intermediary
composting materials that contain materials of animal origin;
Treated mushroom mulch (i.e., finished mulch), spent (i.e., used previously as a BSAAO)
mushroom mulch, mushroom mulch ingredients or intermediary materials that contain
materials of animal origin;
Manure (see 21 CFR 112.3);
Worm castings;
Animal bedding material (e.g., straw) that contains animal excreta;
Grass clippings known to include significant animal excreta;
Table waste (e.g., post-consumer waste, including components that are animal or plant in
origin);

60

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

•

Non-fecal animal byproduct (i.e., solid waste (other than manure) that is animal in origin
(such as meat, fat, dairy products, eggs, carcasses, blood meal, bone meal, fish meal,
shellfish waste (such as crab, shrimp, and lobster waste), fish emulsions, and offal) and is
generated by commercial, institutional, or agricultural operations) (21 CFR 112.3); and
Agricultural tea containing biological materials of animal origin.

2. Determine Whether your BSAAO is “Treated” or “Untreated”
After you have determined that you are using a BSAAO (including an agricultural tea that is a
BSAAO), you should determine whether your BSAAO is “treated” or “untreated.” (See 21 CFR
112.51). The treatment status of your BSAAO determines what application restrictions of the
Produce Safety Rule apply.
Treated BSAAO
For BSAAOs, other than agricultural teas, your BSAAO is “treated” if it was processed to
completion to adequately reduce microorganisms of public health significance in accordance
with the requirements of 21 CFR 112.54. (21 CFR 112.51(a)). The rule does not require you or
your supplier to conduct lot-by-lot microbial testing of treated BSAAOs. If you want to consider
a BSAAO to be “treated,” it must be processed to completion using a treatment process
described in 21 CFR 112.54 that has been validated to meet the relevant microbial standard in 21
CFR 112.55. See the section of this chapter titled “Determine the Appropriate Treatment
Process and Associated Microbial Standard for Your Treated BSAAO” for further draft guidance
on treatment processes.
An agricultural tea that is a BSAAO is “treated” if the biological materials of animal origin used
to make the tea have been processed to completion in accordance with the requirements of 21
CFR 112.54, and the water used to make the tea is not untreated surface water and has no
detectable generic E. coli in 100 ml water. (21 CFR 112.51(a)). Agricultural teas cannot contain
agricultural tea additives if they are to be considered “treated” for purposes of 21 CFR 112.51.
(21 CFR 112.51(b)(5)).
Untreated BSAAO
If a BSAAO is not “treated” in accordance with the requirements of 21 CFR 112.51(a), it is
“untreated.” A BSAAO other than an agricultural tea is untreated if it has not been processed to
completion in accordance with the requirements of 21 CFR 112.54. (21 CFR 112.51(b)). An
agricultural tea is “untreated” if the biological materials of animal origin used to make it have not
been processed to completion in accordance with the requirements of 21 CFR 112.54, or the
water used to make the tea is untreated surface water, or the water used to make the tea has
detectable generic E. coli in 100 mL of water. (21 CFR 112.51(b)). Agricultural tea also is
“untreated” if it was made with biological materials of animal origin that contain an agricultural
tea additive. (21 CFR 112.51(b)(5)).
In addition, a BSAAO is “untreated” if any of the following conditions apply:
•

It is contaminated after treatment;
61

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•

It is combined with an untreated BSAAO component after treatment; or
It is composed, at least in part, of untreated waste that you know, or have reason to
believe, is contaminated with a hazard or has been associated with foodborne illness (See
21 CFR 112.51(b)).

Examples of untreated BSAAOs include:
•
•
•

•
•
•
•
•
•
•
•
•

Bedding materials (e.g., untreated straw, hay, wood chips) containing horse feces that are
not processed to completion in accordance with 21 CFR 112.54 (21 CFR 112.51(b)(1));
“Stockpiled” or “aged” manure that is not processed to completion in accordance with 21
CFR 112.54 (21 CFR 112.51(b)(1));
Cow manure, undergoing turned composting, that has been held at an inadequate
temperature, for an insufficient number of days, or that has not been turned enough (i.e.,
that is not processed to completion in accordance with 21 CFR 112.54) (21 CFR
112.51(b)(1));
Treated BSAAO compost contacted by runoff from a pile of untreated cow manure after
treatment was completed on the compost (21 CFR 112.51(b)(2) and 112.52(c));
Treated BSAAO compost to which bedding materials containing horse feces were added
after treatment was completed on the compost (21 CFR 112.51(b)(3));
Treated BSAAO mushroom mulch collected after use (i.e., spent material) contaminated
with animal excreta during storage;
Agricultural tea made from raw manure (21 CFR 112.51(b)(1));
Agricultural tea made from “stockpiled” or “aged” manure that was not processed to
completion in accordance with 21 CFR 112.54 (21 CFR 112.51(b)(1));
Agricultural tea made from treated BSAAO compost contacted by runoff from a pile of
untreated cow manure after treatment was completed on the compost (21 CFR
112.51(b)(2) and 112.52(c));
Agricultural tea made from treated BSAAO compost to which bedding materials
containing horse feces were added after treatment was completed on the compost (21
CFR 112.51(b)(3));
Agricultural tea made from treated BSAAO compost and either untreated surface water,
or water with detectible generic E. coli in 100 ml of water (21 CFR 112.51(b)(1)); and
Agricultural tea made from treated BSAAO compost to which molasses has been added
as an agricultural tea additive (21 CFR 112.51(b)(5)).

You may manage an untreated BSAAO in several ways:
•
•
•
•

Using it as an untreated BSAAO to grow covered produce (in accordance with the
application restrictions in 21 CFR 112.56(a)(1));
Treating or re-treating it (in accordance with 21 CFR 112.51 and 21 CFR 112.54) to
enable using it as a treated BSAAO to grow covered produce (in accordance with the
application restrictions in 21 CFR 112.56(a)(2) or (3));
Using it in a manner that is not subject to the requirements of 21 CFR Part 112 (e.g.,
using it to grow produce not covered by the Produce Safety Rule or a non-produce crop);
or
Disposing of it in accordance with local, state, and federal requirements.
62

Contains Nonbinding Recommendations
Draft-Not for Implementation

3. Determine the Appropriate Treatment Process and Associated
Microbial Standard for your Treated BSAAO
The Produce Safety Rule establishes application restrictions (application methods and
application intervals) for BSAAOs based on whether they are untreated or treated, and for those
that are treated, based on the level of treatment. (See 21 CFR 112.56). Thus, the level of
treatment you choose for a treated BSAAO will affect the application method you use for the
BSAAO in growing covered produce. See the section of this draft guidance titled “Determine
How to Apply Your BSAAO.”
There are two different levels of treatment (i.e., microbial standards) available for treated
BSAAOs; they appear in 21 CFR 112.55(a) and (b). The treatment level in 21CFR 112.55(a) is
more stringent than the treatment level in 21 CFR 112.55(b). The two microbial standards are
listed below:
•

Figure 4d. 21 CFR 112.55(a) (linked to the treatment processes in 21 CFR 112.54(a)):

For the microorganism -

The microbial standard is -

L. monocytogenes

Not detected using a method that can detect one colony forming unit
(CFU) per 5 gram (or milliliter, if liquid is being sampled) analytical
portion.

Salmonella species

Not detected using a method that can detect three most probable
numbers (MPN) per 4 grams (or milliliter, if liquid is being
sampled) of total solids.

E. coli O157:H7

Not detected using a method that can detect 0.3 MPN per 1 gram (or
milliliter, if liquid is being sampled) analytical portion.

•

Figure 4e. 21 CFR 112.55(b) (linked to the treatment processes in 21 CFR 112.54(b)):

For the microorganism -

The microbial standard is -

Salmonella species

Not detected using a method that can detect three MPN per 4 grams
(or milliliter, if liquid is being sampled) of total solids.

Fecal coliforms

Less than 1,000 MPN per gram (or milliliter, if liquid is being
sampled) of total solids.

63

Contains Nonbinding Recommendations
Draft-Not for Implementation
There are various processes to treat BSAAOs. The Produce Safety Rule describes acceptable
treatment processes in 21 CFR 112.54(a) and (b) for the treatment of BSAAOs to be used for
growing covered produce, provided that the resulting BSAAOs are applied in accordance with
the applicable requirements of 21 CFR 112.56 (See 21 CFR 112.54).
You have the flexibility to determine a treatment process for your BSAAO under 21 CFR
112.54. You can use a physical process (e.g., heat), a chemical process (e.g., high alkaline pH),
a biological process (e.g., composting), or a combination of processes (Ref. 30) (Ref. 137). A
scientifically valid treatment process is an approach based on scientific information, data, or
results, published in, for example, scientific journals, references, text books, or peer-reviewed
literature, or contained in proprietary research.
Validation Studies
Validation studies are used to demonstrate that treatment processes meet the applicable microbial
standards. A treatment process must be validated to satisfy one of the two microbial standards
contained in 21 CFR 112.55. (See 21 CFR 112.54). The validation studies upon which you rely
may use any analytical method if the testing methods meet the sensitivity requirements (i.e.,
detection threshold) specified in 21 CFR 112.55. FDA does not expect farms to perform
validation studies related to BSAAO treatment processes; however, farms should ensure that the
treatment processes they use have been validated to meet the standards of the Produce Safety
Rule. You could, for example, work with technical assistance resources, such as your BSAAO
suppliers, academia, extension services, and industry associations to assist you with evaluating
validation studies and your practices.
Two examples of scientifically valid, controlled biological (e.g., composting) treatment
processes that meet the microbial standard in 21 CFR 112.55(b) are provided in 21 CFR
112.54(b)(1) and (b)(2), so no further validation of these treatments is necessary. Although 21
CFR 112.54(b)(1) and (b)(2) provide two example processes that you may use to satisfy the
microbial standard in 21 CFR 112.55(b). These are not the only means of achieving composting
treatments that meet the microbial standard in 21 CFR 112.55(b), and we do not discourage you
from using other processes that meet the requirements of 21 CFR 112.54.
Validation studies should:
•
•
•
•
•
•
•

Adequately examine the treatment process and its ability to consistently and predictably
meet the required microbial standard;
Consider the types of materials that will be used;
Consider the density of the materials;
Consider the potential for non-homogeneous material;
Consider the amount of material to be treated;
Consider the relevant environmental conditions (e.g., temperature, humidity, and
precipitation, as could be impacted by regional or seasonal influences);
Include multiple repetitions of microbial testing performed using a statistically valid
sampling plan to verify that the treatment process will consistently produce a BSAAO
that meets the microbial standard; and
64

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

Outline the parameters (e.g., time, temperature, pH, moisture, number and timing of
turnings, carbon:nitrogen ratio) to be controlled, and the acceptable limits or ranges for
those parameters, in order to achieve the microbial treatment levels.

The body of validation data used should demonstrate that the selected parameters are likely to be
effective under production conditions similar to those used at the treatment site. Materials that
are non-homogeneous could contain particles that react differently (e.g., heat at different rates)
during the process. Pathogens could be insulated (i.e., protected) within denser BSAAO
material, which means that less homogeneous materials could require more intense treatment to
meet the microbial standard. In some cases, pilot scale studies may not be indicative of
biological responses at a larger production scale. Process validation is critical to ensuring that a
treatment process will consistently achieve the specified standards.
Processes to Treat BSAAOs
You must ensure that the treatment is processed to completion (See 21 CFR 112.51). You
should:
•
•
•
•

Establish procedures to ensure delivery of the scientifically valid, controlled process
throughout the BSAAO;
Administer the treatment process in a controlled manner to ensure that the treatment
parameters (e.g., time, temperature, moisture content, pH) established during validation
are achieved throughout the entirety of the BSAAO material;
Ensure that the BSAAO is sufficiently homogenized during the treatment process, as
applicable (e.g., blending or turning a compost pile); and
Ensure that the treatment parameters are achieved in areas of the material where delivery
of the process could be more challenging to achieve, such as the bottom or edges of the
pile (e.g., adding a blanket of straw for insulation; appropriate number and placement of
thermometers).

With respect to processing the BSAAO to completion using the example of turned composting
under 21 CFR 112.54(b)(2), consider that every compost pile has a unique size, shape, and
material (i.e., feedstocks or ingredients) composition, all of which affects how the pile will
generate and maintain heat. For example, many compost windrows will reach 131°F (55°C)
relatively quickly, at which time the operator will begin monitoring the days above this
temperature toward meeting the fifteen days of exposure to 131°F (55°C) per 21 CFR
112.54(b)(2). The operator will typically manage both oxygen and nutrients via turning, and, in
some situations, moisture, to maintain the 131°F (55°C) temperature for a total of 15 days.
Turning the piles also serves the purpose of maximizing exposure of the compost material to the
elevated temperatures. To ensure exposure to the 131°F (55°C) temperature, specified in the
example treatment provided in 21 CFR 112.54(b)(2), a minimum of 5 turnings are specified, but
we do not specify a timeframe for each of the turns. Certain factors, such as windrow size or
shape, or material composition or density, could influence the appropriate timing for turning.
The treatment processes provided in 21 CFR 112.54(b)(1) and (b)(2) include adequate curing as
the final component. “Curing” is defined at 21 CFR 112.3. Curing is an important and necessary
step to produce treated, stabilized compost (Ref. 35) (Ref. 40).
65

Contains Nonbinding Recommendations
Draft-Not for Implementation

4. Determine How to Apply your BSAAO
The requirements for application of your BSAAO are linked to whether it is treated or untreated,
and, when treated, based on the level of treatment it received. (See 21 CFR 112.56). To
determine how to apply your BSAAO, you should consider the following factors:
•
•
•
•

•

•
•
•
•

Whether the BSAAO is treated or untreated;
If treated, the level of treatment the BSAAO received;
Based on the BSAAO’s treatment status and level of treatment (if applicable), the
resulting application restrictions provided by the Produce Safety Rule;
The application methods that you could use and the likelihood of contact between the
BSAAO and the harvestable or harvested part of the crop (e.g., broadcast application
usually results in contact with covered produce; some other methods, such as injection or
manual application, are less likely to result in contact);
Practices you could use after application and the likelihood of contact between the
BSAAO and the harvestable or harvested part of the crop (e.g., incorporation into the soil
or application of plasticulture prior to planting usually reduces the likelihood of contact
with covered produce that grows above the ground);
The type of covered produce (e.g., grows in the ground, grows low to the ground, grows
high above the ground);
The maturity of the covered produce at the time of application (e.g., whether the
harvestable or harvested part is present at time of application);
The location of growing area where the BSAAO is applied with respect to surrounding
growing areas (e.g., covered produce in fields adjacent to a field where the BSAAO is
applied); and
The environmental conditions that could impact movement of BSAAO particulates.

We provide examples throughout this section to illustrate potential approaches for the application
of BSAAOs given the requirements of 21 CFR 112.56; we also identify specific covered produce
in these examples for illustrative purposes. Even if you use similar practices for the specific
covered produce mentioned in these examples, you should evaluate your farm’s specific
conditions and practices, such as through a visual assessment, to determine compliance with the
regulatory requirements.
Untreated BSAAO
Untreated BSAAOs must be applied in one of two ways:
•
•

Application in a manner that does not contact covered produce during application
and minimizes the potential for contact with covered produce after application; or
Application in a manner that does not contact covered produce during or after
application. (21 CFR 112.56(a)).

The two methods of application are the same regarding contact with covered produce during
application of the BSAAO. These two application methods for untreated BSAAOs are different
because the second type of application does not involve contact with covered produce after
66

Contains Nonbinding Recommendations
Draft-Not for Implementation
application of the BSAAO. The minimum application interval (i.e., interval between application
of the BSAAO and harvest) specified for each method of application is discussed in the section
of this chapter titled “Minimum Application Interval.”
Contact with Covered Produce During Application
Untreated BSAAOs must be applied in a manner that does not contact covered produce during
application. (See 21 CFR 112.56(a)(1)(i) and 21 CFR 112.56(a)(1)(ii)). This means there is no
intended or likely contact between the untreated BSAAO and the harvestable or harvested part of
the crop during application. Your evaluation of your farm’s practices should assist you in
determining how to apply your BSAAO based on this requirement. You should consider the
factors listed in the introduction of this section to determine how to apply your untreated
BSAAO.
Some application methods result in BSAAOs contacting the covered produce during application,
and therefore cannot be used to apply untreated BSAAOs when the harvestable or harvested part
of the crop is present during application. Certain methods, such as broadcast application with
any crop or mechanical side-dressing with crops growing on or near the ground, result in contact
between the untreated BSAAO and the harvestable or harvested part of the crop during
application.
Example 4a: If a farm applies an untreated BSAAO using a broadcast spreader (i.e.,
application throughout the field) while the harvestable or harvested part of the crop is
present, widespread contact between the BSAAO and the crop would occur during
application.
You must not place, spread, or spray the untreated BSAAO in such a way that it contacts the
harvestable part of your covered produce during application. (See 21 CFR 112.56).
Example 4b: If, for example, a farm manually applies (e.g., with a shovel) an untreated
BSAAO to the soil used to grow a crop growing high above the ground (e.g., pistachios)
when the harvestable or harvested part is present, the untreated BSAAO would not
contact the pistachios during application when properly applied.
Contact with Covered Produce After Application
You must apply untreated BSAAOs so that, after application of the BSAAO, either (1) the
BSAAO does not contact covered produce, or (2) the potential for contact with covered produce
has been minimized. (See 21 CFR 112.56(a)).
As discussed above (regarding contact during application), to meet the requirement that the
BSAAO does not contact covered produce after application, there is no intended or likely contact
between the BSAAO and covered produce during the relevant time period (in this case, after
application). In Example 4b, if the pistachios were harvested without dropping the pistachios to
the ground and there was otherwise no contact between the pistachios and the ground during
growing or harvesting, then contact between the untreated BSAAO and the harvestable or
harvested part of the pistachios after application is not intended or likely (i.e., it meets the
67

Contains Nonbinding Recommendations
Draft-Not for Implementation
requirement that the BSAAO does not contact covered produce after application). This is the
case even if there was some remote potential for the BSAAO to contact the harvestable or
harvested part of the covered produce (e.g., particles to be lifted by the wind to the height of the
harvestable or harvested part of the pistachios after applying the BSAAO to the soil). There is
always a chance that some soil amendment could be present in dust such that it settles on
covered produce; however, we do not believe at this time that this type of potential contact is
significant enough to be considered intended or likely for purposes of 21 CFR 112.56.
“Minimize the potential for contact” means there is no intended contact between the BSAAO and
covered produce during the relevant time period, but some unintentional contact is likely due to
incidental or environmental action.
Example 4c. If a farm applies untreated manure on top of the soil prior to planting a field
of green beans, while there would be no intended contact between the untreated BSAAO
and the harvestable or harvested part of the crop after application, some unintentional
contact between the untreated manure and the harvestable or harvested part of the green
beans could occur because the manure could be carried by splash to the green beans
during heavy rains. The farm’s procedures include that during growing, the green bean
plants will be attached to stakes to assist in minimizing the potential for contact between
the harvestable or harvest part of the crop and the BSAAO after application.
Example 4d: There would be no intended contact after application for an untreated
agricultural tea applied pre-planting as a drench or spray onto the soil for growing
cauliflower; however, some unintentional contact between the untreated BSAAO and the
harvestable or harvested part of the cauliflower could occur as a result of splash during
heavy rains between the BSAAO and the cauliflower after application. In the farm’s
evaluation of factors, the harvestable or harvested part of the cauliflower is not present
until several weeks after application, the covered produce grows above the ground with
surrounding outer leaves, and the farm determined that rain events are infrequent during
the growing and harvesting seasons.
In some cases, contact is both intentional and likely.
Example 4e: If a farm incorporates an untreated BSAAO into the soil immediately prior
to planting for the production of a root crop, this would cause the untreated BSAAO to
contact the root crop after application (e.g., during growing). In this example, contact
between the covered produce and the untreated BSAAO after application is both
intentional and likely to occur and its application does not meet the requirements for
untreated BSAAO under 21 CFR 112.56(a).
Minimum Application Interval
The minimum application interval of an untreated BSAAO that is applied in a manner that does
not contact covered produce during or after application is zero days. (21 CFR 112.56(a)(1)(ii)).
A minimum application interval of zero days means that harvesting of the covered produce can
occur on the same day that the untreated BSAAO is applied.

68

Contains Nonbinding Recommendations
Draft-Not for Implementation
FDA has not determined the minimum application interval for untreated BSAAOs that are
applied in a manner that does not contact covered produce during application and minimizes the
potential for contact with covered produce after application. FDA reserved the provision that
provides the minimum application interval of untreated BSAAO that is applied in a manner that
does not contact covered produce during application and minimizes the potential for contact with
covered produce after application. (21 CFR 112.56(a)(1)(i)). As a result, the requirements for
the minimum application interval for untreated BSAAOs under 21 CFR 112.56(a) do not differ
as of the date of publication of this draft guidance. We are deferring action on an application
interval until we pursue certain steps, including a risk assessment and further research.
We acknowledge that many organic growers currently employ the National Organic Program
(NOP) standard of 90 days or 120 days, as specified in 7 CFR 205.203(c)(1), and we recognize
that such growers will likely continue to use this standard for organic crop production. We do
not object to growers’ use of a 90 or 120 day application interval for untreated BSAAOs subject
to 21 CFR 112.56(a)(1)(i). We believe adherence to a 90 or 120 day application interval to be a
prudent step toward minimizing the likelihood of contamination while the risk assessment and
further research occur.
Treated BSAAO
For BSAAOs that undergo treatment processes that meet the requirements of 21 CFR 112.54(a)
(that is, they meet the more stringent level of treatment in the Produce Safety Rule), you may
apply the treated BSAAO in any manner, and the minimum application interval is 0 days. In
other words, you do not need to apply the BSAAO in a manner that does not contact covered
produce either during or after application of the BSAAO or that minimizes the potential for such
contact. Additionally, covered produce can be harvested immediately after application of the
BSAAO. (21 CFR 112.56(a)(3)). If you apply your treated BSAAO agricultural tea as a soil
amendment in a manner that is intended or likely to contact (e.g. through splash, spray or
leeching) your covered produce during or after application, the BSAAO used to prepare it must
be treated to meet the requirement of 21 CFR 112.54(a). (See 21 CFR 112.56(a)(3)).
For BSAAOs that undergo treatment processes that meet 21 CFR 112.54(b) (that is, they meet
the less stringent level of treatment in the rule), you must apply the treated BSAAO in a manner
that minimizes the potential for contact with covered produce during and after application; and
the minimum application interval is 0 days, which means covered produce can be harvested
immediately after this BSAAO is applied. (21 CFR 112.56(a)(2)).
Example 4f: A farm chooses to side-dress a leafy green crop with a treated BSAAO
compost that meets 21 CFR 112.54(b) (a BSAAO treated to meet the less stringent level
of treatment in the rule) along the base of planted crop rows, either by manual application
or by using specialized equipment to target application to the soil (e.g., at the base of a
raised bed), which results in minimizing the potential for contact of the treated compost
with the crop. In this example, after application of the treated BSAAO, some limited
potential for contact between the untreated BSAAO and the leafy green crop exists due to
incidental or environmental action, such as by splash during heavy rains, but such
contact, nonetheless, is generally minimized. The farm determines that rain events are

69

Contains Nonbinding Recommendations
Draft-Not for Implementation
infrequent during the growing and harvesting seasons, and the farm’s procedures include
removal of outer leaves during harvest.
Example 4g: For a treated BSAAO agricultural tea that meets 21 CFR 112.51(a) and
112.54(b)) if a farm applies the treated BSAAO agricultural tea by side-dressing the soil
(via hand sprayer or soil drench) for broccoli plants prior to flowering, some limited
potential for contact exists between the untreated BSAAO and the harvestable or
harvested part of the broccoli after application by splash during heavy rains, but such
contact, nonetheless, is generally minimized. In the farm’s evaluation of factors, the
broccoli grows above the ground with surrounding outer leaves, and the farm determines
that rain events are infrequent during the growing and harvesting seasons.
Some application methods for BSAAOs do not minimize the potential for contact with covered
produce during application and therefore should not be used for BSAAOs unless they have been
treated to meet the more stringent standard in the rule. That is, they can be used for BSAAOs
that meet 21 CFR 112.54(a) but not for BSAAOs that only meet the treatment requirements of 21
CFR 112.54(b).
Example 4h: If the farm in Example 4f instead applied the treated BSAAO using a
broadcast spreader (i.e., application throughout the field) while the harvestable or
harvested part of the crop was present, it could be reasonably expected that there would
be widespread contact between the BSAAO and the harvestable or harvested part of the
leafy greens during application (as well as after application).
The following figure summarizes requirements of 21 CFR 112.55 and 112.56, as applicable, for
treated BSAAOs.
Figure 4f. Microbial Standards and Application Requirements for Treated BSAAOs.
BSAAO
Treatment
Process
(§ 112.54)

§ 112.54(a) –
Scientifically
Valid Treatment
Process to meet §
112.55(a)5
§ 112.54(b) –
Scientifically
Valid Treatment
process to meet §
112.55(b)6
1

BSAAO
Microbial
Standards
(§ 112.55)
for
L. monocytogenes

Not

detected1

BSAAO
Microbial
Standards
(§ 112.55)
for
Salmonella

Not

detected2

BSAAO
Microbial
Standards
(§ 112.55)
for
E. coli O157:H7

Not

detected3

BSAAO
Microbial
Standards
(§ 112.55)
for
Fecal Coliforms

Not Applicable

BSAAO
Application
(§112.56)

BSAAO
Application
(§112.56)
Minimum
Interval

Any manner
(no restrictions)

0 Days

(§ 112.56(a)(3))

Not Applicable

Not detected2

Not Applicable

<1,000 MPN per
gram (total
solids)4

Minimizes
potential contact
during and after
application
(§ 112.56(a)(2))

Using a method that can detect 1 CFU per 5 grams (or milliliter, if liquid is being sampled) analytical portion.

70

0 Days

Contains Nonbinding Recommendations
Draft-Not for Implementation
2

3
4
5
6

Using a method that can detect 3MPN Salmonella species per 4 grams (or milliliter, if liquid is being sampled) of total
solids.
Using a method that can detect 0.3 MPN per 1 gram (or milliliter, if liquid is being sampled) analytical portion
Per milliliter (if liquid is being sampled) of total solids (dry weight)
See figure 4d.
See figure 4e.

5. Determine the Requirements for Handling, Transporting, and Storing
your BSAAO
The requirements of 21 CFR 112.52 state how you must handle, convey, and store BSAAOs.
You should carefully evaluate your handling, transport, and storage practices for your BSAAOs
(both treated and untreated) for the potential to contaminate your growing areas, water sources,
water distribution systems, other soil amendments (including treated BSAAOs), areas used for
covered activities, covered produce, and food contact surfaces. (See 21 CFR 112.52(a)). During
your evaluation, you should remember that untreated BSAAOs include incomplete or partially
treated BSAAOs and re-contaminated BSAAOs.
You should evaluate your storage practices and the location of your BSAAOs to determine
whether they are managed in a way that they do not become a potential source of contamination.
You should not store these materials in locations where runoff (e.g., from rain or intentionallyadded water) could cause contamination of covered produce growing, harvesting, packing, or
holding areas, agricultural water sources, or other soil amendments. You, for example, could
address this concern through the implementation of runoff controls (e.g., buffer strips or
catchment ditches to divert or absorb any runoff) or with physical containment systems (e.g.,
concrete block walls, soil berms, pits, or lagoons) to prevent runoff.
You must handle, convey, and store any treated BSAAO in a manner and location that minimizes
the risk of it becoming contaminated by untreated or in-process BSAAOs. (21 CFR 112.52(b)).
You should also take measures to reduce the potential for your stored, treated BSAAO to become
contaminated from sources other than BSAAOs, such as from wildlife intrusion and runoff from
adjacent land. To minimize the risk of it becoming contaminated, you could consider selecting
storage locations where the treated BSAAOs are unlikely to contact untreated BSAAOs,
covering the treated BSAAO with a tarp when the location is not subject to runoff, or storing it in
an enclosed building. You should ensure that your personnel are aware of potential sources of
contamination and periodically assess storage areas for sources of contamination. If your treated
BSAAO becomes contaminated, you must handle, convey, and store as if it were untreated. (See
21 CFR 112.52(c)).
You should evaluate how you and your personnel use equipment and tools (e.g. shovels, front
end loaders, windrow turners) for handling BSAAOs to minimize the risk of contamination from
an untreated BSAAO to a treated BSAAO. You should consider whether the equipment that you
use to handle treated BSAAOs (including agricultural teas that are BSAAOs) are also used to
handle untreated BSAAOs, which could result in contamination. You should ensure that your
personnel use practices that minimize the risk of this contamination. For example, you could use
dedicated equipment and tools for activities involving contact with treated BSAAOs, limiting
their use only for contact with treated BSAAOs. You also, for example, could clean and sanitize
equipment and tools previously used with untreated BSAAOs before use with treated BSAAOs.
71

Contains Nonbinding Recommendations
Draft-Not for Implementation
Personnel who handle BSAAOs, supervisors, and responsible parties should understand the
potential routes of contamination associated with BSAAOs, your practices and procedures, and
how to take appropriate corrective measures when they observe conditions that could lead to
contamination. You should direct your supervisors or other responsible parties, as applicable,
with ensuring that your personnel consistently implement practices and procedures related to
BSAAOs based on the regulatory requirements.

6. Determine What Records to Keep for your Treated BSAAO
For treated BSAAOs that you acquire from a third party, you are required to maintain
documentation, at least annually, that (1) the process used by your supplier to treat the BSAAO
is a scientifically valid process that has been carried out with appropriate process monitoring
(e.g., monitoring of time/temperature, moisture content, and pH); and (2) the BSAAO has been
handled, conveyed, and stored in a manner and location to minimize the risk of contamination by
an untreated or in-process BSAAO. (See 21 CFR 112.60(b)(1)). One example of such
documentation is a Certificate of Conformance, provided at least annually, that certifies that
these conditions will be met.
For example, a farm that receives a treated BSAAO from a third party could keep a record that
includes a statement such as: “A scientifically valid thermal treatment was applied and carried
out with appropriate process monitoring to satisfy the microbial standard in 21 CFR 11.55(a).
The BSAAO has been handled, conveyed, and stored in a manner and location to minimize the
risk of contamination.” In addition, other information related to producing or managing the
BSAAO, such as the BSAAO materials used, process parameters monitored and their results, and
any applicable test results could be included.
For a treated BSAAO that you produce for your own covered farm(s), you must establish and
keep documentation that the process controls (for example, time, temperature, and turnings) were
achieved. (See 21 CFR 112.60(b)(2)). You should evaluate your farm’s specific processes to
determine the documentation necessary to comply with the requirements of 21 CFR
112.60(b)(2).
Such documentation for treated, turned compost could include, for example:
•
•
•
•
•

a log book that lists the following: the date that composting began; the nature of the
materials(s) (e.g., a compost that contains raw cow manure);
the carbon:nitrogen ratio of the materials (e.g. 25-30:1); the temperature profile (date,
time, and location of each temperature measurement);
the date and time of each turning event; the date and results of moisture content and pH
determinations;
the date of any addition of water; the date insulation (if any) was added and the means of
insulation (e.g., three-inch layer of straw over pile); and
the end date of the composting and curing processes.

Note that this list is for illustrative purposes only, and would not be applicable in all cases.

72

Contains Nonbinding Recommendations
Draft-Not for Implementation
If, for example, a farm receives from a third party a treated BSAAO that will be subject to
further treatment processes on the farm, the farm could choose to obtain from the third party
documentation about the process used to treat those BSAAOs, and how they were handled,
conveyed, and stored. In this example, the farm must keep records for the treated BSAAO
produced on their covered farm (21 CFR 112.60(b)(2)). We provide additional draft guidance on
general records requirements in Chapter 8: Records (Subpart O).

73

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 5:
Domesticated and Wild Animals (Subpart I)
Domesticated and wild animals are sources of pathogens (Ref. 107) (Ref. 113) (Ref. 139) (Ref.
143) that can transmit foodborne disease through the contamination of produce (Ref. 60) (Ref.
77) (Ref. 86) (Ref. 90) (Ref. 117). Even domesticated companion animals, such as dogs and
cats, can carry pathogens that could be transferred to humans (Ref. 31) (Ref. 111), including
Salmonella spp. (Ref. 6) (Ref. 129) and pathogenic strains of E. coli (Ref. 13) (Ref. 103).
Furthermore, pathogens associated with animal sources (e.g., animal excreta) (Ref. 110) (Ref.
113) (Ref. 141) can survive for prolonged periods of time in the environment where they are
deposited, such as in soil and water (Ref. 109). In this chapter, we use specific animals (e.g.,
cows, dogs, swine, birds, and deer) as examples to provide draft guidance on protecting covered
produce from contamination by animals; the animals used in the examples are not the only
animals that can be a potential source of contamination of covered produce.
The Produce Safety Rule does not authorize the “taking” of threatened or endangered species as
that term is defined by the Endangered Species Act (16 U.S.C. 1531-1544) (i.e., to harass, harm,
pursue, hunt, shoot, wound, kill, trap, capture, collect, or to attempt to engage in any such
conduct). Further, the Produce Safety Rule does not require covered farms to take measures to
exclude animals from outdoor growing areas, or to destroy animal habitat or otherwise clear farm
borders around outdoor growing areas or drainages. (21 CFR 112.84.) We recognize and
support the longstanding co-location of animals and plant food production systems in agriculture,
and do not prohibit animals from covered farms.
The requirements of subpart I are science-based minimum standards regarding the potential for
domesticated or wild animals to contaminate covered produce, and are reasonably necessary to
minimize the risk of serious adverse health consequences or death from covered produce. These
standards address the potential for biological hazards to be introduced by your own domesticated
animals, by domesticated animals from a nearby area, or by wild animals. The requirements of
subpart I apply only when covered activities occur in outdoor areas or partially-enclosed
buildings and when, under the circumstances, a reasonable probability exists that animals will
contaminate covered produce; they do not apply when a covered activity takes place in fullyenclosed buildings or to fish used in aquaculture operations. (See 21 CFR 112.81.)
This chapter will help you:
1. Determine whether, under the circumstances, there is a reasonable probability that
animals will contaminate your covered produce;
2. Assess the relevant outdoor areas and partially-enclosed buildings (i.e., relevant areas) on
your farm for evidence of potential contamination of covered produce by animals; and
3. Evaluate significant evidence of potential contamination of covered produce by animals
to determine whether harvest can occur.
There are other requirements of the Produce Safety Rule that relate to animals. Draft guidance
on those requirements can be found in the following chapters and sections of this document:

74

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•

Chapter 3: Health and Hygiene (Subpart D) sections titled “Avoiding Contact with
Animals Other Than Working Animals” and “Thorough Hand-washing”;
Chapter 6: Growing, Harvesting, Packing, and Holding Activities (Subpart K) section
titled “Identifying and Not Harvesting Contaminated Covered Produce”; and
Chapter 7: Equipment, Tools, Buildings, and Sanitation (Subpart L) sections titled
“Domesticated Animals”; “Pest Control”; and “Animal Excreta and Litter from
Domesticated Animals.”

1. Determining Reasonable Probability That Animals Will Contaminate
Covered Produce
To determine whether subpart I applies to you, you should:
•
•

Identify outdoor areas and partially-enclosed buildings on your farm where covered
activities occur during the growing season; and
Determine whether, under your specific circumstances, there is a reasonable probability
that animals will contaminate covered produce in these identified outdoor areas or
partially-enclosed buildings during the growing season. (See 21 CFR 112.81and
112.83.)

You should evaluate your farm’s covered produce, conditions, and practices when determining
the probability that animals will contaminate your covered produce in these areas. This should
include an evaluation of the types of animals that could contaminate your covered produce,
based on:
•
•

Available historical observations of animals; and
Other information and factors (e.g., presence of animal attractants or habitats) that could
influence animal presence on or near your farm.

Wild and domesticated animals, including your own domesticated animals and those from a
nearby area, could be sources of contamination for covered produce and food contact surfaces.
Wild and domesticated animals on or near your farm include feral, grazing, and working animals
(e.g., guard dogs), livestock, and pets. You should consider the presence of animal attractants or
habitats on or near your farm (e.g., water and food sources; discarded produce, brush, or waste
piles; wooded areas; areas used for concentrated animal housing or holding, such as animal barns
or feeding operations; and potential nesting areas) that influence the presence of animals. You
should also consider seasonal presence of animals on your farm, such as areas used for resting or
feeding by large numbers of Canada geese or other birds along their migration routes.
In your evaluation, you should also consider land features (e.g., topography), land use, and the
presence of existing measures or structures on or near your farm that affect whether animals (or
their waste) will be present on your farm. This could include features that control runoff
containing animal waste (e.g., ditches, mounds, diversion berms, vegetative buffer strips, or
animal waste containment structures) or other structures that impact your relevant areas. For
example, if you have well-designed and maintained diversion berms that prevent cattle waste

75

Contains Nonbinding Recommendations
Draft-Not for Implementation
runoff from entering your covered produce field, there would not be a reasonable probability that
runoff from the diverted animal waste will contaminate your covered produce in that field.
FDA encourages the application of practices that enhance food safety and that are consistent with
sustainable conservation. We do not expect, suggest, or recommend that farms eliminate animals
from outdoor growing areas. Nor do we require the application of practices that may adversely
affect wildlife, such as removal of habitat or wild animals from land adjacent to produce fields.
If you determine that there is a reasonable probability that animals will contaminate your covered
produce, you must assess the relevant areas used for a covered activity for evidence of potential
contamination of covered produce as needed during the growing season. (See 21 CFR
112.83(b)(1)).
The following examples illustrate how a farm could evaluate their covered produce, conditions,
and practices to determine whether there is a reasonable probability that animals will
contaminate covered produce. These examples are intended to illustrate concepts and are not
intended to be universally applicable. Even if you have circumstances similar to those
mentioned here, you should perform your own evaluation based on your farm’s specific practices
and conditions.
Example 5a: If a farm determines that their growing areas in partially-enclosed shade
houses for Swiss chard are not located near animal attractants or habitats, and there have
been no observations of animals with the potential to contaminate covered produce in
these houses, then there is no reasonable probability that animals will contaminate the
Swiss chard.
Example 5b: If a farm determines that their outdoor growing areas for mustard greens
are near a pond that is a habitat for water fowl, and the water fowl and their excreta are
frequently observed in the outdoor mustard greens growing areas, then there is a
reasonable probability that the water fowl will contaminate those mustard greens.
You should periodically re-evaluate your farm’s conditions and practices. Changes on or near
your farm could impact the probability that animals will contaminate your covered produce.
Certain temporary or unusual conditions could influence whether there is a reasonable
probability that animals will contaminate your covered produce. Construction or cultivation on
or near your farm, or weather events (Ref. 102), such as heavy rains, droughts, or fires (Ref. 91),
could alter animal movements or cause atypical or unanticipated animal presence. For example,
during a drought, nearby wild animals could be more likely to enter your farm to access areas
where you hold water, or animals could change their movements to avoid flooded areas during
periods of heavy rainfall. If these events occur, you should determine whether the conditions on
or near your farm have changed in a way that affects a previous determination of whether there is
a reasonable probability that animals will contaminate your covered produce.
We concluded that it is not necessary for farms to apply the requirements of subpart I to covered
produce that grows completely underground because there will not be a reasonable probability of
contamination by animals as a general matter because of the growth habit of such produce;
however, covered produce that grows completely underground is subject to other requirements of
the Produce Safety Rule, as applicable, including 21 CFR 112.112 that requires you to take all
76

Contains Nonbinding Recommendations
Draft-Not for Implementation
measures reasonably necessary to identify and, not harvest, covered produce that is reasonably
likely to be contaminated with a known or reasonably foreseeable hazard.

2. Assessing Relevant Areas for Evidence of Potential Contamination of
Covered Produce
If you determine that there is a reasonable probability that animals will contaminate your covered
produce, you must assess the relevant areas used for a covered activity for evidence of potential
contamination of covered produce as needed during the growing season. (See 21 CFR
112.83(b)(1)). You have the flexibility to assess the relevant areas based on your covered
produce, your practices and conditions, and your observations and experience. (See 21 CFR
112.83(b)(1)). You should develop an approach that will assist you in assessing relevant areas
for evidence of potential contamination of covered produce. Your approach to assessment could
vary depending on the types of animals and other factors you identified in determining whether
there is a reasonable probability that animals will contaminate your covered produce in each
relevant area on your farm.
In your approach to assessment, you should consider the following:
•
•
•

The personnel who are responsible for monitoring the relevant areas;
The timing and frequency of monitoring; and
The reporting of observations of evidence of potential contamination (i.e., how and
when reporting occurs and to whom).

The outcome of your monitoring activities will help you determine whether you need to take any
additional action with respect to your covered produce. Additional action is discussed in the
section of this chapter titled “Evaluating Significant Evidence of Potential Contamination of
Covered Produce by Animals to Determine Whether Harvest Can Occur.”
Developing and Modifying Your Approach to Assessment
You should periodically evaluate your approach to assessment and modify it as needed. There
are several factors you should consider in developing and modifying your approach to
assessment, including:
•
•
•
•
•

The types of animals that you determined have a reasonable probability of
contaminating your covered produce;
The expected numbers of such animals (i.e., animal populations);
The expected frequency of animal activity (e.g., monthly, weekly);
The likely location of animal activity that impacts your relevant areas (e.g.,
nearby attractants or habitats); and
The expected time of day of animal activity (e.g., early morning, dusk).

Factors that influence animal presence, such as the presence of animal attractants or habitats
(e.g., standing water, discarded produce piles, wooded areas, potential nesting areas, and
identified animal pathways) on or near the relevant areas on your farm, should inform where and
how often you monitor these areas. For example, if one of the growing areas you plan to monitor
77

Contains Nonbinding Recommendations
Draft-Not for Implementation
is directly adjacent to a wooded area, that growing area could be more prone to animal activity,
especially along the wood line, and warrant more frequent monitoring than other growing areas
that are not near animal attractants.
You should monitor when animals are more likely to be present in your outdoor areas or
partially-enclosed buildings, which may vary depending on the type of animal. For example, if
your farm is within an animal migratory path (e.g., Canada geese are present during certain times
of the year), your monitoring should occur when the migratory animals are present (e.g., the
Canada geese).
You should consider the potential impact of weather events and other conditions as you evaluate
your monitoring frequency for relevant areas on your farm, and make potential short-term
adjustments as needed. As previously noted, weather events, such as heavy rains, droughts, or
fires could alter animal movements or cause atypical or unanticipated animal presence (Ref. 91)
(Ref. 102). For example, during a drought, if a supervisor observes an increased presence of
animals and excreta during monitoring of growing areas near ponds located on the farm, then the
farm should more frequently monitor the growing areas near ponds during the drought
conditions.
The following examples illustrate how a farm could assess relevant areas for evidence of
potential contamination under 21 CFR 112.83(b)(1) after having made a determination that there
is a reasonable probability that animals will contaminate covered produce. These examples are
intended to illustrate concepts and are not intended to be universally applicable. Even if you
have circumstances similar to those mentioned here, you should perform your own evaluation
based on your farm’s specific practices and conditions.
Example 5c: A farm’s outdoor area used for growing basil is near a pond and a wooded
area that the farm determines is a habitat for several types of wild animals. The farm
personnel observe deer herds and ground squirrels on the farm around the growing areas
throughout the growing season (i.e., more than several occasions), and the farm
determines the growing areas are within animal movement pathways. The farm must
assess these areas for evidence of potential contamination. (See 21 CFR 112.83(b)(1)).
The farm should monitor the outdoor basil growing areas at least twice during the
growing season.
Example 5d: A farm’s outdoor kale growing areas are located near a pond that the farm
determines serves as a water source for deer and ducks, and ducks and their excreta are
observed in the outdoor growing areas one to two times per month (e.g., less frequently
than weekly observations) during the growing season when kale is present. The farm
must assess these areas for evidence of potential contamination (See 21 CFR
112.83(b)(1)). The farm should monitor the outdoor kale growing areas at least monthly
during the growing season.
Example 5e: A farm’s outdoor areas for growing blackberries are located near a barn that
the farm determines attracts birds for nesting. Birds are frequently (at least weekly)
observed in the outdoor growing areas for blackberries, and personnel observed excreta
on blackberries near and during harvesting activities. The farm must assess the
78

Contains Nonbinding Recommendations
Draft-Not for Implementation
blackberry growing areas for evidence of potential contamination (See 21 CFR
112.83(b)(1)). The farm should monitor the outdoor blackberry growing areas at least
weekly.
Performing Monitoring Activities
You should determine which personnel will conduct monitoring and how they are to perform
monitoring. You could, for example, designate a single individual to perform all monitoring
activities, or designate specific individuals to perform these job responsibilities in different areas.
Depending upon your situation, you could assign personnel to perform multiple tasks. For
example, if you determine that there is a reasonable probability that animals will contaminate
your strawberry field and that you need to assess for evidence of potential contamination weekly,
you could direct your personnel who perform weekly weeding in a strawberry field to monitor
for potential contamination of strawberries while they weed the field. You should also ensure
that personnel performing monitoring understand how to identify signs of potential
contamination of covered produce by animals.
Monitoring should include a visual examination for evidence of potential contamination of
covered produce by animals in your relevant areas. Examples of animal activity to consider
when examining for evidence of potential contamination include the presence of significant
numbers of animals, animal excreta, nests, and signs of pecking, feeding, rooting, trampling,
grazing, or bedding. For example, your personnel performing monitoring of partially-enclosed
buildings could look for bird nesting and landing areas in overhead areas, such as the rafters,
eaves, or roof.

3. Evaluating Significant Evidence of Potential Contamination of Covered Produce by
Animals to Determine Whether Harvest Can Occur
If there is significant evidence of potential contamination by animals, you must evaluate whether
the covered produce can be harvested in accordance with the requirements of 21 CFR 112.112
and take measures reasonably necessary during growing to assist you later during harvest when
you must identify, and not harvest, covered produce that is reasonably likely to be contaminated
with a known or reasonably foreseeable hazard. (21 CFR 112.83(b)(2)).
In determining whether evidence of potential contamination is significant, you should consider
the extent of the evidence of potential contamination. A single observation of a few animals
immediately adjacent to covered produce usually does not represent significant evidence of
potential contamination; however, multiple observations of this type reported over time could
result in a determination of significant evidence of potential contamination, especially when
coupled with observations of excreta on, or damage to, covered produce. On the other hand, a
single observation of a large number of animals near covered produce coupled with extensive
animal excreta on or near covered produce or crop damage could be sufficient to lead you to
determine that there is significant evidence of potential contamination of the affected covered
produce.
You must take measures reasonably necessary during growing to assist you later during harvest
when you must identify, and not harvest, covered produce that is reasonably likely to be
79

Contains Nonbinding Recommendations
Draft-Not for Implementation
contaminated with a known or reasonably foreseeable hazard. (See 21 CFR 112.83(b)(2)).
Reasonably necessary measures could include, for example, designating a specific distance
around the area where you found significant evidence of potential contamination during the
growing season and preventing harvest in that entire area (e.g., a ‘no harvest zone’). In some
circumstances, you might identify significant evidence of potential contamination only in a
certain portion of an outdoor area (e.g., a portion of a field rather than the entire field). For
example, if significant quantities of animal excreta are observed in a portion of a field, you could
designate an area around each observation of animal excreta, or block off a single area that
includes all observations of animal excreta to prevent transfer to covered produce, such as by
runoff or splash. The specific distance around the observations of animal excreta will likely vary
by crop, the extent of potential contamination, and other factors. Certain sources, such as
academia, extension services, industry associations, and government agencies could provide
information on this topic to assist in your determination of an effective ‘no harvest’ perimeter or
zone.
The following examples use the principles discussed in this section to illustrate approaches for
determining whether significant evidence of potential contamination by animals exists. For
illustrative purposes, we selected specific covered produce for these examples. These examples
are intended to illustrate concepts, and are not intended to be universally applicable. Even if you
have circumstances similar to those mentioned here, you should perform your own evaluation
based on your farm’s specific practices and conditions.
Examples of monitoring observations that likely are significant evidence of potential
contamination:
Example 5f. Monitoring observations of a flock of geese, crop destruction, and animal
excreta.
A worker observes evidence that a flock of migrating geese has intruded on fields of
lettuce. The worker observes extensive crop damage (e.g., evidence of crop consumption
and gnaw or bite marks) and extensive goose excreta on and near the lettuce, and reports
these observations to a supervisor. The supervisor determines that this represents
significant evidence of potential contamination of the affected lettuce fields and
determines that the covered produce in the affected fields cannot be harvested, in
accordance with 21 CFR 112.112. The farm must take measures reasonably necessary to
assist later during harvest so that they can identify and not harvest the affected produce.
In this case, the farm’s chosen approach is for the supervisor to mark the affected fields
with red flags and to communicate to the appropriate personnel that the affected lettuce
fields will not be harvested.
Example 5g. Monitoring observations of animal excreta.
A worker observes trampled plants, evidence of animal feeding, and animal excreta on
green beans in one field. The worker reports to a supervisor this observation. Workers on
the farm have previously observed raccoons and animal tracks in the same field. The
supervisor determines that these observations are significant evidence of potential
contamination for the field of green beans. The farm must take measures reasonably
necessary to assist later during harvest so that they can identify and not harvest the
affected produce. In this case, the farm’s chosen approach is for the supervisor to mark a
80

Contains Nonbinding Recommendations
Draft-Not for Implementation
portion of the field that includes all affected areas with flags to designate the portion of
the field that will not be harvested and to communicate to the appropriate personnel that
the designated portion of the field will not be harvested. The supervisor also reminds
personnel to watch for evidence of potential contamination during the harvesting of
covered produce.
Example 5h. Monitoring observations of animal excreta.
A worker identifies and reports several piles of dog excreta observed in several areas
during a monthly monitoring event of a zucchini field. The observations indicate that
some of the dog excreta is fresh while some appears to have been present in the field for a
longer time. Some of the dog excreta contacted the zucchini. The farm owner
determines that this observation is significant evidence of potential contamination of a
portion of the zucchini in the field. The farm must take measures reasonably necessary to
assist later during harvest so that they can identify and not harvest the affected produce.
In this case, the farm’s chosen approach is for a designated worker to mark an area
surrounding each observation of dog excreta with flags and to designate that these areas
will not be harvested. The farm owner communicates to the appropriate personnel that
the flags identify areas that should not be harvested; a supervisor also reminds the
personnel to watch for additional evidence of potential contamination during harvest
activities.
Examples of monitoring observations that likely are not significant evidence of potential
contamination:
Example 5i. Observations of animal tracks in an outdoor growing area.
During the growing season, a worker performing monitoring observes a few raccoon
tracks in a recently planted field of green beans. This observation was the only
observation reported for that field of green beans during the growing season. This
contrasts with example 5g where in addition to the observation of animal tracks, there
was also evidence of animal feeding, animal excreta, and trampled plants.
Example 5j. Observations of animal excreta.
A worker reports that they saw several small piles of fresh dog excreta in a small area of
a blueberry field two weeks prior to harvest. The dog excreta did not directly contact the
blueberries. A supervisor confirms that a careful assessment of the entire blueberry field
was conducted, but that no other observations of animal excreta or potential
contamination of covered produce were observed in the field. A supervisor also confirms
that the worker removed the dog excreta from the growing area immediately after the
observation occurred.

81

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 6:
Growing, Harvesting, Packing, and Holding Activities (Subpart K)
Produce is susceptible to contamination during growing, harvesting, packing, and holding
activities (Ref. 17) (Ref. 49) (Ref. 67) (Ref. 90). Adhering to food safety practices during the
day-to-day operations on your farm is critical to protecting covered produce (Ref. 17) (Ref. 34)
(Ref. 67) (Ref. 90) (Ref. 99) (Ref. 121). Where applicable, we recommend evaluating your
relevant procedures, processes, and practices periodically to ensure that you consider the scope
of your relevant activities or operations and any changes that occurred and how they are affected
by and relate to the requirements of the Produce Safety Rule. During such evaluations, you
should consider not only typical practices, but also those that occur infrequently or due to
unusual circumstances, to account for the breadth of procedures, processes, and practices
associated with a given activity.
This chapter provides draft guidance on the requirements of Produce Safety Rule subpart K–
Growing, Harvesting, Packing, and Holding Activities. This subpart is applicable to growing,
harvesting, packing, and holding activities, including the transition points between those phases.
The discussion is divided into: separation of covered and excluded produce; identifying and not
harvesting contaminated covered produce; handling harvested covered produce; dropped covered
produce; packaging covered produce; and food-packing material.

1. Separation of Covered and Excluded Produce
We provide draft guidance on the distinction between covered and excluded produce in Chapter
1: General Provisions (Subpart A) in the sections titled “Covered Produce. Depending on your
farm layout, planting schedule, and growing and harvesting seasons, there could be times when
you grow, harvest, pack, or hold multiple produce crops at the same time and in approximately
the same location. You should evaluate your farm’s activities and produce to determine whether
you grow, harvest, pack, or hold both covered and excluded produce and how you handle any
excluded produce; you should visually assess your farm’s activities to confirm your farm’s
practices.
If all of the following conditions are applicable to your farm:
•
•
•

You grow, harvest, pack, or hold covered produce;
You grow, harvest, pack, or hold produce that is not covered by the Produce Safety Rule
(i.e., excluded produce in accordance with 21 CFR 112.2); and
The excluded produce is grown, harvested, packed, or held in a manner that is not in
accordance with the Produce Safety Rule requirements (21 CFR 112.111);

then you must take measures during covered activities to:
•

Keep covered produce separate from excluded produce (except when placed in the same
container for distribution) (21 CFR 112.111(a)); and

82

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

Adequately clean and sanitize, as necessary, any food contact surfaces that contact
excluded produce before using such food contact surfaces for covered activities on
covered produce (21 CFR 112.111(b)).

If you do not grow, harvest, pack, or hold both covered and excluded produce, or if you grow,
harvest, pack, and hold your excluded produce in accordance with the provisions of the Produce
Safety Rule, then the requirements of 21 CFR 112.111 are not applicable to your farm.
Example 6a: A farm grows, harvests, packs, or holds both radishes (covered produce)
and beets (excluded produce) at the same time.
•

•

If the farm grows, harvests, packs, or holds both radishes (covered produce) and
beets (excluded produce) at the same time, and if the farm grows, harvests, packs,
or holds the beets in accordance with the Produce Safety Rule, then 21 CFR
112.111 does not apply and the farm does not need to ensure that the two crops
are separated during growing, harvesting, packing, and holding, and that you
clean and sanitize, as necessary, any food contact surfaces that contact the beets
before they contact the radishes.
However, if the farm grows, harvests, packs, or holds the beets (excluded
produce) in a way that is not in accordance with the Produce Safety Rule
requirements for covered produce (e.g., if the farm uses a biological soil
amendment of animal origin (BSAAO) and does not follow the applicable
requirements related to the BSAAO found in subpart F), then the farm must
ensure that the two crops are separated during growing, harvesting, packing, and
holding, and that the farm cleans and sanitizes, as necessary, any food contact
surfaces that contact the beets before they contact the radishes, as applicable.
(See 21 CFR 112.111(a) and (b)).

You are not required to keep covered and excluded produce separate when you place them into
the same container for distribution. (21 CFR 112.111(a)). For example, you are not restricted
from selling items such as gift baskets or community supported agriculture (CSA) boxes that
contain both covered and excluded produce, or other non-produce food items. So, you could put
the radishes and beets described in the second bullet of the example above together into a CSA
box for distribution to your CSA customers.
If you are subject to the provisions of 21 CFR 112.111, then you should evaluate your farm’s
practices, including growing, harvesting, packing, and holding activities, to determine how to
separate covered produce and excluded produce. This can involve, for example, separation in
location (i.e., physical space), separation in time, or a combination of both. You should
determine whether activities involving covered and excluded produce occur in the same location
or at the same time, use the same equipment and tools, or involve the same personnel, because
use of the same location, equipment, or personnel (Ref. 17) (Ref. 134) could necessitate changes
to your practices or additional oversight in order maintain separation.
You should identify the location (i.e., physical space) in which the covered and excluded
produce will be grown, harvested, packed, and held. You could, for example, choose to plant
83

Contains Nonbinding Recommendations
Draft-Not for Implementation
covered produce in a location that is physically separate from where you plant excluded produce.
Similarly, you could, for example, choose to designate and maintain different holding and
packing areas or buildings to ensure separation of covered and excluded produce. Depending on
your practices, other strategies could be effective in separating covered and excluded produce.
You should also identify equipment and tools used during growing, harvesting, packing, and
holding of excluded produce that are also used for covered produce. You should pay particular
attention to the food contact surfaces of equipment and tools (e.g., knives and harvest containers)
that could contact excluded produce and then contact covered produce. For example, you could
assign separate equipment and tools to the growing and harvesting of covered and excluded
produce; or you could establish procedures for cleaning and, as necessary, sanitizing equipment
and tools used for excluded produce before using them for contact with covered produce (such
cleaning, and as necessary, sanitizing, is required by 21 CFR 112.111(b) when the same tools are
used in these circumstances, and more generally by 21 CFR 112.123(d)). We provide draft
guidance on cleaning and sanitizing in Chapter 7: Equipment, Tools, Buildings, and Sanitation
(Subpart L).
For packing and holding activities, you could schedule the packing of covered produce before
the packing of excluded produce, using cleaned and, if necessary, sanitized equipment, tools, and
containers for the covered produce. Further, if you choose to pack or hold both covered produce
and excluded produce (that is not grown, harvested, packed, or held in accordance with the
Produce Safety Rule) at the same time, you could consider the following practices to minimize
the risk of contamination of the covered produce:
•
•
•
•

Providing walls, other barriers, or space to separate covered and excluded produce;
Clearly marking packing or holding areas for excluded produce or covered produce;
Clearly marking or color-coding containers to minimize the risk of excluded produce
containers being used for covered produce; and
Establishing procedures for personnel working in the excluded produce packing or
holding areas to ensure separation of excluded produce and covered produce.

You should instruct your supervisors and other responsible parties on your procedures for
separation of covered and excluded produce. Supervisors and other responsible parties should
emphasize and remind personnel to maintain separation of covered and excluded produce based
on the regulatory requirements.
Personnel who handle covered produce or food contact surfaces, or who are engaged in the
supervision thereof, must receive training related to the separation of excluded and covered
produce, as applicable. (See 21 CFR 112.22(a)(3)). Personnel who contact food contact surfaces
for cleaning and, when necessary, sanitizing activities, or who are engaged in the supervision
thereof, must also be trained. (See 21 CFR 112.22(a)(3)). These personnel should understand
your practices for maintaining separation of covered and excluded produce, preparing the
cleaning and sanitizing solutions, when necessary; and when to perform such activities between
handling of excluded and covered produce. We provide further draft guidance on training in
Chapter 2: Personnel Qualifications and Training (Subpart C).

84

Contains Nonbinding Recommendations
Draft-Not for Implementation

2. Identifying and Not Harvesting Contaminated Covered Produce
Immediately prior to and during harvest activities, you must take all measures reasonably
necessary to identify, and not harvest, covered produce that is reasonably likely to be
contaminated with a known or reasonably foreseeable hazard. (See 21 CFR 112.112). The
requirements of 21 CFR 112.112 are intended to be flexible, to allow you to take steps
appropriate for your situation based on those requirements. In this section, we specifically
discuss animal excreta as a potential source of contamination. (See 21 CFR 112.112). You
should consider the possibility of other sources of contamination, such as flooding, that could be
relevant to your particular growing and harvesting conditions, and address those as needed.
Animal excreta represent a source of pathogens (Ref. 78) (Ref. 110) (Ref. 143). Environmental
investigations for certain outbreaks indicated that wild animal excreta were a source of
pathogens linked to the outbreaks, and in some cases were observed in the fields near the time of
harvest (Ref. 60) (Ref. 86) (Ref. 85). Animal saliva, skin, fur, and feathers can also be a source
of pathogens (Ref. 22) (Ref. 33) (Ref. 37) (Ref. 104) (Ref. 111) (Ref. 122). FDA does not
expect, suggest, or recommend that farms eliminate animals from outdoor growing areas.
Instead, the Produce Safety Rule requires farms to take measures reasonably necessary to
identify, and not harvest, covered produce that is reasonably likely to be contaminated with a
known or reasonably foreseeable hazard. This includes taking steps to identify and not harvest
covered produce that is visibly contaminated with animal excreta. At a minimum, your efforts
must include a visual assessment of the growing area and all covered produce to be harvested,
regardless of the harvest method. (See 21 CFR 112.112).
Signs that covered produce is reasonably likely to be contaminated with a known or reasonably
foreseeable hazard include:
•
•
•
•

Excreta observed on the covered produce;
Excreta observed in an area where it is reasonably likely that it has contacted or will
contact nearby covered produce during harvest (see also the discussion in Chapter 5:
Domesticated and Wild Animals (Subpart I));
Animal fur, hair, or feathers observed on the covered produce; and
Crop damage or destruction by animals (e.g., bite/gnaw marks; bent, uprooted, or
trampled crops).

The required visual assessment is most effective when it is performed as close in time before
beginning harvesting as is practicable, under the circumstances of the farm’s operation, or during
harvesting itself. A visual assessment should involve designated personnel visually examining
the entire designated harvest area, including areas that will be mechanically harvested. For large
areas that are mechanically harvested, you should designate personnel to visually assess sections
of the growing area shortly before harvesting activities to identify areas where covered produce
is reasonably likely to be contaminated with a known or reasonably foreseeable hazard.
You must perform visual assessments of the ground above covered produce that is grown
completely underground (e.g., carrots, radishes, jicama). (See 21 CFR 112.112). If, during your
assessment of the growing area and of the underground covered produce during harvest, you see
evidence of animal excreta on or surrounding the covered produce, you must not harvest that
85

Contains Nonbinding Recommendations
Draft-Not for Implementation
covered produce. (See 21 CFR 112.112). If animal excreta are present on the ground above
such covered produce during harvest and would be likely to contaminate the covered produce or
food contact surfaces of harvest equipment, you must not harvest from the affected area. (See 21
CFR 112.112).
Harvest personnel must be trained to recognize covered produce that must not be harvested,
including covered produce that may be contaminated with a known or reasonably foreseeable
hazard. (See 21 CFR 112.22(b)(1)). You should also instruct your harvest personnel to alert
nearby harvest personnel of observations of covered produce that is reasonably likely to be
contaminated with a known or reasonably foreseeable hazard (e.g., visible animal excreta). You
should specify when personnel need to inform a supervisor or other responsible party of
observations of covered produce that is reasonably likely to be contaminated with a known or
reasonably foreseeable hazard so they can determine appropriate steps to ensure that affected
covered produce in the surrounding area is also not harvested.
Your procedures should include necessary actions when evidence of contamination, including
visible animal excreta, is observed. You should inform your supervisors and other responsible
parties of the expected actions and direct them to ensure that these tasks are completed as
needed. You should take the following actions in response to observations of animal excreta, or
other evidence of contamination: identify areas of covered produce that will not be harvested,
such as by cordoning off or otherwise identifying the affected areas; and not harvesting covered
produce that is reasonably likely to be contaminated with a known or reasonably foreseeable
hazard. For example, if during a visual assessment, a worker identifies several clusters of
blackberries that have visible animal excreta on them, then you could, for example, use a visual
marker, such as colored flags, to indicate that they are not to be harvested. You should also
assess whether any other blackberries near the blackberries with the visible contamination are
reasonably likely to be contaminated and take appropriate steps.
As mentioned in Chapter 5: Domesticated and Wild Animals (Subpart I), during the growing
season, you or your personnel could observe significant evidence of potential contamination
when you assess relevant areas required by 21 CFR 112.83(b)(2). Based on those observations,
you could conclude that some growing areas cannot be safely harvested. If you reach such a
conclusion, you must take measures reasonably necessary during growing to assist you later
during harvest when you must identify, and not harvest, covered produce that is reasonably likely
to be contaminated with a known or reasonably foreseeable hazard. (See 21 CFR 112.112). For
example, you could designate a portion of a growing area, so that covered produce in that area is
not harvested, as a result of your observations during the growing season. During harvest, you
must not harvest such covered produce. (See 21 CFR 112.112).

3. Handling Harvested Covered Produce
You must handle harvested covered produce during covered activities in a manner that protects
against contamination with known or reasonably foreseeable hazards. (21 CFR 112.113).
Harvested covered produce is vulnerable to contamination, and handling practices can protect
against contamination (Ref. 36) (Ref. 90).

86

Contains Nonbinding Recommendations
Draft-Not for Implementation
You should evaluate your practices during harvesting, packing, and holding, to identify
conditions that could increase the likelihood of contamination. You should consider the handling
of covered produce by personnel during and after harvest, and the equipment, buildings, and
tools used for covered activities during and after harvest. Based on your evaluation, you should
adjust existing, or implement new, practices to protect harvested covered produce from
contamination during handling, as needed. Practices to consider include: avoiding contact
between the cut surfaces of covered produce and soil, and reducing damage to harvested covered
produce to the extent practical; and packing and holding covered produce in a manner that
minimizes the potential for contamination.
You should establish procedures to ensure that harvesting, packing and holding practices protect
against contamination of covered produce. Personnel who handle covered produce or food
contact surfaces, or who are engaged in the supervision thereof, must receive training related to
handling harvested covered produce, as applicable. (See 21 CFR 112.22(a)(3)). These personnel
should understand your practices to protect harvested covered produce. Furthermore, personnel
you assign to supervise or otherwise be responsible for your operations should ensure that other
personnel consistently implement practices to protect harvested covered produce against
contamination. We provide further draft guidance on training in Chapter 2: Personnel
Qualifications and Training (Subpart C).
Contamination could be transferred to harvested covered produce when contact occurs between
the covered produce, especially at cut surfaces, and the soil. Preventing unnecessary contact
could reduce the likelihood of pathogen transfer (Ref. 36) (Ref. 90). For example, during lettuce
harvest, you should place harvested lettuce heads that have been cut from the root on a clean
surface while waiting for trimming, rather than placing them directly on the soil.
Bruises, punctures, or other injuries to harvested covered produce create potential pathways for
pathogens to contaminate the covered produce and multiply (Ref. 5) (Ref. 4) (Ref. 67).
Personnel should understand which activities will likely result in damage. You could consider
practices to protect against contamination of harvested covered produce through damage, such as
the following:
•
•
•
•

Ensuring harvest containers are free from rough edges or other rigid protrusions;
Avoiding rough handling when transferring covered produce from one container to
another or to a different surface, such as a hopper, table, or belt;
Avoiding overfilling containers, which can crush or damage covered produce;
Ensuring that personnel use equipment and tools consistent with your procedures and in a
way that minimizes damage to covered produce.

4. Dropped Covered Produce
You must not distribute dropped covered produce. (21 CFR 112.114). Dropped covered
produce is produce that drops to the ground before harvest and does not include:
•
•

Root crops that grow underground (such as carrots);
Crops that grow on the ground (such as cantaloupe); or
87

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

Produce that is intentionally dropped to the ground as part of harvesting (such as
almonds). (21 CFR 112.114).

Covered produce is subject to the requirements in 21 CFR 112.114 unless it is specifically
identified as not being included within the meaning of “dropped covered produce” as provided in
21 CFR 112.114. Some covered produce, like almonds, may be intentionally dropped to the
ground as part of harvesting (e.g., by shaking the almond tree). This type of harvesting generally
occurs with produce that have an inedible, hard outer layer, and an edible, relatively durable
inner layer. However, most covered produce, including some with an inedible outer layer or rind
and soft-fleshed, inner layer, can be damaged by the force of the impact when dropped to the
ground. For covered produce crops that typically are not dropped to the ground during harvest,
some could nonetheless fall to the ground, often resulting in damage to or contamination of the
covered produce. This damage may not be visible for several days or weeks. The damage could
introduce or cause an increase of pathogens (Ref. 5) (Ref. 4). For example, peaches that drop
from the tree are likely to impact the ground with a force that can cause damage to the surface of
the fruit and allow for the introduction of pathogens into the flesh of the fruit. Produce that
grows off the ground, such as peaches or tomatoes, and that drops to the ground before harvest is
considered dropped covered produce, even if the produce is still attached to the plant when it
contacts the ground. You should establish procedures that ensure that you do not distribute
dropped covered produce.
Personnel who handle covered produce or food contact surfaces, or who are engaged in the
supervision thereof, must receive training related to dropped covered produce, as applicable.
(See 21 CFR 112.22(a)(3)). You should train your harvest personnel, and personnel you assign
to supervise or otherwise be responsible for your operations, to avoid harvesting dropped
covered produce. These personnel should understand your practices related to dropped covered
produce. Personnel who supervise harvesting, or other responsible parties, should ensure that
personnel who conduct harvesting do not include dropped covered produce with covered produce
that will be distributed. Furthermore, personnel you assign to supervise or otherwise be
responsible for your operations should ensure that other personnel consistently implement
practices to not distribute dropped covered produce. We provide further draft guidance on
training in Chapter 2: Personnel Qualifications and Training (Subpart C).

5. Packaging Covered Produce
You must package covered produce in a manner that prevents the formation of Clostridium
botulinum toxin, if such toxin is a known or reasonably foreseeable hazard (such as for
mushrooms). (21 CFR 112.115). Produce containing C. botulinum toxin could have no visual
indication that toxin is present (i.e., it may not appear contaminated or spoiled), so prevention is
essential (Ref. 26) (Ref. 127). Mushrooms develop C. botulinum toxin when packaged under
certain conditions (Ref. 62) (Ref. 127). Modified atmosphere or other reduced-oxygen
packaging of produce other than mushrooms could present a similar risk for botulinum toxin
formation depending on factors including produce type and respiration rate, pH, water activity,
temperature, oxygen concentrations, initial Cl. Botulinum spore levels, and the presence and
types of other microflora (Ref. 50) (Ref. 62).

88

Contains Nonbinding Recommendations
Draft-Not for Implementation
Most covered produce continues to respire (i.e., breathe) after it is packaged (Ref. 7) (Ref. 120).
If the covered produce is packaged in an oxygen-impermeable film, the continued respiration can
decrease the level of oxygen and increase the level of carbon dioxide within the package,
creating conditions favorable for C. botulinum toxin formation (Ref. 67) (Ref. 127). The
necessary time for toxin formation varies depending upon the temperature and other conditions.
The minimum temperature for C. botulinum growth and toxin formation is 38°F (3.3°C) (Ref.
76) (Ref. 118) (Ref. 123).
If Clostridium botulinum toxin is a known or reasonably foreseeable hazard, and you package
your covered produce, you must do so in a manner that prevents the formation of C. botulinum
toxin. (21 CFR 112.115)). You should consider your practices and procedures as well as
conditions that could occur during distribution, including temperature fluctuation and exceeding
set holding temperatures. Some measures for covered produce that could help prevent the
formation of C. botulinum toxin when identified as a known or reasonably foreseeable hazard
include:
•

Creating conditions that are less favorable for C. botulinum growth and toxin formation,
such as using open, perforated, or otherwise oxygen-permeable packaging and packing
materials, to allow for gas exchange (i.e., for atmospheric oxygen to replenish the oxygen
used by covered produce respiration);

•

When conditions are more likely to favor C. botulinum growth and toxin formation:
o Using antimicrobial compounds, or other treatments, that are effective to prevent
the growth and toxin formation by C. botulinum;
o Maintaining the temperature of the packaged covered produce below 38°F
(3.3°C); and
o Using time-temperature integrators (trackers) for covered produce to signal when
a cumulative time-temperature combination that presents a risk for C. botulinum
toxin formation is reached.

6. Food-Packing Material
Farms typically place harvested covered produce in containers (i.e., food-packing materials) for
various purposes, such as collecting, conveying, or distributing. Some farms use containers to
transport harvested covered produce from growing areas to packing areas, where the covered
produce is then packed (or repacked) for distribution. For example, food-packing materials
include containers used to collect harvested covered produce (e.g., harvest bins, buckets, and
totes) in growing areas and transport the covered produce to a packing or holding area. In other
instances, harvest containers, such as fiberboard boxes into which the covered produce is placed
when harvested, could be the same containers in which covered produce is distributed (e.g.,
when covered produce is field-packed). Food-packing materials also include “food-packaging
materials,” a term that has long been used (such as in FDA’s human food CGMP regulations in
21 CFR part 117, subpart B (previously 21 CFR Part 110)) to generally refer to a container that
directly contacts the food.
When you use a food-packing material, it must be adequate for its intended use, which includes
being:
89

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•

Cleanable or designed for single use; and
Unlikely to support growth or transfer of bacteria. (21 CFR 112.116(a)).

You should take the following steps to help you determine whether food–packing material is
adequate for its intended use on your farm:
•
•
•

Identify the types of food-packing materials that you use, and determine whether each
type is reusable or for single use;
Determine whether your food-packing materials are unlikely to support the growth or
transfer of bacteria, taking into consideration your handling, maintenance, and storage
practices; and
Determine whether reusable materials can be cleaned, taking into consideration your
handling, maintenance, and storage practices.

Food-packing materials (including food packaging materials) are subject to the provisions of
both 21 CFR 112.116(a) (subpart K) and 21 CFR 112.123(a) (subpart L). To minimize
redundancy and help provide clarity in our draft guidance on food-packing materials, we provide
draft guidance on the aspects of the materials themselves in this chapter. We provide draft
guidance on other regulatory requirements of the Produce Safety Rule related to food-packing
materials, including maintenance, storage, and inspection, in the section of Chapter 7:
Equipment, Tools, Buildings, and Sanitation (Subpart L), titled “Equipment and Tools.”
Pathogens can become established in, grow in, or be transferred from materials that have cracks,
pits, jagged edges, rough areas, score marks, or other damage; these conditions increase the
potential for certain materials to introduce contamination to covered produce (Ref. 128) (Ref.
130) (Ref. 134). Both porous and non-porous materials can facilitate contamination if they are
damaged or their surfaces are not intact (Ref. 10) (Ref. 20) (Ref. 83) (Ref. 92) (Ref. 124).
Identifying Single-Use and Reusable Food-Packing Materials
To ensure that you use a food-packing material that is adequate for its intended use, you should
first identify the types of food-packing materials you use and determine whether they are
reusable or designed for single use. Generally, single-use packing materials are nondurable (e.g.,
easily susceptible to damage), or not easily cleaned (e.g., bags that can be torn, fiberboard that
loses integrity or disintegrates when contacted by water or cleaning solutions). Examples of
single-use food-packing materials include clamshells used for retail packaging of berries, and
foam sleeves used to protect Asian pears from bruising during distribution. You should not reuse
food-packing materials that are designed for single use. Although some single-use food-packing
materials could be sufficiently sturdy for multiple uses, they may not be cleanable after use and,
when reused, could then serve as a source of contamination or support bacterial growth or
transfer (Ref. 10). Generally, some materials, such as fiberboard or foam, may not be suitable to
reuse as packing materials because they are likely to support the growth of bacteria or cannot be
adequately cleaned because the structure of the material prevents removal of organic material
and bacteria or traps moisture, or the materials could degrade during cleaning (Ref. 10) (Ref. 53)
(Ref. 136).

90

Contains Nonbinding Recommendations
Draft-Not for Implementation
Evaluating Your Practices and Food-Packing Materials
You should periodically evaluate your practices, including handling, maintenance, and storage of
your food-packing materials, to determine whether, under the conditions, your food-packing
materials are adequate for its intended use, including being unlikely to support the growth or
transfer of bacteria and whether your reusable packing materials are cleanable. Your practices or
use of food packing materials could change over time, and you should account for these changes
as appropriate; periodic evaluations can assist you with ensuring that you consider any changes.
You should consider several factors that influence whether food-packing materials are adequate
for their intended use, including:
•

•
•
•
•
•
•
•
•
•

The type of the material (e.g., plastic, metal, wood, foam, cardboard);
o The nature of the material (e.g., smooth, course, absorbent, porous, non-porous,
or); and
o The durability of the material (e.g., fragile, malleable, firm, sturdy);
The construction (e.g., solid, stapled, hollow components);
The food-packing material handling practices (i.e., how carefully they are handled during
receiving, storage, and preparation for use);
The existing condition of the material (e.g., intact, damage, surface abrasions);
The characteristics of the covered produce for which the packing material is used (e.g.,
heavy, light, hard shell, soft skin, moist, dry);
How the covered produce is placed into the food-packing material (e.g., by hand or by
machine and how that can impact the potential for damage to the food-packing material);
Use of single-use, clean liners in otherwise reusable food-packing materials;
The impact of sanitation procedures (i.e., the cleaning and, when necessary and
appropriate, sanitizing process), treatments or chemicals used, and devices used on the
food-packing material;
The storage conditions (e.g., outdoor vs. indoor); and
The maintenance practices (e.g., approaches to repair or replace worn or damaged
components).

The following are examples using the principles and recommendations discussed in this section
to illustrate approaches to evaluating food-packing materials and their use based on the
requirements of 21 CFR 112.116 and 21 CFR 112.123. To minimize redundancy, concepts
related to maintenance, storage, inspection, cleaning, and when necessary and appropriate,
sanitizing, are discussed in examples found in the section of Chapter 7: Equipment, Tools,
Buildings, and Sanitation (Subpart L), titled “Equipment and Tools”. These examples are
intended to illustrate concepts, and are not intended to be universally applicable. For illustrative
purposes, we identify specific covered produce in these examples. Even if you use similar
materials or practices for the specific covered produce mentioned here, you should perform your
own evaluation based on your farm’s specific practices and conditions.
a.

Example 6b: Plastic bags

A farm uses plastic bags for field packing celery in the growing area for distribution to retail
stores. The farm evaluates the plastic bags and their use, and concludes the following:
91

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•
•
•
•
•

The bag material is primarily polyethylene, which is:
o smooth and non-absorbent; and
o fragile (e.g., can be torn) and malleable;
The bag construction does not include voids or seams that could trap organic material or
bacteria;
The bags are received from the manufacturer in containers that protect them from
damage, and the farm’s procedures confirm the bags are in sound condition upon receipt;
The bag handling practices typically do not result in damage prior to use;
During field packing, each bag’s condition is intact and the bags are not reused;
The celery has a firm surface that is usually dry; and
The bag is sufficiently durable to withstand the celery being placed by hand into the bag.

The farm determines that the bags are suitable to distribute the celery and are a single-use food–
packing material, and continues to periodically evaluate the use and handling of the bags.
b. Example 6c: Wax–impregnated, corrugated fiberboard boxes
A farm places honeydew into wax-impregnated, corrugated fiberboard boxes for distribution.
The farm evaluates the waxed, corrugated fiberboard boxes and their use, and concludes the
following:
•
•
•
•
•
•
•

The box material is wax-impregnated, corrugated fiberboard, which is:
o smooth and porous, with the wax surfaces having some moisture resistance; and
o fragile and malleable (e.g., can be bent, dented, or torn);
The box construction includes open seams that could trap organic material or bacteria;
The boxes are received from the manufacturer on shrink-wrapped pallets that protect
them from damage, and the farm’s procedures confirm the boxes are in sound condition
upon receipt;
The box handling practices typically do not result in damage prior to use;
During packing, each box’s condition is intact, and the boxes are not reused;
The honeydew has a firm surface that is usually dry; and
The boxes are sufficiently durable to withstand the honeydew being placed by hand into
the box.

The farm determines that the boxes are suitable to distribute the honeydew and are a single-use
food–packing material, and continues to periodically evaluate the use and handling of the boxes.

92

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 7:
Equipment, Tools, Buildings, and Sanitation (Subpart L)
Maintaining sanitary conditions where covered activities occur is critical to prevent
contamination of covered produce from the surrounding environment (including buildings,
sanitation systems, equipment, and tools) (Ref. 16). A lack of sanitation can promote harborage
of pathogens in the environment, which can increase the likelihood of contamination of covered
produce (Ref. 16) (Ref. 52) (Ref. 53) (Ref. 79) (Ref. 108).
This chapter provides draft guidance on the requirements of subpart L–Equipment, Tools,
Buildings, and Sanitation. The discussion is divided into sections on: equipment and tools;
buildings; other sanitation measures; and records. Where applicable, we recommend evaluating
your relevant practices, procedures, and processes periodically to ensure that you consider the
scope of your relevant activities or operations and any changes that occurred and how they are
affected by and relate to your equipment, tools, buildings, and sanitation and the requirements of
the Produce Safety Rule. During such evaluations, you should consider not only typical
practices, but also those that occur infrequently or due to unusual circumstances, to account for
the breadth of procedures, processes, and practices associated with a given activity.

1. Equipment and Tools
Farms use many types of equipment and tools. Several factors affect the ability of equipment or
tools to be adequately cleaned or properly maintained, including: the type of materials; the
design, construction, or workmanship; wear or damage; and cleaning practices. This section
provides more detailed draft guidance related to these topics.
In this chapter, we provide draft guidance related to equipment and tools that are intended to, or
likely to, contact covered produce and those instruments or controls used to measure, regulate, or
record conditions to control or prevent the growth of microorganisms of public health
significance, as described in 21 CFR 112.121. You should take the following steps based on the
requirements of the Produce Safety Rule related to equipment and tools:
•
•
•
•
•
•
•

Identify equipment and tools on your farm that are intended to, or likely to, contact
covered produce, including instruments and controls used to measure, regulate, or record
conditions;
Evaluate the design, construction, workmanship, installation, and maintenance of these
equipment and tools;
Evaluate your storage and maintenance practices and storage locations for these
equipment and tools;
Establish procedures and schedules for cleaning, and, when necessary and appropriate,
sanitizing, food contact surfaces of these equipment and tools;
Establish procedures and schedules to conduct inspections of these equipment and tools;
Evaluate your use of transport equipment with covered produce; and
Evaluate the accuracy, precision, maintenance and numbers of instruments and controls
used to measure, regulate, or record conditions to control or prevent the growth of
microorganisms of public health significance.
93

Contains Nonbinding Recommendations
Draft-Not for Implementation
Identifying Equipment and Tools Intended or Likely to Contact Covered Produce
You should visually assess your covered activities and your growing, harvesting, packing, and
holding areas to identify the equipment and tools that are intended to, or likely to, contact your
covered produce. The way you handle covered produce while using equipment or tools, or vice
versa, can affect whether contact is likely, as illustrated in the following examples:
Example 7a: If you pack covered produce on a stainless steel table permanently attached
to a wall, you could find that the covered produce frequently contacts the surface of the
wall. In this case, you should consider both the table and the wall to be pieces of
equipment that are intended or likely to contact covered produce.
Example 7b: If separate guards or shields placed near other equipment occasionally
contact covered produce or produce rinse water spray routinely rebounds from the guard
or shield to a food contact surface, you should identify these guards and shields as pieces
of equipment that contact or are likely to contact covered produce.
Design, Construction, and Workmanship
For equipment and tools subject to this subpart, you must use equipment and tools that are of
adequate design, construction, and workmanship to enable them to be adequately cleaned and
properly maintained. (21 CFR 112.123(a)). The considerations are the same whether you design
your own equipment and tools, purchase them prefabricated, or repurpose them.
Food-packing materials (including food packaging materials) are subject to the provisions of 21
CFR 112.116(a) (Subpart K) and 21 CFR 112.123(a). We provide draft guidance on the aspects
of the materials themselves in the section of Chapter 6: Growing, Harvesting, Packing, and
Holding Activities (Subpart K) titled “Food-Packing Material.” We provide draft guidance on
other regulatory requirements of the Produce Safety Rule related to food-packing materials in
this section on “Equipment and Tools.”
Evaluating Materials
You should evaluate the materials used to make your equipment and tools. You should consider
whether the materials from which they are constructed will affect whether they can be adequately
cleaned or properly maintained under the conditions of their use and throughout the period of
their use, considering: stress and strain during use; environmental conditions during use or
storage (e.g., wet, humid, dry); and the process of, and treatments used during, cleaning and,
when applicable, sanitizing. Equipment and tools made of non-porous materials, such as
stainless steel and food-grade plastic (e.g., PVC, nylon), could allow for a wider range of
effective cleaning methods; whereas porous material, such as fabric, cardboard, foam, and
carpet, can trap moisture, making it difficult to remove organic material and bacteria.
We recommend that you use equipment and tools made from non-porous materials to the extent
practical. However, we understand that covered farms sometimes use porous materials such as
wood, fabric, or foam when conducting covered activities. If you choose to use equipment and
tools made of these materials, the equipment and tools must be of adequate design, construction,
94

Contains Nonbinding Recommendations
Draft-Not for Implementation
and workmanship to enable them to be adequately cleaned and properly maintained. (See 21
CFR 112.123(a). We provide further draft guidance on cleaning and sanitizing in of the section
of this chapter titled “Cleaning and Sanitizing Equipment and Tools.”
Evaluating Design, Construction, Workmanship, and Seams
You should evaluate the design, construction and workmanship of your equipment and tools,
including whether the equipment and tools:
•

•

Allow for access to all the components for cleaning, maintenance, and, when appropriate,
inspection; and
Limit the potential for moisture or organic material to accumulate on or within the
components of the equipment or tool, and subsequently to drip or drain onto covered
produce or spread contamination.

For example, equipment and tools should not have openings to hollow areas that are not
otherwise accessible for cleaning and maintenance.
You could choose to seek more information from sources such as equipment manufacturers,
academia, extension services, industry associations, and government agencies to assist you with
this evaluation.
Seams on food contact surfaces of equipment and tools that you use must be either smoothly
bonded, or maintained to minimize accumulation of dirt, filth, food particles, and organic
material and thus minimize the opportunity for harborage or growth of microorganisms. (21
CFR 112.123(c)). The materials and surfaces of equipment and tools should not have pits,
corrosion, cracks, crevices, partially open seams, poorly bonded welds, rough areas or other
damage. Such defects can allow for the accumulation of moisture and organic material and can
harbor or transfer bacteria (Ref. 128) (Ref. 130) (Ref. 134).
You should repair or replace any equipment or food contact surface that is damaged in a way that
it can no longer be adequately cleaned or properly maintained. (See 21 CFR 112.123(a)).
Installation and Maintenance
Equipment and tools must be installed and maintained as to facilitate cleaning of the equipment
and of all adjacent spaces. (21 CFR 112.123(b)(1)). You should evaluate the installation and
maintenance of your equipment and tools, and you should visually assess your farm’s activities
to confirm your practices. You should consider the potential for installed equipment or tools to
accumulate moisture, organic material, or other potential sources of contamination that could
contact, drip or drain onto covered produce or food contact surfaces. You should also consider
the potential for surrounding surfaces to transfer moisture, organic material, or other potential
sources of contamination onto covered produce or food contact surfaces of your equipment and
tools.
You should install equipment so that maintenance and cleaning personnel can easily access all
food contact surfaces, protective coverings or barriers, equipment framework, any movable parts,
95

Contains Nonbinding Recommendations
Draft-Not for Implementation
and other relevant parts. For example, parallel conveyor belt systems should be installed with
enough space between the systems to allow personnel to easily access the lines to perform
maintenance, cleaning, and production activities. This should include access to the belts, the
framework supporting the belts, any enclosed housings for electrical components, and the points
at which the framework is secured. Maintenance and cleaning personnel should also have access
to adjacent spaces, such as the floors, walls, ceilings, and other equipment and tools in the
immediate vicinity. For example, if a conveyor belt system becomes loose and drags on the floor
as it rotates, personnel should have access to repair or replace the conveyor belt system. In this
example, you or your personnel should also determine whether any damage occurred to the
equipment or the floor, any necessary steps to clean and, when necessary and appropriate,
sanitize the equipment and floor, and whether any other measures are necessary.
The condition of your equipment and tools, including their surfaces, is likely to degrade over
time due to age, wear, or damage. Such degradation could result in cracks, crevices, pits, jagged
edges, rough surfaces, score marks, and other conditions or damage that can allow the potential
for contamination. You should evaluate your inspection and maintenance practices to ensure that
you periodically assess for, and correct, any defects as soon as they are identified. You should
repair or replace any equipment or tool that is damaged in a way that it can no longer be
adequately cleaned or properly maintained. (See 21 CFR 112.123(a)).
In some instances, maintenance practices could include repair. There are several options to
address the condition of equipment and tools, including refinishing, resurfacing, or removing and
replacing components to reestablish cleanable surfaces. For example, re-welding or grinding
rough seams can smooth the surface and re-establish cleanability. In another example, a scored
table top could be resurfaced or replaced.
Storage
Equipment and tools (including food-packing materials) must be stored and maintained to protect
covered produce from being contaminated with known or reasonably foreseeable hazards and to
prevent the equipment and tools from attracting or harboring pests. (21 CFR 112.123(b)(2)).
You should evaluate your storage locations periodically to determine the potential for
contamination of equipment and tools stored in them, and note their proximity to potential
sources of contamination. For example, storage areas or buildings located near tree lines could
increase the potential of rodent infestation (Ref. 95) (Ref. 135), which could warrant different
procedures to protect covered produce from being contaminated with known or reasonably
foreseeable hazards. Storage areas, including outdoor storage areas and storage areas in partiallyenclosed buildings, can attract pests and serve as a harborage for pests (Ref. 95) (Ref. 135),
especially if equipment and tools are stored for extended periods. See the section of this chapter
titled “Pest Control” for further draft guidance on the control of pests.
You should establish procedures to ensure that equipment and tools (including food-packing
materials) are stored in a manner based on the requirements of 21 CFR 112.123(b)(2). For
example, you could find that sorting equipment used for daily field packing during the season
can be protected overnight (after cleaning, and sanitizing as necessary and appropriate, at the end
of the production cycle) by storing it in a partially-enclosed building with a clean covering (e.g.,
a tarp) over the sorting equipment to protect it from pests such as birds, accumulating debris, and
96

Contains Nonbinding Recommendations
Draft-Not for Implementation
weather or other conditions. However, you could determine the sorting equipment will not be
protected from contamination from pests, such as rodents, if it is stored long-term in a partiallyenclosed building. You could determine, for example, that these pieces of equipment should be
stored long-term in a fully enclosed building, where rodents can be more easily controlled.
Equipment and tools should be clean and dry before storage to minimize the attraction of pests
and protect covered produce from being contaminated. Additionally, you should close or cover
any openings into the equipment or tools to reduce the potential for pests to enter (e.g., placing a
tarp over food contact surfaces, capping openings of pipes to prevent birds or rodents from
nesting) (Ref. 80). You could determine that a deep cleaning, and sanitizing as necessary and
appropriate, procedure (i.e., beyond routine procedures) is appropriate when removing certain
equipment and tools from storage. See more draft guidance on cleaning and sanitizing in the
section of this chapter titled “Cleaning and Sanitizing Equipment and Tools.
Equipment and tools, including food-packing materials, must be protected, including during
outdoor storage, from sources of contamination (See 21 CFR 112.123(b)(2), such as dust, dirt,
and debris, or cleaned prior to use (See 21 CFR 112.123(d)). You should periodically inspect
your storage of equipment and tools, including food-packing materials, that are intended to, or
likely to, contact covered produce to ensure they are protected from contamination and do not
attract or harbor pests. You should establish procedures for inspection of your storage areas,
including the frequency of these inspections, the personnel involved, and conditions that should
be reported to you, a supervisor, or responsible party.
Inspection
You must inspect all food contact surfaces of equipment and tools (including food-packing
materials) that are used in covered activities as frequently as reasonably necessary to protect
against contamination of your covered produce. (See 21 CFR 112.123(d)(1)). You should also
consider inspecting non-food contact surfaces of equipment and tools. You could perform these
inspections as independent activities or in conjunction with other activities, such as cleaning,
sanitizing, or scheduled maintenance. Periodic inspection of your equipment and tools can help
you to identify signs of potential contamination (e.g., visible soil, food residue, grease, or other
material) and determine whether maintenance, replacement, or cleaning, or sanitizing is
necessary.
You should establish and communicate procedures for inspecting equipment and tools (including
food-packing materials), the frequency of these inspections, the personnel involved, and
conditions that should be reported to you, a supervisor, or responsible party to determine
appropriate steps to protect covered produce. Personnel, to whom you assign the responsibility
for the inspection of food contact surfaces of equipment and tools (including transport equipment
and instruments and controls, discussed in other sections of this chapter), or who are engaged in
the supervision thereof, should understand your procedures for performing inspections. You
should direct your supervisors or other responsible parties to ensure that your personnel are
consistently inspecting equipment and tools in accordance with your procedures and making
corrections as needed. You should also establish procedures to communicate your expected
practices when personnel observe unclean, damaged, or worn equipment and tools, including
food-packing materials. For example, personnel you assign to inspect food-packing materials
97

Contains Nonbinding Recommendations
Draft-Not for Implementation
and those who supervise or are otherwise responsible for your operations involving food-packing
materials should recognize food-packing materials that can no longer be cleaned. In this
example, supervisors and other responsible parties should ensure that only food-packing
materials adequate for their intended use are being used. Your evaluation of your equipment,
tools and practices can guide you in developing your inspection procedures.
You should perform inspections after each cleaning activity and before using equipment and
tools to ensure that the cleaning activity was effective in removing residue from previous
activities and that the equipment and tools remain clean during periods of storage. Inspections
should include visually assessing for remaining residues, such as visible soil, food residue,
grease, or other material. In some instances, performing inspections on dry equipment and tools
can make it easier for personnel to see remaining residues such as visible soil than if the
inspection is performed when the surface is wet. The visual assessment should include the
entirety of the equipment or tool, including areas that are difficult to access or clean, such as the
underside of equipment (which could require the use of lights or other visual aids).
The frequency at which you inspect the condition of your equipment and tools (e.g., for pitting,
cracking, damage, partially open seams, excessive wear that provides harborage areas for
moisture, organic material, and pathogens) is dependent upon the nature of the equipment or tool
and its use. When determining your inspection frequency, you should consider factors including:
•
•
•
•
•
•
•
•

The materials used (e.g., the type, nature, and durability of metal, plastic, wood, or fabric
materials);
The construction technique (e.g., the durability of welded or bolted construction);
The conditions of use, including impact, abrasion, characteristics of covered produced,
such as weight, texture, hardness;
The cleaning process and treatments used (e.g., reactivity with the materials, abrasion
from scrubbing or scraping);
The storage conditions of the equipment or tool (e.g., potential damage from outdoor or
indoor storage);
The climate (e.g., high humidity could result in more rapid deterioration);
The age of the equipment and tools (i.e., wear and damage associated with age); and
How often the equipment and tools are used (i.e., wear and damage associated with use).

Based on your evaluation of these factors, you could, for example, choose to establish different
inspection frequencies for different types of equipment and tools. For example, you could
determine that you need to implement a more frequent inspection schedule, such as daily or
weekly, for equipment or tools that are frequently used or are likely to become worn or damaged
relatively quickly (e.g., those with materials such as fabrics or thin blades, or those that are used
under intense conditions). Or, for example, you could find that for equipment and tools that are
of highly durable construction or receive infrequent or light use, you can inspect them less
frequently (e.g., at the beginning of each growing season and monthly thereafter).
You should inspect single-use food-packing materials upon receipt or immediately before use to
protect against contamination of your covered produce. Generally, if single-use or reusable food
packing materials are stored in a way, or location, where there is a potential for contamination,
98

Contains Nonbinding Recommendations
Draft-Not for Implementation
they should be inspected before use. For example, your procedures could specify that your
personnel will inspect reusable harvest containers prior to use, identify and set aside unclean or
damaged containers, and notify a supervisor or responsible party of any unclean or damaged
containers.
The outcomes of your inspections should guide your decisions about continued use of your
equipment and tools. You could determine that replacing certain equipment or tools or adjusting
equipment or tool placement, storage practices, or maintenance, cleaning, or sanitizing practices
is necessary to minimize the potential for contamination of covered produce and food contact
surfaces. For inspections performed after each cleaning activity and before using equipment and
tools, you could find that additional steps are necessary prior to using the equipment or tools.
Examples
The following examples use the principles and recommendations discussed so far in this chapter
to illustrate how a farm could evaluate their equipment and tools, conditions and practices based
on the requirements. The approaches described may not be appropriate for every scenario based
on a farm’s circumstances. For illustrative purposes, we identified specific covered produce for
these examples. Even if you use similar practices for the specific covered produce mentioned
here, you should perform your own evaluation based on your farm’s specific conditions and
practices; there could be circumstances where your practices and conditions would lead you to a
different determination than the outcomes in the examples. In these examples the farm visually
assesses and evaluates their procedures to determine whether the equipment and tools covered by
subpart L that they use are of adequate design, construction, and workmanship to enable them to
be adequately cleaned and properly maintained based on the requirements of 21 CFR 112.123(a).
The farm also determines whether seams on food contact surfaces of these equipment and tools
are either smoothly bonded or maintained to minimize accumulation of dirt, filth, food particles,
and organic material and thus minimize the opportunity for harborage or growth of
microorganisms based on the requirements of 21 CFR 112.123(c). Further, in these examples,
the farm determines whether the equipment and tools are stored and maintained to protect
covered produce from being contaminated and to prevent them from attracting and harboring
pests based on the requirements of 21 CFR 112.123(b)(2). Finally, in these examples, the farm
determines whether the food contact surfaces of the equipment and tools are inspected and
maintained as frequently as reasonably necessary to protect against contamination of covered
produce based on the requirements of 21 CFR 112.123(d)(1). We discuss approaches to
cleaning, and, when necessary and appropriate, sanitizing equipment and tools in the section of
this chapter titled “Cleaning and Sanitizing Equipment and Tools.” Your practices or procedures
or use of your equipment or tools could change over time, and you should account for these
changes as appropriate; periodic evaluations can assist you with ensuring that you consider any
changes that occur.
Examples of farm evaluations that do not lead to a change in equipment or tools, practices or
procedures:
Example 7c. Harvest trailer with a wooden floor for hauling watermelons.

99

Contains Nonbinding Recommendations
Draft-Not for Implementation
A farm uses a harvest trailer with a wooden floor to carry watermelons from the field to a
packing area. The farm observes that the harvest trailer typically remains dry during use, and
that the watermelons remain intact, with very few observations of damage to the watermelons
that could result in watermelon residue or liquid from the watermelons leaking onto the
trailer. The farm’s procedures specify that the harvest trailer is to be kept clean and dry,
maintained (e.g., free from splinters and cracks), and stored in a way that protects it from
moisture, damage, and contamination, such as in a covered storage shed or garage to
minimize the potential for contamination. The farm directs their personnel using the trailer
to inspect it for cleanliness and damage both prior to use and after each load, to maintain the
trailer, and to clean the trailer by removing organic material, debris, and other material as
necessary. Personnel ensure that they do not place moist or damaged watermelons into the
trailer. The farm determines that their procedures are consistently followed by personnel,
continues to use the harvest trailer, and periodically evaluates their practices and procedures.
Example 7d. Storage and inspection of plastic bags.
A farm uses single-use plastic bags for packing celery in the growing area. The farm
evaluates their storage, inspection and handling practices for this material from the time of its
receipt until it leaves the farm. The farm receives the plastic bags in containers on a pallet.
The farm stores and maintains the bags as received from the supplier in a fully enclosed
building in a clean, dry environment until ready for use. Any plastic bags that are not used at
the completion of field packing are covered, transported and stored in a fully enclosed
building on pallets. When the farm is ready to use the material, the pallets are transported to
the growing area, and the bags are inspected when they are loaded onto the packing
equipment. If they find any signs of potential contamination they do not use the bags and
report the conditions to a supervisor or other responsible party. Further, a supervisor or other
responsible party inspects the storage area weekly. The farm continues to periodically
evaluate their practices and procedures.
Example 7e. Storage and inspection of wax-impregnated corrugated fiberboard boxes
stored in a partially-enclosed building.
A farm packs honeydew inside a partially-enclosed building and uses single-use, waxed,
corrugated fiberboard boxes. The unformed fiberboard boxes are received and stored in
shrink-wrap. The farm’s procedures specify that the boxes are to be stored indoors in a
clean, dry environment. Additionally, they specify that, when in the packing area, the
unformed and formed boxes are kept on a pallet in a clean, dry area, away from personnel
and equipment traffic, that each pallet is unwrapped on an as-needed basis, and that any
unused boxes are to be moved to the indoor storage area daily when packing activities
conclude. They also specify that personnel are to inspect the boxes for any signs of potential
contamination, damage, or poor condition (e.g., moisture) prior to using them; and that if
they find such evidence, they are not to use the boxes and are to report the conditions to a
supervisor or other responsible party. Further, they specify that a supervisor or other
responsible party is to inspect the location where the boxes are kept in the packing area
periodically during the day to ensure that personnel follow these practices, and that a
supervisor or other responsible party is to inspect the packaging storage area weekly. The
farm continues to periodically evaluate their practices and procedures.
100

Contains Nonbinding Recommendations
Draft-Not for Implementation
Example 7f. Storage and inspection of harvest containers stored outdoors.
A farm uses reusable plastic harvest containers to transport and hold pears. The containers
are stored outdoors. The farm’s procedures specify that the containers are to be cleaned prior
to use. They specify that the container storage area is to be inspected by a supervisor or other
responsible party twice a week. Also, they specify that personnel are to inspect the
containers for cleanliness, damage, and poor condition immediately prior to use to protect the
pears that contact them from contamination. Further, they specify that when personnel
observe damage to containers to the extent that they can no longer be properly cleaned, the
containers should be discarded. The farm continues to periodically evaluate their practices
and procedures.
Example 7g. Storage and inspection of harvest containers stored outdoors with temporary
storage in the growing area.
A farm uses reusable wood harvest containers to transport cabbage for packing and holding.
The containers are removed from an outdoor long-term storage area and temporarily stored
outdoors in a growing area for several days prior to harvest. The farm’s procedures specify
that the long-term container storage area and the storage areas in each growing area are to be
inspected by a supervisor or other responsible party twice a week. The farm’s procedures
specify that personnel are to clean and dry the containers as they are removed from long-term
storage for use. They also specify that personnel are to inspect the containers immediately
prior to use for cleanliness, damage, and poor condition. Further, they specify that unclean
containers are to be set aside for re-cleaning or replacement, and that damaged containers
that can no longer be properly cleaned should be repaired or discarded. The farm continues
to periodically evaluate their practices and procedures.
Examples of farm evaluations leading to a change in equipment or tools, practices or
procedures:
Example 7h. Harvest trailer with wooden floor for hauling tomatoes.
A farm uses a harvest trailer with a wooden floor to move tomatoes from the field to a
packing area. The farm observes that the tomatoes are frequently damaged during loading
and transport such that tomato residue or liquid leaks onto the wooden floor of the trailer.
The farm determines that the wooden floor with tomato residue is difficult to clean and is not
a suitable food contact surface under the circumstances. The farm changes their procedures
to include placing a clean, durable, non-porous, food grade, single-use liner in the harvest
trailer to minimize the potential for contamination of the tomatoes from the wooden floor of
the trailer. The farm directs their personnel using the trailer to inspect the trailer and liners
for cleanliness and damage prior to use, to maintain the trailer and to change the single-use
liners between each load. The farm continues to periodically evaluate their practices and
procedures.
Example 7i. Harvest trailer with carpeting material on the floor for hauling cantaloupe.

101

Contains Nonbinding Recommendations
Draft-Not for Implementation
A farm uses carpeting material on a harvest trailer used to convey cantaloupe. The farm
observes that the carpeting material reduces product bruising but it also absorbs moisture and
organic material that is difficult to remove. The farm determines that they cannot perform
proper cleaning to maintain the carpeting material in a manner that protects against
contamination. The farm removes the carpeting and uses materials that are of a design,
construction, and workmanship that farm personnel can adequately clean and maintain.
Depending on their circumstances, this could include using reusable materials, such as
plastic, or single-use materials, such as foam or plastic, or a different vehicle. The farm
continues to periodically evaluate their practices and procedures.
Example 7j. Table with a wooden food contact surface used to sort radishes.
A farm sorts radishes using a sorting table with a wooden surface on a metal support system.
Farm personnel wash the radishes before sorting. While conducting its evaluation, the farm
observes that the wooden surface of the table accumulates soil, residue, and moisture from
the radishes during sorting, and the farmer determines that personnel cannot properly clean
the wooden surface of the table manner that protects against contamination. The farm
replaces the wooden top of the sorting table with a food grade material top that is of adequate
design, construction, and workmanship that farm personnel can adequately clean and
maintain. Depending on the circumstances, this could include stainless steel, plastic or other
materials. The farm continues to periodically evaluate their practices and procedures.
Example 7k. Foam pads on equipment used to convey apples.
A farm uses foam pads on equipment used to convey apples. The foam pads contact the
apples. The farm observes that the foam pads are not designed for frequent removal from the
equipment which allows for the accumulation of dirt and other organic material, and the
porous nature of the material allows for the accumulation of organic material on and
underneath the pads. The farm determines that they cannot adequately clean the foam pads
in a manner that protects against contamination given their equipment, conditions and
practices. The farm evaluates several options, including:
• Replacing the foam pads as frequently as reasonably necessary to protect against
contamination;
• Removing the foam pads;
• Adding a removable liner, such as a plastic liner, over the foam with adequate design,
construction, and workmanship that personnel can adequately clean and maintain;
• Replacing the foam pads with a food grade material with adequate design, construction,
and workmanship that enables personnel to adequately clean and properly maintain, such as a
different type of foam, plastic or other material; or
• Replacing the equipment with that which has a design, construction, and workmanship
that is more compatible with the farm’s operations.
The farm could also choose to take a short-term approach, such as removing or replacing the
pads, and develop a long-term plan to replace the equipment with that which has a design,
construction, and workmanship that is more compatible with the farm’s operations. The farm
continues to periodically evaluate their practices and procedures.
102

Contains Nonbinding Recommendations
Draft-Not for Implementation
Example 7l. Inspection of harvest containers stored outdoors with evidence of
contamination.
A farm uses reusable plastic harvest containers to transport nectarines to a holding area. The
containers are stored outdoors. The farm’s procedures specify that personnel are to inspect
the containers immediately prior to use for cleanliness, damage, and poor condition
immediately prior to use to protect the nectarines that contacts them from contamination.
The farm determines that the storage area is to be inspected by a supervisor or other
responsible party twice a week. A supervisor inspecting the storage area observes rodent
excreta in some of the storage containers. Based on the outcome of the supervisor’s
inspection, the plastic harvest containers located in the area in which evidence of rodent
infestation was observed are designated for cleaning and sanitizing or replacement, as
appropriate. The farm also determines whether other measures are necessary, such as
increasing the frequency of inspection and changes to pest control measures.
Example 7m. Foam pads in plastic bin containers to cushion cherries.
During harvesting, a farm uses foam pads to cushion cherries in plastic containers, and the
foam pads contact the cherries. The farm observes that the pads become moist during
refrigerated cooling, and the pads remain in place as the packing containers are transported to
the packing area. The farm determines they have limited information on the effectiveness of
cleaning porous foam materials, and gathers information from the manufacturer of the foam
pads and from technical assistance resources to assist in their determination of whether the
pads are appropriate for use as a reusable material. If the farm determines the foam pads can
be cleaned and that, under their conditions of use, they are unlikely to support the growth of
bacteria, then they could reuse the pads with appropriate cleaning. If the farm determines
that the foam pads are not cleanable, they must not reuse them. (See 21 CFR 112.123). If
the farm determines that single-use of the pads is unlikely to support growth or transfer of
bacteria, then they could choose to designate them for single-use.
Cleaning and Sanitizing Equipment and Tools
Cleaning and sanitizing are different steps that are important to the safety of your covered
produce. Unsanitary equipment and tools can serve as a source of contamination for produce
(Ref. 8) (Ref. 10) (Ref. 48) (Ref.108). You must inspect, maintain, clean, and, when necessary
and appropriate, sanitize all food contact surfaces of equipment and tools used in covered
activities as frequently as reasonably necessary to protect against contamination of covered
produce. (21 CFR 112.123(d)(1)). You also must maintain and clean all non-food contact
surfaces of equipment and tools subject to subpart L used during harvesting, packing, and
holding as frequently as reasonably necessary to protect against contamination of covered
produce. (21 CFR 112.123(d)(2). You should evaluate your equipment and tools by taking the
following steps:
•

Identify food contact surfaces and non-food-contact surfaces of equipment and tools; and

103

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

Determine cleaning practices, and, as necessary and appropriate, sanitizing practices for
each type of equipment and tool, and the frequency at which you will perform these
practices.
Identifying Food Contact Surfaces and Non-Food Contact
Surfaces of Equipment and Tools

In the section of this chapter titled “Equipment and Tools,” we recommend that you identify all
equipment and tools on your farm that are intended or likely to contact covered produce. For
these equipment and tools, you should also identify their food contact surfaces and non-food
contact surfaces.
“Food contact surfaces” means “those surfaces that contact human food and those surfaces from
which drainage, or other transfer, onto the food or onto surfaces that contact the food ordinarily
occurs during the normal course of operations. ‘Food contact surfaces’ includes food contact
surfaces of equipment and tools used during harvest, packing, and holding.” (21 CFR 112.3).
“Food contact surfaces” also includes food contact surfaces of equipment and tools used in
growing covered produce (See 21 CFR 112.123(d)(1)).
You should carefully evaluate your practices during covered activities to identify the food
contact surfaces of your equipment and tools. You should visually assess your covered activities
to identify food contact surfaces during production activities. Some food contact surfaces could
not be easily identified when production activities are not occurring. In particular, you should
look for drainage, or other mechanisms of transfer (e.g., water splash) that occur. In some cases,
you could have the flexibility to adjust your practices to avoid surfaces being considered food
contact surfaces (see Example 7o). The following examples illustrate how a farm could evaluate
their equipment and tools, practices and conditions to identify food contact surfaces and nonfood contact surfaces. Even if you use similar equipment, tools or practices, you should perform
your own evaluation based on your farm’s specific practices and conditions.
Example 7n: A farm observes that the fine mist of water from the nozzles of a spray bar over
a conveyor belt containing covered produce contacts the bar itself, resulting in water dripping
from the bar onto the covered produce; in this example, the farm should consider the spray
bar a food contact surface.
Example 7o: A farm observes parsley protruding through openings in a plastic container that
touches the table where the containers were placed, so the farm should consider the table a
food contact surface. The farm could start placing a removable plastic surface between the
containers and the table so that the table is not the food contact surface.
Example 7p: A farm observes a conveyor belt system used to move turnips and determines
that the conveyor belt and some support bars underneath that contact the conveyor belt are
food contact surfaces. The farm carefully evaluates the conveyor belt system to determine if
other components are food contact surfaces, such as through drainage or other mechanisms of
transfer. The farm identifies other components of the system, including the legs of the
support structure for the conveyor belt system and the housings for electrical components, are
not food contact surfaces.
104

Contains Nonbinding Recommendations
Draft-Not for Implementation
Cleaning and Sanitizing Procedures
Once you have identified equipment and tools subject to subpart L, and the associated food
contact surfaces, you should evaluate and determine appropriate cleaning practices and
frequencies for food contact surfaces and non-food contact surfaces. You must inspect, maintain
and clean and, when necessary and appropriate, sanitize all food contact surfaces of equipment
and tools used in covered activities, and maintain and clean all non-food contact surfaces of
equipment and tools used during harvesting, packing, and holding, as frequently as reasonably
necessary to protect against contamination of covered produce. (21 CFR 112.123(d)(1) and (2)).
Cleaning and sanitizing activities should be performed both on a scheduled, periodic basis and in
response to identified problems or potential contamination.
Periodically performing cleaning and sanitizing procedures, including deep cleaning and
sanitizing procedures, can increase effective soil removal, biofilm prevention and removal, and
pathogen inactivation (Ref. 18) (Ref. 38) (Ref. 83) (Ref. 134). You should consider performing
deep cleaning and sanitizing, as necessary and appropriate, procedures (i.e., beyond routine
procedures) on a scheduled, periodic basis. These procedures can involve additional or different
activities, such as disassembling equipment for more targeted cleaning when your routine
procedures involve cleaning the assembled equipment (Ref. 66) (Ref. 134). It can also involve
using a different sanitizing compound than is typically used during routine procedures, in order
to impact a broader range of potential microorganisms (Ref. 15) (Ref. 18) (Ref. 83) (Ref. 93)
(Ref. 134).
Your cleaning methods should remove potential sources of contamination, including visible soil,
food residue, grease, and other material. Cleaning methods can be broadly divided into wet
cleaning and dry cleaning. Generally, wet cleaning is the most effective method to remove
organic material (Ref. 15) (Ref. 82), and involves the use of water and cleaning solutions. There
are a variety of different cleaning agents you can choose based on your specific needs. You
should select a cleaning agent based on, for example, the structure of the items to be cleaned, and
the nature of the potential contamination. Some options could include general purpose cleaners,
alkaline and chlorinated detergents, or acid and enzyme detergents (Ref. 83) (Ref. 97). You
could choose to work with technical assistance resources, such as cleaning and sanitation
suppliers, academia, extension services, and industry associations to determine the most
appropriate cleaning and sanitizing treatments for your operations.
In some circumstances, dry cleaning could be preferable to wet cleaning, such as when covered
produce with dry surfaces are handled in a dry, low moisture environment. In certain situations,
the introduction of water into the otherwise low moisture environment can increase the potential
for growth of some pathogens that could be present; such pathogens would be unlikely to grow
without the addition of water (Ref. 12) (Ref. 11) (Ref. 43). Dry cleaning typically involves
mechanical action for the removal of organic material and other residues.
You should evaluate your production environment, covered produce, and equipment and tools
you use to determine when you should sanitize and identify sanitizing methods appropriate for
food contact surfaces of your equipment and tools. “Sanitize means to adequately treat cleaned
surfaces by a process that is effective in destroying vegetative cells of microorganisms of public
health significance, and in substantially reducing numbers of other undesirable microorganisms,
105

Contains Nonbinding Recommendations
Draft-Not for Implementation
but without adversely affecting the product or its safety for the consumer.” (21 CFR 112.3).
Sanitizing can include the use of such substances as hypochlorite, chlorine dioxide, iodine,
quaternary ammonium compounds, hot water, steam, dry heat, or ultraviolet light (Ref. 15) (Ref.
39) (Ref. 93) (Ref. 119).
You should consider the following list of factors that influence the effectiveness of cleaning
procedures:
•

The pressure of water or air used during debris removal (e.g., pre-rinse and post-rinse
for wet cleaning). Overly low pressure could not effectively remove soil or debris from
surfaces. However, if you are using high pressure when cleaning, you should take care to
not spread contamination from one surface (e.g., floors, floor drains) to another, which
can occur through splashing or aerosolizing (Ref. 18) (Ref. 66) (Ref. 134).

•

The material (e.g., plastic, stainless steel, concrete) of the surface to be cleaned and the
method of construction of the equipment and tools (e.g., solid welded, bolted for
disassembly). We provide draft guidance on equipment and tool construction and its
effect on cleanability in the section of this chapter titled, “Design, Construction, and
Workmanship.”

•

The force and duration of physical scrubbing. Low rates of force applied or short
amounts of time spent scrubbing equipment and tools could result in only partial removal
of soil and debris. On the other hand, overly aggressive or prolonged cleaning processes
could damage equipment and tool surfaces, potentially resulting in surface scratches or
other damage, which can serve as harborage sites for pathogens (Ref. 96) (Ref. 97) (Ref.
125).

•

The type and concentration of the cleaning agent or detergent. You should refer to the
label directions and manufacturer instructions for your detergents and other cleaning
agents to ensure you use a concentration and method effective for your use, including the
type of soil, residue, or material targeted for removal.

•

The contact time of the cleaning solution with the surface being cleaned. Shortened
contact time could result in only partial removal of soil and debris (e.g., the cleaning
agent could not be able to fully loosen the debris from the surface or could leave a film or
residue on your equipment or tools) (Ref. 38) (Ref. 97) (Ref. 125).

•

The characteristics and quantity of the soil and debris on the surface being cleaned.
Certain types of residues (e.g., oily or high protein) or large quantities of residues can
impact the need to modify the other factors described above (e.g., use a highly alkaline
detergent or a highly oxidizing cleaner for certain residues or increase contact time and
physical scrubbing) (Ref. 97) (Ref. 125).

When choosing a sanitizing treatment, if one is appropriate and necessary, you should consider
the following factors that influence their effectiveness, including:

106

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

The material of the surface to be sanitized. Some sanitizers are incompatible with some
materials (e.g., products containing chlorine could lead to the degradation of some
materials) (Ref. 93) (Ref. 125) (Ref. 105);

•

The type, duration, application method, temperature and concentration of the sanitizing
or antimicrobial treatment (Ref. 15) (Ref. 38). You should refer to the label directions
and manufacturer instructions to ensure you use a concentration and method effective for
your use;

•

The contact time of the sanitizing or antimicrobial treatment with the surface being
treated. Shortened contact time could cause incomplete treatment and excessive contact
time could damage your equipment or tools (Ref. 38) (Ref. 125); and

•

Characteristics of the water you use to prepare the sanitizing agent. The hardness (i.e.,
presence of minerals), pH, and temperature of your water could impact the effectiveness
of the sanitizing agent and its compatibility with the surface being sanitized (Ref. 38)
(Ref. 39) (Ref. 125) (Ref. 126).

The following steps are an example of a typical wet cleaning and sanitizing procedure (Ref. 94)
(Ref. 125); some steps could not be applicable to your operation or could be modified (Ref. 38)
(Ref. 94):
1. Pre-Clean: personnel use tools such as brushes, brooms, scrapers, and collection pans to
remove heavy residue, plant material or debris from the equipment or tools.
2. Initial Rinse: personnel rinse the equipment or tools with water to remove additional
organic material and residue that was loosened during the pre-clean step; scrubbing could
be necessary during this step.
3. Washing with Cleaning Agent and Mechanical Action: personnel apply a cleaning agent
in one of several forms, such as by spray or foam; personnel should ensure full coverage
of the relevant surface with the cleaning agent for the time and at the temperature
specified by the cleaning agent manufacturer; small equipment or tools or components of
these can be washed in sinks or tanks containing a solution of the cleaning agent;
mechanical action (e.g. scrubbing) ordinarily should be applied, using tools such as
brushes or scouring pads, in order to fully remove organic material and residues.
4. Post-Rinse: personnel apply water to remove loosened soil and debris along with the
cleaning agent; after the post-rinse the equipment and tools could be allowed to dry prior
to further activities.
5. Inspection: personnel check the equipment or tools for any remaining soil or residue;
additional draft guidance on equipment and tool inspection is found in the section of this
chapter titled “Inspection.”
6. Sanitize: when necessary and appropriate, personnel apply antimicrobial treatments to
clean, rinsed surfaces. Sanitizing is generally not effective unless it is preceded by a
107

Contains Nonbinding Recommendations
Draft-Not for Implementation
cleaning step, because residual organic material can protect pathogens from the action of
the sanitizing treatment (Ref. 94) (Ref. 38) (Ref. 39) (Ref. 82) (Ref. 93). Antimicrobial
treatments should be applied so that the treatment contacts all areas of the food contact
surface. Care should be taken to ensure contact of the treatment with hard to reach places
(e.g., edges of interlocking conveyor systems, gears and sprockets that contact covered
produce, and the undersides of guards, covers, and ceilings, from which moisture could
drip or drain onto the covered produce). This could be done by immersion (e.g., for small
equipment and tools and their components), spraying, or flushing (e.g., for stationary
equipment). You should consult the labeled instructions provided by the supplier. In
some instances, antimicrobial treatments should be followed by rinsing.
Dry cleaning typically involves a pre-cleaning step to remove heavy residue, plant material, and
debris, followed by a dry-cleaning step using mechanical action to further remove organic
material and residue. Tools that are typically used for dry cleaning include vacuum systems,
brushes, scrapers, and compressed air. An inspection should also be performed after dry
cleaning to evaluate the effectiveness of the cleaning process. Generally, there are fewer options
available for routine sanitizing of dry cleaned equipment and tools, and these may not be suitable
for all circumstances.
Frequency of Cleaning and Sanitizing
You should evaluate and establish cleaning frequencies for both food contact and non-food
contact surfaces, as well as sanitizing frequencies for food contact surfaces, as necessary and
appropriate. You should schedule cleaning and sanitizing of equipment and tools with food
contact surfaces after storage, after relevant production cycles (e.g., daily or between shifts), or
as otherwise necessary to protect against contamination of covered produce. In some cases, you
could determine that cleaning for both the non-food contact surfaces and the food contact
surfaces of equipment and tools should occur at the same frequency.
The following are some factors that you should consider when determining the frequency of
cleaning and, when necessary and appropriate, sanitizing:
•
•
•
•
•
•
•

Visual observations of the rate of accumulation of soil and debris;
Whether the surface is a food contact surface;
Whether the equipment or tools also are used for excluded produce (food contact surfaces
of such equipment and tools must be adequately cleaned and sanitized, as necessary,
before use on covered produce (21 CFR 112.111(b));
The potential for contamination of the equipment or tool during use (e.g., more frequent
cleaning and sanitizing could be necessary if a field-coring device regularly contacts the
soil than if it is held away from the soil);
The duration of the production cycle (e.g., 8, 12, 16 hours);
Ambient temperature during use of the equipment and tools (the rate bacterial growth
increases as temperature increases) (Ref. 38) (Ref. 126);
The ability of produce residues to support the growth of pathogens (most support growth,
but the rate of growth can be influenced by differences in moisture, water activity,
nutrients, and inhibitory substances) (Ref. 38) (Ref. 126);
108

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

•

The design, construction, and workmanship of the equipment and tools (Ref. 38) (Ref.
94) (Ref. 125) (Ref. 134) (e.g., more frequent cleaning and sanitizing could be necessary
for a conveyor system with interlocking belt pieces compared to a system with a singlepiece, smooth belt because there could be a greater potential for accumulation of debris
between the interlocking pieces); and
The results of any testing that you perform (e.g., results showing high levels of microbial
indicator organisms could necessitate more frequent cleaning).

You should consider the accumulation of soil, residue, or material during your covered activities
and the potential for pathogen growth as you determine appropriate cleaning and sanitizing
frequencies. You could find it useful to schedule periodic deep cleaning and sanitizing, as
necessary and appropriate, procedures (i.e., beyond routine procedures) at a reduced frequency in
comparison to your routine procedures.
You should consider performing a sanitizing step each time that you perform a complete wet
cleaning procedure (e.g. steps 1-5 described in the section of this chapter titled “Cleaning and
Sanitizing Procedures”) for equipment or tools. The process of cleaning followed by sanitizing
enhances microbial removal and inactivation (Ref. 38) (Ref. 83) (Ref. 93) (Ref. 94). Further,
depending on your established cleaning process, you could determine that performing a pre-clean
step, or some portion of your cleaning procedures, should be performed at an increased
frequency compared to that of the entire cleaning process to address heavy accumulation of
residue (e.g., leaves, soil and other material) that could build up over the course of use. For
example, a farm conveys cucumbers into a packing area; the farm’s procedures could specify
that the pre-cleaning step be performed at least twice during a production shift to control
accumulation of mud, stems, and other debris, and that a complete wet cleaning cycle, including
sanitizing, be performed at the end of each day.
In some limited instances, you could determine that sanitizing food contact surfaces can occur at
a reduced frequency compared to cleaning activities, particularly after dry cleaning. For
example, if a farm that shells and packs walnuts determines that the shelling area should remain
dry, the farm could determine that the shelling equipment should be dry cleaned daily, using
brushes and compressed air to remove organic material and residue; this avoids introducing
moisture from wet cleaning, which could increase the potential for pathogen growth and transfer.
Further, the farm could determine that prior to the beginning of covered activities each season, or
at a specified frequency, the shelling equipment should be disassembled, moved to a location
outside of the dry production environment, wet cleaned, and the food contact surfaces sanitized;
after thorough drying, the equipment would be reassembled in the production area.
You should also determine potential instances when cleaning and sanitizing of equipment or
tools should occur outside your scheduled frequency. You should ensure that cleaning and
sanitizing of food contact surfaces and non-food contact surfaces of equipment and tools occurs
immediately when you discover or suspect that they are potentially contaminated (e.g., after
contact with human or animal excreta, contaminated water, contaminated produce, excluded
produce, or contaminated hands). For example, your procedures specify that a piece of
equipment used for conveying gooseberries is cleaned and sanitized at the end of each
production cycle; there could be circumstances where cleaning and, when necessary and
appropriate, sanitizing the equipment must be performed before the scheduled time at the end of
109

Contains Nonbinding Recommendations
Draft-Not for Implementation
the production cycle, as reasonably necessary to protect against contamination. (See 21 CFR
112.123(d)(1)).
Transport Equipment
If you use equipment such as pallets, forklifts, tractors, and vehicles such that they are intended
to, or likely to, contact covered produce, you must do so in a manner that minimizes the potential
for contamination of covered produce or food contact surfaces with known or reasonably
foreseeable hazards. (21 CFR 112.123(e)). Equipment subject to subpart L that you use to
transport covered produce must be adequately clean before use in transporting covered produce,
and adequate for use in transporting covered produce. (21 CFR 112.125).
You should identify the equipment used to transport covered produce, which could include
trucks. If you determine that the transport equipment is not adequately clean, you could, for
example, clean the equipment or choose to not use it. You should pay particular attention to the
surfaces that contact covered produce.
Instruments and Controls
Instruments or controls you use to measure, regulate, or record temperatures, hydrogen-ion
concentration (pH), sanitizer efficacy or other conditions, in order to control or prevent the
growth of microorganisms of public health significance, must be: accurate and precise as
necessary and appropriate in keeping with their purpose; adequately maintained; and adequate in
number for their designated uses. (21 CFR 112.124). Examples of these instruments include pH
meters or test strips; iodine test strips; chlorine test strips; oxidation-reduction potential meters;
indicating thermometers; recording thermometers; thermocouples, and temperature actuated
control valves. These instruments could be used to measure or record such conditions as
temperatures in composting piles; pH in composting piles; or the concentration of antimicrobial
in a sanitizing solution.
Personnel to whom you assign the responsibility for maintaining these instruments and controls,
or who are engaged in the supervision thereof, should understand your procedures. These
personnel should understand the importance of accuracy and precision, and should ensure that
accurate measurements are collected. You should specify when personnel need to inform a
supervisor or other responsible party of certain observations so they can determine appropriate
steps. You should direct supervisors or responsible parties, as applicable, to ensure that activities
related to instruments and controls are conducted in accordance with your procedures and
corrections are made as needed.
Accuracy and Precision
The accuracy and precision of your instruments and controls help to ensure the efficacy of
measures to control or prevent the growth of microorganisms of public health significance on
your farm. Accuracy is how close a device’s displayed measurement compares to the true value.
For example, if your thermometer displays a reading of 75.2°F (24°C) when placed in a
container of water and the true temperature of the water is 85.2°F (29°C), your instrument is not
very accurate. Precision is the consistency among individual measurements displayed by an
110

Contains Nonbinding Recommendations
Draft-Not for Implementation
instrument under the same conditions. For example, if you weighed a single watermelon 5 times
on the same scale and the scale read 20.2 lbs., 18.9 lbs., 21.4 lbs., 19.5 lbs., and 22.8 lbs., the
scale is not very precise. Continuing with the first example, if your thermometer reads 75.2°F
(24°C), 75.2°F (24°C), and 75.2°F (24°C) for three measurements of 84.2°F (29°C) water, the
instrument is precise, but not accurate.
You should evaluate your farm’s covered activities for which you use instruments or controls to
measure, regulate, or record conditions to control or prevent the growth of microorganisms of
public health significance. The necessary degree of accuracy and precision for your instruments
or controls varies depending on how they are used. For example, an instrument that is both
highly accurate and highly precise (e.g., within 2°F (1°C)) should be used when small variations
can lead to the growth of pathogens, such as when using a thermometer to measure storage
temperature in a cooler that contains mushrooms in oxygen impermeable packages. In this
example, the farm should target maintaining temperatures below 36°F (2.2°C) because a
temperature above 38°F (3.3°C) during storage can result in the formation of Clostridium
botulinum toxin (Ref. 76) (Ref. 118) (Ref. 123).
As part of your maintenance activities, you should perform periodic accuracy checks to ensure
that your instruments and controls are functioning properly. In some cases, you can check the
accuracy and precision of your instruments and controls yourself. Generally, accuracy checks
involve comparing an instrument’s displayed measurement against at least one true value. In
some instances, you could be able to account for minor, consistent deviations in instrument
readings. For example, if a farm uses a thermometer to check the temperature of turned compost
under a process based on the example provided in 21 CFR 112.54(b)(2) to maintain aerobic
conditions at a minimum of 131°F (55°C) for 15 days, and determines that the thermometer
consistently reads within 4°F of the true value during accuracy checks; the farm should account
for this level of accuracy by targeting a temperature reading that is sufficiently high to ensure
that it meets the target (e.g., maintain at least 135°F (57°C)). You should adjust or replace any
of your instruments or controls that do not meet your identified level of accuracy or precision.
Documentation or manuals that typically accompany instruments and controls often contain
information on the instrument’s accuracy. You could, for example, contact the vendor or
manufacturer directly to obtain additional information on the accuracy and precision of an
instrument or control. You could also choose, for example, to seek further information from
technical assistance resources.
You should establish a calibration schedule for all of the instruments and controls that you use to
measure, regulate, or record temperatures, hydrogen-ion concentration (pH), sanitizer efficacy,
or other conditions, to control or prevent the growth of microorganisms of public health
significance. You should replace instruments or controls that you cannot calibrate to the
necessary level of accuracy or precision. Many instrument and control vendors and
manufacturers recommend periodically calibrating instruments, and can provide instructions and
recommended frequencies for these procedures.
Calibration involves comparing an instrument’s displayed measurement against multiple, true
values, often using a known reference standard (e.g., National Institute of Science and
Technology (NIST) traceable instrument or other recognized reference solutions or instruments)
111

Contains Nonbinding Recommendations
Draft-Not for Implementation
and a notation of the extent to which the measurement deviates from the standard. You should
use multiple true values, with at least one true value typical of the instrument’s use. For
example, pH probes are typically calibrated against two reference solutions, using at least one
solution that reflects a value typically measured by the instrument when used. As another
example, if you are calibrating a thermometer that you typically use to measure temperatures of
compost near 131°F, you should use at least one calibration true value near 131°F. Calibration
can also involve an adjustment to correct the accuracy deviation, depending on the instrument
design. For example, you can check a dial thermometer for accuracy by measuring the
temperature it displays when placed in an ice slurry (32°F (0°C)) or boiling water, accounting for
your elevation (e.g., 212°F (100°C) at sea level). You could calibrate the thermometer by
placing it and a NIST traceable instrument in an ice slurry and boiling water and comparing the
temperature displayed by each. You could then adjust your thermometer, if its design allows, to
display a reading consistent with that of the NIST instrument. If your thermometer cannot be
adjusted, then you should account for the difference between the thermometer and the NIST
traceable instrument when you use the thermometer. You can calibrate your instruments and
controls yourself or use a third-party, such as a manufacturer or contract laboratory.
Calibration is important to ensure accurate results that are consistent over time. Instrument wear
or damage can result in changes in accuracy or precision. The extent to which an instrument or
control will maintain its accuracy and precision between calibrations depends on the type of
instrument; instrument quality; frequency of use; use and storage environment (e.g., high
humidity and temperature can affect some instruments and controls); and the way the instrument
is used (e.g., rough handling can affect instruments and controls). In some instances, you should
periodically compare results against a more reliable instrument (e.g., periodic checks with a pH
probe when typically using pH test strips), especially when there is potential for human error or
judgement associated with qualitative results (e.g., color change in a pH test strip).
You should maintain all instruments and controls according to the manufacturer’s
recommendations. Maintenance could include: performing start-up activities prior to taking
measurements; performing instrument or control cleaning steps between measurements, such as
flushing residual material from the instrument or control; and confirming expiration dates of the
instruments, controls or associated materials. Failure to maintain instruments can lead to
inaccurate or imprecise readings. For example, an expired test kit used to measure the
concentration of sanitizing solution could provide an inaccurate measurement, possibly
impacting the efficacy of your sanitizing procedures. You should perform maintenance activities
at appropriate frequencies to ensure that your instruments and controls function in the manner
necessary to control or prevent the growth of pathogens. For example, you should instruct your
personnel to periodically check expiration dates, and not use expired instruments, test kits, test
kit solutions, and instrument and control components.
Storage methods could impact the functionality of some instruments and controls. For example,
the probe of a pH meter should not be stored in water, which can damage the probe and result in
inaccurate readings. Further, humidity or temperature can impact the accuracy of some test kits
and reagents; these types of instruments or controls should be stored under climate-controlled
conditions until use.

112

Contains Nonbinding Recommendations
Draft-Not for Implementation
Adequate in Number
You must have enough instruments on your farm to facilitate measurement (See 21 CFR
112.124) and should have those instruments placed in appropriate locations to ensure control of
your processes. You should determine the appropriate number and appropriate placement of
instruments and controls given the scale of your farm’s activities. You should have sufficient
numbers of instruments or controls conveniently located, so they are available when needed. For
example, if you perform treatment of biological soil amendments of animal origin (BSAAO),
such as composting, at multiple sites of your farm, you should determine the number of
thermometers necessary at each site so that your personnel can ensure that the compost meets
any relevant temperature standards to comply with 21 CFR 112.54. As another example, if you
have multiple growing or packing locations on your farm, you should have enough test kits so
that your personnel can check the strength of a sanitizing solution at all of those locations where
testing is necessary.
In some cases, you could need multiple instruments in order for them to be adequate in number
for their designated uses. For example, if you are composting a small biological soil amendment
of animal origin (BSAAO) pile and monitoring the temperature, one thermometer placed near the
bottom of the pile where temperature is more challenging to control could be sufficient.
However, if you are composting large windrows, you could need multiple thermocouples placed
throughout the pile at different depths to evaluate the overall temperature.

2. Buildings
Buildings that are subject to subpart L of the Produce Safety Rule include any fully- or partiallyenclosed building used for covered activities, including minimal structures that have a roof but
do not have any walls. (21 CFR 112.122(a)). Buildings that are subject to subpart L also include
storage sheds, buildings, or other structures used to store food contact surfaces (such as harvest
containers and food–packing materials) (21 CFR 112.122(b)). Such buildings could be
permanent or temporary structures. Partially-enclosed buildings typically have a roof, with one
or more sides open to the natural environment while fully-enclosed buildings have walls on all
sides, a floor, and a roof. You should identify all fully- and partially-enclosed buildings on your
farm that you use for a covered activity. Buildings on your farm in which you do not perform
covered activities, and which are, therefore, not covered by subpart L could include, for example:
personal homes; grain silos; livestock barns; chicken coops; and stables.
Size, Construction, and Design
Your buildings that are subject to subpart L must be suitable in size, construction, and design to
facilitate maintenance and sanitary operations for covered activities to reduce the potential for
contamination of covered produce or food contact surfaces with known or reasonably foreseeable
hazards. (21 CFR 112.126(a)(1)). The buildings must:
(i) provide sufficient space for placement of equipment and storage of materials; and
(ii) permit proper precautions to be taken to reduce the potential for contamination of
covered produce, food contact surfaces, or packing materials by effective design
113

Contains Nonbinding Recommendations
Draft-Not for Implementation
including the separation of operations in which contamination is likely to occur,
by one or more of the following means: location, time, partition, enclosed
systems, or other effective means. (See 21 CFR 112.126(a)(1)(i) and (ii)).
What constitutes suitable size, construction, and design for a building largely depends on the
building’s use for covered activities. You should evaluate whether your identified buildings’
size, construction, and design are appropriate, considering the covered activities performed and
operating conditions in each building. You should consider factors such as drainage, ventilation,
facilitation of pest control and whether there is sufficient space for free movement around any
equipment. For example, for a partially-enclosed building that a farm uses during the off season
to store harvesting equipment that contacts covered produce, the farm should evaluate whether
the building provides sufficient space for storage of the equipment and for maintenance of the
building (e.g., pest control, removal of debris) to minimize the potential for contamination.
You should ensure that the construction of your buildings facilitates the maintenance of sanitary
conditions. Windows, doors, and roofs of fully-enclosed buildings should prevent leaks and the
entry of dirt, dust, debris, and pests. Buildings should also allow access for examination and
maintenance of equipment contained within the building and the building itself. For example, if
you choose to have a drop ceiling in a fully enclosed building used for packing, then the building
should be constructed in a way that allows access to the space between the roof and the drop
ceiling for maintenance and sanitary operations, such as pest control activities.
Building materials and construction should be durable enough to withstand their use in order to
reduce the potential for contamination. You should evaluate your building’s materials and
construction, and periodically visually assess your buildings. For example, floors should be able
to withstand expected foot traffic and movement of equipment and vehicles without becoming
damaged and potentially harboring pathogens, and doors and walls should be durable enough to
withstand typical impacts by personnel and transport equipment without becoming damaged or
permitting pest entry.
To ensure that the size and design of your buildings facilitates maintenance and sanitary
operations, you should consider: the activities that occur within the building; the volume and
frequency of activity within the building; the number, size, and placement of equipment and
tools used or stored within the building; and the number of people (e.g., personnel, supervisors,
visitors, contractors) using the building at any given time. For a building to be suitable in size, it
should have enough room for covered activities to be conducted without contact between
covered produce or food contact surfaces and building materials, non-food contact surfaces, or
clothing.
When installing or placing equipment in your buildings, you should be aware of the area
surrounding the equipment to ensure that personnel can easily perform inspections, maintenance,
and cleaning and sanitizing activities. See the subsection of this chapter titled “Installation and
Maintenance” for further draft guidance on equipment placement.
Example 7q: A farm that uses a conveyor belt in a packinghouse should ensure that there is
enough space between the conveyor equipment and the wall or adjacent equipment to allow
personnel to easily access the entire length of the conveyor belt. This should include access
114

Contains Nonbinding Recommendations
Draft-Not for Implementation
to: the conveyor belt; the support frame; the points at which the framework is secured to the
floor of the building; and any surfaces that could contact, or from which water could drip or
drain onto, covered produce or food contact surfaces.
Example 7r: In a fully enclosed building dedicated to packing covered produce, you should
set up operations such that you can efficiently remove the trash without touching food
contact surfaces.
Example 7s: If both clean and used harvest containers are stored in a partially-enclosed
storage shed, the farm must ensure that there is enough space in the area to separate the
containers to reduce the potential for contamination. (See 21 CFR 112.126(a)(1)).
There are multiple ways to ensure that building design separates your operations to reduce the
potential for contamination. You can, for example, use careful layout and installation of
equipment within buildings to reduce the potential for contamination, such as by installing
physical barriers to separate activities, or dedicating areas to specific activities, with sufficient
space or barriers between them. For another example, the areas where covered produce are
prepared for distribution (i.e., finished product) should not be immediately adjacent to areas
where covered produce from the field are washed in a way that water splash could be transferred
to the finished product. When you identify the need to separate certain activities, you should
ensure that personnel are aware of and understand your procedures that specify the separation to
prevent contamination.
Preventing Contamination, Including Floors, Walls, and Ceilings
You must implement measures to prevent contamination of your covered produce and food
contact surfaces in your buildings, as appropriate, considering the potential for such
contamination through floors, walls, ceilings, fixtures, ducts, or pipes; and drip or condensate.
(21 CFR 112.126(b)). Surfaces of buildings that are not adequately cleaned have the potential to
become a source of contamination (Ref. 51) (Ref. 72). You should evaluate your buildings and
their components (e.g., floors, walls, ceilings, ducts, pipes, fixtures, drains), including periodic
visual assessments. You should repair or replace damaged or defective building components that
have the potential to contaminate covered produce or food contact surfaces.
Examples of measures that you should take, as appropriate, include:
•
•
•
•
•
•

Repairing piping systems that are leaking onto covered produce or food contact surfaces;
Repairing roofs, walls or floors with holes or cracks in them;
Protecting covered produce and food contact surfaces from condensate from ceilings and
overhead pipes, or maintaining such surfaces in a sanitary condition if they are subject to
the formation of condensation so that they do not serve as a source of contamination;
Protecting drains from becoming harborage sites for pathogens;
Cleaning and sanitizing building components as necessary to reduce the potential for
contamination; and
If you use high pressure hoses in your cleaning activities, ensuring that water splash does
not spread contaminants from floors, walls, ceilings, fixtures, ducts, or pipes to covered
produce or food contact surfaces, or ensuring that maintenance, cleaning and sanitizing, if
115

Contains Nonbinding Recommendations
Draft-Not for Implementation
necessary and appropriate, procedures address such surfaces if they are subject to such
water splash so that they do not serve as a source of contamination.
Covered produce and food contact surfaces can be protected from dripping condensate using
practices such as: routing condensate to drains, drip pans, or areas away from covered produce
and food contact surfaces; not storing covered produce or food contact surfaces under or near
areas identified as likely condensate areas or “drip zones”; covering covered produce and food
contact surfaces to protect them from condensate; and controlling the humidity in your building
(e.g., through ventilation) to minimize the formation of condensate.
Ceilings, overhead pipes, walls, floors and drains can be maintained in a sanitary condition by
ensuring that their surfaces are of a design, construction and workmanship such that they can be
adequately cleaned and properly maintained (see the section of this chapter titled “Design,
Construction and Workmanship”) and by cleaning, and, when necessary and appropriate,
sanitizing them (see the section of this chapter titled “Cleaning and Sanitizing Equipment and
Tools”). In cases where condensate contacts your covered produce or food contact surfaces, you
should consider the originating surface of the condensate a food contact surface, and you should
evaluate whether measures to address any potentially contaminated covered produce or food
contact surfaces are necessary.
Floor drains are known to serve as harborage sites for Listeria monocytogenes (Ref. 19) (Ref.
88), likely due to their cool, wet environment and the tendency for drain cleaning and sanitizing
to be overlooked or inadequate (Ref. 19) (Ref. 87). You should clean and sanitize drains in a
way that that prevents harborage of contamination and minimizes the likelihood that water splash
or aerosols will contact covered produce or food contact surfaces (e.g., cleaning drains after
packing operations end and not using high pressure water rinsing).
Drainage
You must provide adequate drainage in all areas where normal operations release or discharge
water or other liquid waste on the ground or floor of the building. (21 CFR 112.126(a)(2)). The
drainage system, including the drain grate, should accommodate the rate of release or discharge
during peak operations. Your buildings could need multiple drains to prevent standing water or
slow drainage.
We acknowledge the potential for small pools of water to temporarily form on the floor of
buildings used for growing activities, and that pooling of water of this nature, which is temporary
and could occur in the normal course of watering practices, is not reasonably likely to contribute
to the contamination of covered produce. We are not suggesting that it will always be possible to
eliminate pooling. Avoiding pooling by careful control of greenhouse watering practices with
consideration to your drainage system is ideal; however, to the extent pooling could be inevitable
or could sometimes occur, despite adequate drainage, we expect covered farms to take steps to
protect covered produce from any contamination that could build in the pooled water.

116

Contains Nonbinding Recommendations
Draft-Not for Implementation
Pest Control
You must take those measures reasonably necessary to protect covered produce, food contact
surfaces, and food-packing materials from contamination by pests in buildings, including routine
monitoring for pests as necessary and appropriate. (21 CFR 112.128(a)). You should evaluate
your buildings in which you perform covered activities to determine what measures are
necessary.
For fully-enclosed buildings, you must take measures to exclude pests from your buildings. (21
CFR 112.128(b)). You should prevent pest entry (e.g., cover or repair holes in the building) and
reduce pest attractants (e.g., debris for nesting, food scraps, pooled water) in such buildings and
their immediately surrounding areas. For partially-enclosed buildings, you must take measures
to prevent pests from becoming established in your buildings (such as by use of screens or by
monitoring for the presence of pests and removing them when present). (21 CFR 112.128(c)).
You should minimize pest attractants and harborage areas in and around your buildings,
including accumulated litter and debris; food scraps; nesting material; unused equipment; waste
storage; tall, dense foliage, weeds, and grass; and pooled water (see the section of this chapter
titled “Drainage”). You should visually assess potential points of entry and potential routes of
pest movement. Your first inspection can be used to guide your monitoring activities. Your
monitoring frequency (e.g., weekly, monthly, bi-monthly) should be based on several factors,
including the potential for pest activity, environmental conditions, and the level of observed pest
activity in or around your buildings. Your monitoring could assist you in identifying areas of
concern that you had not previously identified (e.g., you could identify a crack in the foundation,
through which insects could enter, that developed after the previous inspection).
During your monitoring activities, assigned personnel should look for pest attractants, points of
pest entry, signs of pest activity, both inside and immediately outside of the building and, when
found, attempt to identify the type of pest (e.g., bird, rodent, insect), and the extent of the
activity. Signs of pest activity might include the presence of the following:
•
•
•
•
•
•

Animal excreta (e.g., rodent pellets, bird droppings, urine);
Nests (e.g., bird, rodent);
Gnaw marks on materials or shredded materials (e.g., produce, packing materials, paper,
plastic, wood);
Burrows, trails, or other evidence of pest movement (e.g., worn paths or grease marks), or
tracks outside the building;
Insects (e.g., flies, larvae, ants) inside the building; and
Remains of dead pests.

If you observe signs of pest activity, you should identify and address the contributing factors
related to the pest activity. You also should evaluate the potential for contamination of covered
produce, food contact surfaces, and food-packing materials, and determine whether measures to
address any potentially contaminated covered produce or food contact surfaces are necessary.
If you identify pest infestation, 21 CFR 112.128(a) requires that you take those measures
reasonably necessary to protect covered produce, food contact surfaces, and food-packing
117

Contains Nonbinding Recommendations
Draft-Not for Implementation
materials from contamination. This can include strategies for their elimination or to prevent
them from becoming established, such as installing: indoor rodent traps (e.g., catch-and-release
traps, snap traps, glue boards); outdoor rodent traps and bait stations anchored to the perimeter of
the building; insect glue boards; light traps; and electronic flying-insect killers. These could be
placed in areas of high pest activity, suspected points of entry, and nesting sites, but should be
placed away from covered produce, food contact surfaces, and food-packing materials. If you
use pest traps or bait stations, you should check them periodically (e.g., weekly) for signs of
activity, replace any that become lost or damaged, remove any dead pests, and replace any
missing bait. If you use pesticides, you should ensure that you use all pesticides and pesticide
devices in accordance with all applicable Federal, state, and local laws.
Personnel to whom you assign the responsibility of pest monitoring, or who are engaged in the
supervision thereof, should understand your procedures related to pest control. You should
specify when personnel need to inform a supervisor or other responsible party of certain
observations so they can determine appropriate steps. You should direct supervisors or
responsible parties, as appropriate, to ensure that activities related to pest control are conducted
in accordance with your procedures and corrections are made as needed.
Domesticated Animals
Domesticated animals could be present on your farm for a variety of reasons, including work
(e.g., horses, mules), protection (e.g., guard dogs), and personal companionship (e.g., family
pet). However, domesticated animals can carry pathogens, such as Salmonella spp. (Ref. 6)
(Ref. 110) (Ref. 129); and pathogenic strains of E. coli (Ref. 13) (Ref. 103) (Ref. 110) (Ref.
143), and serve as sources of contamination of covered produce and food contact surfaces (Ref.
71) (Ref. 77) (Ref. 78) (Ref. 90) (Ref. 117). You must take reasonable precautions to prevent
contamination of covered produce, food contact surfaces, and food-packing materials in fullyenclosed buildings with known or reasonably foreseeable hazards from domesticated animals
(e.g., cats, dogs, horses, chickens) by: (1) excluding domesticated animals from fully-enclosed
buildings where covered produce, food contact surfaces, or food-packing materials are exposed;
or (2) separating domesticated animals in a fully enclosed building from an area where a covered
activity is conducted on covered produce by location, time, or partition. (21 CFR 112.127(a)).
You should refer to Chapter 5: Domesticated and Wild Animals (Subpart I) of this document for
additional draft guidance on domesticated and wild animals related to outdoor areas and
partially-enclosed buildings.
You should evaluate the presence and purpose of the domesticated animals on your farm and
visually assess their actions when determining reasonable precautions to prevent contamination
in your fully enclosed buildings. When excluding domesticated animals from buildings, you
should keep all entryways, including windows and doors closed whenever it is not necessary for
them to be open. Windows should be screened to help prevent domesticated animal entry. If
you choose to satisfy the requirements of 21 CFR 112.127(a) through exclusion and there are
times when entryways need to remain open, you should have a system in place to prevent
domesticated animal entry. For example, for those times when a loading dock door remains
open, you could, for example, designate a worker assigned to that area to monitor and prevent
entry of domesticated animals to the area, and to remove any that enter. Alternatively, you

118

Contains Nonbinding Recommendations
Draft-Not for Implementation
could, for example, use gates or access limitation devices that domesticated animals are unable to
maneuver (e.g., Dutch doors or gates that domesticated animals cannot jump over).
In some instances, exclusion of domesticated animals from an entire, fully-enclosed building
could be impractical, such as when the building has multiple rooms, only some of which are used
for covered activities. If you do not exclude domesticated animals from the entire building, you
must separate them from areas where covered activities are conducted on covered produce by
location, time, or partition (21 CFR 112.127 (a)(2)). For example, you could allow animals to
visit an administrative office that is separated by a wall that prevents access to the portion of the
building in which packing activities occur. For another example, in entryways to areas of the
building in which covered activities are conducted on covered produce, self-closing doors can be
used to prevent entrance of domesticated animals. You also, for example, could separate
portable equipment and tools that contact covered produce or food-packing materials by storing
such equipment and tools in closed cabinets in rooms that domesticated animals can access.
Finally, your procedures could permit domesticated animals in areas in which covered activities
occur, at times when those activities are not taking place. In these instances, you should clean
and, when necessary and appropriate, sanitize, exposed equipment, tools, floors, and walls of the
room where the domesticated animals were present, before resuming use of the room for a
covered activity. See the section of this chapter titled “Cleaning and Sanitizing Equipment and
Tools” for further draft guidance.
Personnel who manage or interact with domesticated animals, or who are engaged in the
supervision thereof, should understand your procedures related to reasonable precautions to
prevent contamination of covered produce and food contact surfaces from domesticated animals
in your fully enclosed buildings. You should direct supervisors or responsible parties, as
applicable, to ensure that personnel conduct activities in accordance with your procedures, and
corrections are made as needed.
Guard or guide (i.e., service) dogs could be allowed in some areas of a fully-enclosed building if
the presence of the dog is unlikely to result in contamination of produce, food contact surfaces,
or food-packing materials. (21 CFR 112.127(b)). Guard or guide dogs present in areas where
covered produce, food contact surfaces, or food-packing materials are exposed should be under
the control of a handler. You should ensure that guard or guide dogs, including their fur, saliva,
or skin, do not contact covered produce, food contact surfaces, or food-packing materials. For
example, you should not permit guard or guide dogs to: run throughout the building; jump onto
equipment or tools that contact covered produce; contact the hands of personnel that contact
covered produce; or contact covered produce. You should inform guard and guide dog handlers
of the potential for dogs to carry contamination into your buildings and ensure that they
minimize the likelihood of the dogs becoming contaminated (e.g., contact with animal excreta)
before entering your buildings.

3. Other Sanitation Measures
The other sanitation provisions of the Produce Safety Rule (21 CFR 112.129 - 134) include the
management of animal excreta and litter from domesticated animals, toilet facilities; handwashing facilities; sewage; trash, litter, and waste; and plumbing.
119

Contains Nonbinding Recommendations
Draft-Not for Implementation
Animal Excreta and Litter from Domesticated Animals
If you have domesticated animals, to prevent contamination of covered produce, food contact
surfaces, areas used for a covered activity, agricultural water sources, or agricultural water
distribution systems with animal waste, you must (1) adequately control their excreta and litter;
and (2) maintain a system for control of animal excreta and litter. (21 CFR 112.134). For
example, you would comply with this provision by not locating manure piles adjacent to packing
sheds in which covered produce is exposed.
Draft guidance on related requirements is provided in: this chapter (related to 21 CFR 112.127);
Chapter 5: Domesticated and Wild Animals (Subpart I) (related to 21 CFR 112.83); and Chapter
6: Growing, Harvesting, Packing, and Holding Activities (Subpart K) (related to 21 CFR
112.112). Depending on the number and types of domesticated animals on your farm, there are
different ways that you can manage the control of their excreta and litter.
For domesticated animals under your control, you should identify the areas in which the animals
are likely to produce excreta or litter (e.g., stalls, grazing pastures) and evaluate the potential for
contamination, including through runoff and transfer via personnel footwear, of your covered
produce, food contact surfaces, areas used for covered activities, agricultural water sources, or
agricultural water distribution systems. Additionally, you should evaluate how you store and
transport their excreta or litter, and the potential for contamination from these activities. You
should house and pasture these animals, and store their excreta or litter downhill and away from
areas of concern or by using berms, pits, or grading to contain runoff. For companion or guard
animals (e.g., dogs, cats) you could, for example, periodically inspect for excreta in the areas to
which they have access, collecting and disposing of it in waste containers.
Toilet Facilities
Human feces could contain pathogens in relatively high concentrations (Ref. 21) (Ref. 63) (Ref.
40). One of the most basic measures that you can take to prevent the transfer of pathogens from
human feces to covered produce and food contact surfaces is to provide toilet facilities to collect
and contain human feces and liquid waste. Toilet facilities include portable toilets, outhouses,
plumbed facilities, or other enclosed facilities where toilets are located.
Accessibility
You must provide personnel with adequate, readily accessible toilet facilities, including toilet
facilities readily accessible to growing areas during harvesting activities. (21 CFR 112.129(a)).
Note that 21 CFR 112.33(b) requires that you also make toilet and hand-washing facilities
available to visitors; see Chapter 3: Health and Hygiene (Subpart D) of this document. You
should consider personnel and visitor activities and traffic throughout your growing, harvesting,
packing, and holding areas to help you determine the appropriate number and locations of toilet
facilities to efficiently accommodate the typical numbers of individuals accessing certain areas at
the same time, such as at the beginning of work, or after a break. You should evaluate your toilet
facilities to determine whether they are easily accessible for personnel working in areas where
covered activities occur, including during all harvesting activities. You should ensure that toilet
facilities are within a reasonable walking distance from covered activities (e.g., approximately ¼
120

Contains Nonbinding Recommendations
Draft-Not for Implementation
mile or less). You could, for example, consider placing toilet facilities near designated personnel
break areas to facilitate their use. You should ensure that personnel are aware of the locations of
toilet facilities and know not to relieve themselves in the growing areas or in any area on your
farm other than a toilet facility.
Design, Location, and Maintenance
Toilet facilities must be designed, located, and maintained to prevent contamination of covered
produce, food contact surfaces, areas used for a covered activity, water sources, and water
distribution systems with human waste. (21 CFR 112.129 (b)(1)). You should evaluate your
toilet facilities to ensure that they have proper drainage and that backflow devices do not leak
sewage or liquid waste. Toilet facilities, including portable toilet facilities, should securely
contain or securely transport all sewage and liquid waste away from locations where covered
activities occur. For further draft guidance see the sections of this chapter titled “Sewage
Systems” and “Plumbing.”
Within fully or partially-enclosed buildings, your toilet facilities should be located and designed
in a way that minimizes the potential for transferring contamination by persons entering and
leaving the facilities. For example, in a building used for both packing activities and office
work, with the two areas separated, a toilet facility that is typically used by office and delivery
personnel and visitors, in addition to packing personnel, ideally could have one entryway from
the packing area and a separate entryway from the office area. This arrangement would
eliminate the need for office and delivery personnel and visitors to enter the packing area to use
the toilet facilities. You should consider toilet facilities as part of the overall size, construction,
and design of your buildings. See the subsection of this chapter titled “Buildings – Size,
Construction and Design.”
Runoff from toilet facilities has the potential to contaminate covered produce, soil, and irrigation
water (Ref. 1) (Ref. 25). The location of your toilet facilities should prevent contamination from
human waste and should facilitate containment and cleaning of any accidental spills or leaks.
For example, you could locate portable toilet facilities downhill from your growing area and
away from your water sources; or, you could, for example, use berms or grades to help protect
covered produce, areas where covered activities occur, and water sources and distribution
systems from contamination from uphill toilet facilities.
Your toilet facilities must be designed, located, and maintained to be directly accessible for
servicing, be serviced and cleaned at a frequency sufficient to ensure suitability of use, and be
kept supplied with toilet paper. (21 CFR 112.129(b)(2)). Sewage transport and other service
vehicles should have clear access to your toilet facilities to ensure proper collection and disposal
of human waste, minimizing the likelihood of spills or leakage. You should maintain your toilet
facilities in a sanitary condition. You should establish monitoring, servicing, and cleaning
procedures and schedules for toilet facilities. You should monitor toilet facilities at a frequency
that ensures that they remain sanitary and that they are supplied with toilet paper. Your
procedures should specify the frequency of these inspections, the personnel involved, and
conditions that should be reported to you, a supervisor, or responsible party. You should
encourage personnel to report any observed deficiencies of the toilet facilities to their supervisor

121

Contains Nonbinding Recommendations
Draft-Not for Implementation
or other responsible party. Tools and equipment used to clean toilet facilities should not be used
to clean surfaces where covered activities are performed.
Personnel to whom you assign the responsibility of maintaining toilet facilities, or who are
engage in the supervision thereof, should understand your procedures. You should direct the
supervisors or other responsible parties, as applicable, to ensure that monitoring and other
activities are conducted in accordance with your procedures, and corrections are made as needed.
Disposal of Waste and Toilet Paper
Your toilet facilities must be designed, located, and maintained to provide for the sanitary
disposal of waste and toilet paper. (21 CFR 112.129(b)(3)). Your toilet facilities should provide
for the sanitary collection of human waste, either into a secure sewage collection system that is
emptied as needed, or to a sewage transport system that moves it to an individual or municipal
treatment system. If your toilet or sewage transport system cannot accommodate toilet paper,
you should keep waste containers with self-closing lids immediately adjacent to the toilet, such
as receptacles with a sensor operated lid or other hands-free devices. You should monitor these
receptacles and empty them as necessary.
Hand-Washing Facilities
Hand-washing is a key control measure in minimizing the potential for transferring
contamination from human hands to covered produce and food contact surfaces (Ref. 100) (Ref.
132). All of the following requirements apply to hand-washing facilities:
•
•

•

You must provide your personnel with adequate, readily accessible hand-washing
facilities during growing activities that take place in a fully-enclosed building, and during
covered harvest, packing, or holding activities. (21 CFR 112.130(a)).
During growing activities that take place in a fully-enclosed building, and during covered
harvesting, packing, or holding activities, you must provide a hand-washing station in
sufficiently close proximity to toilet facilities to make it practical for persons who use the
toilet facility to wash their hands. (21 CFR 112.129(c)).
You also must make toilet and hand–washing facilities accessible to visitors. (21 CFR
112.33(b).

These standards apply to both fully plumbed, stationary hand-washing facilities and portable
units.
Adequate and Readily Accessible
You should consider personnel and visitor activities and traffic throughout your growing,
harvesting, packing, and holding areas to help you determine the appropriate number and
locations of hand-washing facilities to efficiently accommodate the typical numbers of
individuals accessing certain areas at the same time, such as at the beginning of work, or after a
break. You should evaluate your hand-washing facilities to determine whether they are easily
accessible for personnel working in areas where covered activities occur, including during all
harvesting activities and during growing activities that occur in fully-enclosed buildings.
122

Contains Nonbinding Recommendations
Draft-Not for Implementation
You should determine whether hand-washing facilities are located close to meal or break areas,
or at or near points of entry to areas where covered activities occur. Hand-washing facilities
should ideally be available immediately outside or inside the entrance to packing areas. Further,
additional hand-washing facilities should be placed near where personnel work (i.e., near a
sorting line), to ensure that personnel can easily access it if their hands become soiled or
contaminated (e.g., frequent contact with a trash can). The presence of hand-washing facilities at
these and similar locations could promote their use by personnel.
You should ensure that hand-washing facilities are in a location where they are accessible for
servicing, maintenance or disposal activities. Transport or other servicing vehicles or personnel
should have clear access to hand-washing facilities to ensure sanitary collection and disposal of
waste, including waste water, or other maintenance activities. For portable hand-washing
facilities, you could consider moving hand–washing facilities from areas near where covered
activities occur to a more remote location for waste water collection, cleaning, and servicing,
rather than have these functions performed when the portable hand-washing facility is near
covered activities. You should ensure that whomever performs these activities is aware of your
procedures.
You must ensure that your hand-washing facilities are designed, maintained and managed to
ensure sanitary conditions (See 21 CFR 112.130(a)). You should establish monitoring, servicing
and cleaning and sanitizing procedures and schedules for hand-washing facilities and perform
these activities at a frequency that ensures that they remain sanitary. You should consider the
frequency of use for your hand-washing facilities to assist you in determining your frequency for
cleaning and monitoring. Your procedures should include the frequency of these inspections, the
personnel involved, and conditions that should be reported to you, a supervisor, or other
responsible party. You should encourage personnel to report any observed deficiencies of the
hand-washing facilities to their supervisor or other responsible party to ensure hand-washing
facilities are continually maintained.
To assist with maintaining sanitary conditions, you could consider installing hand-washing
facility components that are automated or otherwise designed for hands-free use, such as faucets,
soap dispensers, and paper towels dispensers that can be activated by motion sensors or by foot
pedals. This could help prevent your personnel from re-contaminating their clean hands by
touching soiled faucet handles, or soap or paper towel dispensers.
Personnel to whom you assign the responsibility of maintaining hand-washing facilities, or who
are engaged in the supervision thereof, should understand your procedures. You should direct
the supervisors or other responsible parties, as applicable, to ensure that monitoring and other
activities are conducted in accordance with your procedures, and corrections are made as needed.
Supplies
Your hand-washing facilities must be supplied with soap (or other effective surfactant). (21 CFR
112.130 (b)(1)). A surfactant is a substance that helps to remove dirt from hands. You could not
use an antiseptic hand rub as a substitute for soap (or other surfactant) and water. (21 CFR
112.130(d)). However, you could provide hand sanitizers as an additional bactericidal measure

123

Contains Nonbinding Recommendations
Draft-Not for Implementation
for use after hand-washing with soap and water, and drying. See draft guidance in the section of
Chapter 3: Health and Hygiene (Subpart D) titled “Thorough Hand-washing”).
You must furnish your hand-washing facilities with running water that satisfies the requirements
of 21 CFR 112.44(a) for water used to wash hands (i.e., water must contain no detectable generic
E. coli per 100 mL of water). (21 CFR 112.130(b)(2)). You could, for example, obtain running
water from a fixed plumbing system or a portable unit that supplies and captures running water.
Containers used to transport or store water for hand-washing should be emptied and thoroughly
cleaned periodically. You should not reuse hand-washing water that has not been treated, nor
should you use communal, open containers of water for hand-washing.
You must furnish hand-washing facilities with adequate drying devices. (21 CFR
112.130(b)(3)). Examples of adequate drying devices include single-use disposable towels (e.g.,
paper towels), electric hand dryers, and cloth towels that are used only once and then laundered
(e.g., using your own procedures or use a sanitary towel service). Common or shared towels, or
towels intended for multiple uses before laundering are not adequate drying devices for this
purpose because repeated use of towels or use by multiple users can increase the potential for
contamination.
Disposal of Waste for Hand-Washing Facilities
You must provide for appropriate disposal of waste (e.g., waste water and used single-service
towels) associated with a hand-washing facility and take appropriate measures to prevent waste
water from a hand-washing facility from contaminating covered produce, food contact surfaces,
areas used for a covered activity, agricultural water sources, and agricultural water distribution
systems with known or reasonably foreseeable hazards. (21 CFR 112.130(c)).
•

Single-Service Towels and Other Solid Hand-Washing Waste

You should evaluate whether your solid hand-washing waste disposal systems contribute to
contamination of covered produce, food contact surfaces, areas used for a covered activity,
agricultural water sources, and agricultural water distribution systems. Containers used for solid
hand-washing waste (e.g., single-service towels) should be intact and free from damage, such as
cracks, or should be lined with an intact liner (e.g., garbage bag). You should develop
procedures for the frequency that these containers should be emptied (e.g., based on frequency of
use) so they do not serve as a source of contamination or pest attractant. These containers should
be covered to prevent the solid hand-washing waste from being transported (e.g., by wind, birds)
to areas where covered activities occur. You should cover waste containers in a way that also
helps prevent potential contamination of hands (e.g., foot-operated or remote sensor-operated
lids). Containers used for solid hand-washing waste disposal should be located as close as
practical to hand-washing facilities to maximize the likelihood that they will be used.
•

Liquid Hand-Washing Waste

You should evaluate whether your liquid hand-washing waste disposal systems contribute to
contamination of covered produce, food contact surfaces, areas used for covered activities, or
agricultural water sources or distribution systems. Your evaluation should include consideration
124

Contains Nonbinding Recommendations
Draft-Not for Implementation
of the surrounding area, such as topography and location of nearby water sources and covered
activities because of the potential for runoff of liquid waste from hand-washing stations. In
plumbed hand-washing facilities, liquid waste typically drains into a plumbed waste system.
Piping used to convey hand-washing liquid waste should be intact and free of leaks. See the
section of this chapter titled “Plumbing” for further draft guidance on waste water systems.
If you use portable hand-washing facilities, the liquid waste should be collected in a manner that
prevents contamination of covered produce, food contact surfaces, areas used for covered
activities, or agricultural water sources or distribution systems. For example, if a portable handwashing facility releases liquid waste onto the ground, the liquid could serve as a source of
contamination. Liquid hand-washing waste should be captured in a container that is intact and
free from leaks; the container should be covered when it is not in use or when it is collected for
disposal. You should empty these containers as necessary (e.g., once they are filled to a certain
point or at an established frequency based on use) and periodically clean them (e.g., at an
established frequency based on use). Liquid hand-washing waste containers should be emptied
in a way that minimizes the potential for spillage. If a third-party entity supplies and services
your portable hand-washing facilities, you should ensure that the liquid waste containers are
readily accessible to them and that they perform their activities in a manner that prevents
contamination. You should not locate portable hand-washing facilities near agricultural water
sources or in a location from which spilled liquid hand-washing waste could contaminate areas
associated with covered activities.
Sewage Systems
Sanitary disposal of human waste greatly reduces the likelihood that it will serve as a source of
contamination of covered produce, food contact surfaces, areas used for a covered activity, or
agricultural water sources or distribution systems (Ref. 25) (Ref. 68). Systems used to handle
human waste include municipal sewage systems, individual septic systems, self-contained units,
which could be portable, and any associated plumbing.
Use and Maintenance
You must dispose of sewage into an adequate sewage or septic system or through other adequate
means. (21 CFR 112.131(a)). You must maintain sewage and septic systems in a manner that
prevents contamination of covered produce, food contact surfaces, areas used for a covered
activity, agricultural water sources, and agricultural water distribution systems with known or
reasonably foreseeable hazards. (21 CFR 112.131(b)). You should evaluate your sewage and
associated plumbing systems (i.e., collection, containment, transport) based on these
requirements. Generally, sewage and septic systems in the U.S. are approved by local health
authorities when installed, providing a level of assurance that their design is appropriate (e.g., the
volume of water and organic material, including fecal material). However, these systems can
degrade over time (e.g., leaks, bypasses, damage, incomplete treatments), presenting the risk for
contamination of surrounding soils and waters (Ref. 45) (Ref. 42). Further, for systems that treat
the sewage (e.g., septic systems), if your input volume or other characteristics exceed the design
capacity, the system could not properly treat the sewage, potentially allowing pathogens to
survive in the effluent.

125

Contains Nonbinding Recommendations
Draft-Not for Implementation
As part of your maintenance activities, you should periodically inspect your sewage systems,
including those used for plumbed (e.g., sewer and septic systems) and non-plumbed (e.g.,
portable toilets, outhouses) toilet facilities. You should have procedures for the frequency of
these inspections, the personnel involved, and conditions that should be reported to you, a
supervisor, or other responsible party.
If you use a septic system, the tank should be properly sealed, in good working order, and free
from damage. The inlet and outlet plumbing should be in good working order and free from
damage, and the drain field should be properly functioning, with no visible leakage at the
surface. If you use a septic system, you should have it pumped with sufficient frequency to
prevent excess accumulation of solid human waste, which can result in premature septic system
or drain field failure (Ref. 41) (Ref. 106).
For portable toilet facilities, the waste retention tank should be structurally sound, not leak, and
be constructed to prevent contamination and attraction of flies and other pests. The tanks should
remain closed to minimize the potential for contamination. You should store these tanks in a
way that protects them from damage that could result in leakage of human waste. Storage
containers should be accessible to facilitate collection and transport of sewage and liquid waste
or other maintenance and servicing activities. You should dispose of human waste from these
tanks periodically (e.g., at an established frequency based on use) to prevent overflow. You
should ensure that the collection and disposal of human waste from your portable toilet facilities
or outhouses is done in a manner that prevents spills.
Response to Leaks and Significant Events
You must manage and dispose of leakages or spills of human waste in a manner that prevents
contamination of covered produce, and prevents or minimizes contamination of food contact
surfaces, areas used for a covered activity, agricultural water sources, or agricultural water
distribution systems. (21 CFR 112.131(c)).
In the event of a sewage spill or leak, you should contact your local public health or waste
management authorities for assistance in complying with their regulations for sewage disposal.
Management of a human waste spill or leak could include:
•
•
•
•
•
•
•

Containing the spill or leak;
Preventing your personnel from entering the affected area;
Removing and disposing of the spill or leakage contents;
Disposing of any contaminated covered produce;
Cleaning and sanitizing any contaminated food contact surfaces;
Repairing or replacing any faulty sewage system components; and
Evaluating any potential impacts to growing area soil, food contact surfaces, covered
activity areas, or agricultural water sources or distribution systems.

Furthermore, if you know or have reason to believe that there is a sewer or septic system failure
(e.g., soggy patches of land around your septic tank or drain field, slow draining sinks or drains,
sewage odors, gurgling noises from the plumbing drain lines, or effluent backup coming from
drains, sinks or toilets) (Ref. 41) (Ref. 44), you should immediately cease any water use that
126

Contains Nonbinding Recommendations
Draft-Not for Implementation
drains or transmits waste water into the affected sewage or septic system. You should also
determine the cause of the leak or spill and make any necessary repairs. For example, if you find
that the sewage system failure is the result of a sewer line that is burst, cracked, or penetrated,
such as with tree roots, you should repair or replace the affected section. You should verify that
any actions corrected the problem before resuming use of the sewage or septic system. In some
instances, this might include having the system professionally inspected by a private firm or your
local health authority.
Sewage spills can occur in indoor facilities. For example, if a toilet overflows onto the floor of a
toilet facility that is accessed by personnel who work in areas where covered produce is exposed,
you should immediately prevent access to the affected area until the spill can be removed and the
area thoroughly cleaned and sanitized. If your personnel access the area before it is cleaned, you
should visually assess the potential that covered produce or food contact surfaces in adjoining
areas have become contaminated. You should ensure that your personnel and supervisors or
other responsible parties understand your procedures for responding to a leak or spill of sewage.
You should direct your supervisors or other responsible parties, as applicable, to ensure that
actions taken to manage and dispose of leakages or spills of sewage are conducted in accordance
with your procedures and corrections are made as needed.
In addition, after a significant event, such as flooding or an earthquake, that could negatively
impact your sewage or septic system, you must take appropriate steps to ensure that sewage and
septic systems continue to operate in a manner that does not contaminate covered produce, food
contact surfaces, areas used for a covered activity, agricultural water sources, or agricultural
water distribution systems. (21 CFR 112.131(d)). After such an event, you should inspect your
entire system to the extent that it is accessible to identify and correct any defects with the system.
For example, you could find that an earthquake has damaged the intake or output baffles in your
septic tanks; you should promptly repair these defects to prevent sewage, incomplete treatments,
and premature drain field failure. In another example, if you find that your septic system’s drain
field is failing due to flooding, you should wait for water levels to recede before resuming use of
the system and evaluate the potential for the contamination of covered produce, food contact
surfaces, areas used for a covered activity, agricultural water sources, or agricultural water
distribution systems.
When your inspection after a significant event indicates defects in your system, you should also
consider whether you can continue to perform growing, harvesting, packing, and holding
activities in a manner that complies with the Produce Safety Rule. You should consider taking
actions such as providing temporary, portable toilet and hand-washing facilities, and you should
determine whether such actions would be adequate to prevent contamination (See 21 CFR
112.131(a)). There could be circumstances during which it is unsafe to continue growing,
harvesting, packing, and holding covered produce, until the sewage system can be fully repaired
(e.g., if water from your production activities and cleaning activities is directed to the sewage
system).
Trash, Litter, and Waste
For the control and disposal of trash, litter, and waste in areas used for covered activities, you
must:
127

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

•

Convey, store, and dispose of trash, litter, and waste to:
o Minimize its potential to attract or harbor pests (21 CFR 112.132(a)(1)); and
o Protect against contamination of covered produce, food contact surfaces, areas
used for a covered activity, agricultural water sources, and agricultural water
distribution systems with known or reasonably foreseeable hazards (21 CFR
112.132(a)(2)).
Adequately operate systems for waste treatment and disposal so that they do not
constitute a potential source of contamination in areas used for a covered activity. (21
CFR 112.132(b)).

You should evaluate your waste management system for compliance with these requirements,
including:
•
•
•

Type and location of waste containers for collection or storage;
Frequency of waste collection and disposal; and
Maintenance of waste collection and storage areas.

Personnel to whom you assign the responsibility of conveying, storing and disposing of trash,
litter and waste, or who are engaged in the supervision thereof, should understand your
procedures. You should direct the supervisors or other responsible parties, as applicable, to
ensure that activities are conducted in accordance with your procedures, and corrections are
made as needed.
You have the flexibility to select waste containers that you determine to be appropriate for your
waste collection and storage activities. However, you should ensure that waste containers are not
prone to spills, leaks, or overflow. Waste containers should be covered with tight-fitting lids
when not in use, especially in outdoor areas or partially-enclosed buildings, to minimize the
attraction of pests. You should cover waste containers in a way that also helps prevent potential
contamination of hands (e.g., foot-operated or remote sensor-operated lids).
Waste containers should be readily available in areas where waste is typically generated (such as
near sorting areas and personnel break areas) and positioned so that they are not likely to be
overturned. Their location should minimize the need for personnel who contact covered produce
or food contact surfaces to have to adjust or relocate the containers during covered activities.
Waste containers should accommodate the typical volumes of waste generated.
You should establish an appropriate frequency for transferring waste from your waste collection
containers to waste storage containers (e.g., dumpsters). In establishing the frequency for
transfer, you should consider the volume of waste collected and the nature of the waste. Waste
removal should be more frequent for waste material that is likely to serve as a source of
contamination or attract pests. For example, unlike some dry waste (e.g., damaged boxes or
overwrap), discarded produce in areas where covered activities occur could be more likely to
attract pests and contribute organic materials that promote bacterial growth, so waste collection
in these areas should be more frequent.
You should locate your waste storage containers (e.g., dumpsters) away from areas where
covered produce or food contact surfaces are exposed. You should consider the potential for
128

Contains Nonbinding Recommendations
Draft-Not for Implementation
runoff from these locations to areas you use for covered produce, food contact surfaces, areas
used for a covered activity, agricultural water sources, and agricultural water distribution
systems. You could, for example, locate waste storage downhill from these areas or use berms
or other grading to prevent runoff. Your waste storage containers should always remain closed
when not in immediate use. Waste storage containers should be emptied in a manner and
frequency that prevents waste from spilling or leaking.
You should establish periodic cleaning, sanitizing, and maintenance schedules for your waste
collection and storage containers, and equipment used to transport these items (e.g., forklifts) to
minimize the potential of contamination. Waste containers and equipment used to transport
these items should be maintained, free from damage that facilitates leaks, and replaced as
necessary. Equipment used for waste disposal (e.g., conveyers) should be separated from
covered produce and food contact surfaces and positioned in a way that minimizes the potential
for their contamination.
Plumbing
Plumbing must be of an adequate size and design and be adequately installed and maintained to:
•
•
•
•

Avoid being a source of contamination to covered produce, food contact surfaces, areas
used for a covered activity, or agricultural water sources. (21 CFR 112.133(c));
Distribute water under pressure as needed, in sufficient quantities, in all areas where used
for covered activities, for sanitary operations, hand-washing, or toilet facilities. (21 CFR
112.133(a));
Properly convey sewage and liquid disposable waste. (21 CFR 112.133(b)); and
Not allow backflow from, or cross-connection between, piping systems that discharge
waste water or sewage and piping systems that carry water used for a covered activity, for
sanitary operations, or for use in hand-washing facilities. (21 CFR 112.133(d)).

Your plumbing system includes water lines and structures (e.g., faucets, toilets, pipes, collection
and containment structures), and sewage lines and structures (e.g., pipes, collection and
containment structures). You should evaluate the adequacy of your plumbing systems
considering such factors as volume of water and frequency of use. You should periodically
inspect your plumbing system and identify any conditions that could result in it becoming a
source of contamination. Your procedures should include the frequency of these inspections, the
personnel involved, and conditions that should be reported to you, a supervisor, or other
responsible party. If you observe the potential for contamination, you should take appropriate
measures to prevent the plumbing from becoming a source of contamination, as soon as possible.
For example, you could remove dead-end piping or periodically flush these lines to remove any
residue or other material.
Inadequate water pressure and volume could impact your ability to perform your operations in a
sanitary manner. For example, low water pressure could compromise your ability to properly
clean your food contact surfaces or to provide water to multiple hand-washing facilities at the
same time.

129

Contains Nonbinding Recommendations
Draft-Not for Implementation
Plumbing for sewage and liquid disposable waste should be intact and free from leaks to prevent
contamination of surrounding areas (e.g., packing area floors, growing area soil, agricultural
water sources and distribution systems, such as irrigation systems). For additional draft guidance
see the section of this chapter titled “Sewage Systems.”
A cross-connection is a connection between a water source or distribution pipe (e.g., drinking
water, water used for hand-washing, water used for cooling covered produce) and a liquid waste
pipe (e.g., sink drain, sewage line, floor drain line). Unless it is protected by a backflow
prevention device, a cross-connection can result in backflow, the undesirable reversal of the flow
against the normal waterline pressure (e.g., from a sewage line to the water line supplying a
hand-washing station). You should equip all water supply piping with backflow prevention
devices to prevent contamination from cross-connections and backflow.
Hoses should be used in a manner that prevents back-flow. Hoses that are connected to water
lines under pressure could become sources of contamination to the water supply if an
unintentional, temporary cross-connection is created. For example, if you leave an open-ended
hose on the floor in pooled water or submerged in water, backflow can occur if a pressure
differential develops, reversing the flow of water in the hose. This backflow could result in
contamination of the water supply. Hoses should be stored off the floor on a designated holder.
Drainage systems involving water contact with covered produce, such as from flumes or dump
tanks, should flow into a floor drain with an air gap or with a backflow or back siphonage
prevention device to prevent contamination of the flume system or dump tank if a backup occurs
in the drainage system.

4. Records
You must establish and keep documentation of the date and method of cleaning and sanitizing of
equipment subject to subpart L used in (1) growing operations for sprouts; and (2) covered
harvesting, packing, or holding activities. (21 CFR 112.140). Examples of such equipment and
tools include harvesting tools, knives, implements, mechanical harvesters, waxing machinery,
cooling equipment (including hydrocoolers), grading belts, sizing equipment, palletizing
equipment, and equipment used to store or convey harvested covered produce (such as
containers, bins, food-packing material, dump tanks, flumes, and vehicles or other equipment
used for transport that are intended to, or likely to, contact covered produce). An example of
such a record would be a cleaning and sanitizing log for packing equipment that documents the
date that cleaning or sanitizing was performed, and the method of cleaning or sanitizing (e.g.,
“manual scrub with detergent and hot water”). The record should include the concentration of
cleaning or sanitizing solutions (e.g., “sanitized with 200 ppm chlorine spray”). You could, for
example, develop records for groups of equipment that are cleaned and sanitized in the same way
with the same cleaning and sanitizing solutions.
Chapter 8: Records (Subpart O) provides draft guidance on the general records requirements that
are applicable to these records.

130

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 8:
Records (Subpart O)
This chapter provides draft guidance on the requirements of subpart O–Records. Records are
needed to keep track of measures directed at minimizing the risk of known or reasonably
foreseeable hazards, to identify a pattern of problems that increase the risk of such hazards, and
to facilitate verification and compliance with regulatory standards. The records requirements
will help you to comply with the requirements of the Produce Safety Rule and document, and
FDA to determine, your compliance. Additionally, records provide you, and FDA, with a view
of the performance of your preventive measures over time.
In this chapter, we provide draft guidance on the requirements of subpart O that apply to all
required records under the Produce Safety Rule (21 CFR Part 112). The specific records that
your farm must keep depend, in part, on the requirements of the Produce Safety Rule that apply
to your farm. The requirements for specific records are listed in the applicable sections of the
Produce Safety Rule: subparts A, B, C, E, F, L, and M (i.e., 21 CFR 112.2(b)(4), 112.7,
112.12(c), 112.30, 112.60, 112.140, and 112.150). (See also the subsection of this chapter titled
“Specific Records Requirements”). You should consult the chapters of this draft guidance
related to subparts A, C, F, and L to ensure that you establish and maintain the specific records
that those subparts require; subparts D, I, K, N, P, Q, and R do not require specific records. We
separately address specific records requirements for subpart M–Sprouts. We also intend to
separately provide draft guidance for the requirements of subparts B–General Requirements
(specifically, Alternatives) and E–Agricultural Water; and on specific records for these subparts.
Subpart O describes the requirements for establishing and maintaining records, including:
general requirements; records storage; use of existing records; records retention; records format;
and records disclosure. With a few exceptions, these requirements apply to all records the
Produce Safety Rule requires.
Personnel to whom you assign the responsibility of developing, creating, completing or
reviewing records should understand your procedures. You should direct supervisors or
responsible parties, as applicable, to ensure that records are created and reviewed in accordance
with your procedures and corrections are made as needed. You could access templates for
records from sources such as academia, extension services, and industry associations to assist
you in creating a consistent approach.

1. General Requirements for all Records
Except as otherwise specified, the requirements of subpart O apply to all records that are
required under the Produce Safety Rule. All required records must include, as applicable and
unless otherwise specified:
•
•

The name and location of your farm (21 CFR 112.161(a)(1)(i));
Actual values and observations obtained during monitoring (21 CFR
112.161(a)(1)(ii));

131

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

•
•

An adequate description (such as the commodity name, or the specific variety or
brand name of a commodity, and, when available, any lot number or other
identifier) of covered produce applicable to the record (21 CFR
112.161(a)(1)(iii));
The location of a growing area or other area (for example, a specific packing
shed) applicable to the record (21 CFR 112.161(a)(1)(iv)); and
The date and time of the activity documented (21 CFR 112.161(a)(1)(v)).

Required records must also:
•
•
•

Be created at the time an activity is performed or observed (21 CFR
112.161(a)(2));
Be accurate, legible, and indelible (21 CFR 112.161(a)(3)); and
Be dated, and signed or initialed by the person who performed the activity
documented (21 CFR 112.161(a)(4)).

Farm Name and Location
Your required records must include, as applicable, the name and location of your farm. (21 CFR
112.161(a)(1)(i)). This requirement ensures that your records are linked to your farm. You
should use the postal address or physical location (such as latitude or longitude) of the farm.
You may choose to use documents pre-printed with your farm name and location to ensure that
this information is captured on each of your records. If your records include written information
obtained from a third party (e.g., a report of analysis from a contract laboratory) and the
information provided by the third party does not include certain required information (e.g., a
customer number instead of your farm’s name and location), you can fulfill this requirement by
supplementing the record with the additional required information, or including it on a new,
attached record. Additional draft guidance is provided in the section of this chapter titled “Use
of Existing Records.”
Location of Growing or Activity Area
Your required records must include, as applicable, the location of a growing area or other area
applicable to the record. (21 CFR 112.161(a)(1)(iv). This requirement ensures that your records
are linked to the specific growing areas, packing areas, or other areas of your farm that are
relevant to the record. Your personnel might create required records relative to several different
areas on your farm. You should therefore establish a system to accurately document the location
applicable to the record, such as by using specific identifiers (e.g., field names or numbers;
building names or numbers; or geographical markers) for the various areas on your farm. For
example, if a farm grows carrots in three separate fields and the records do not provide a specific
identifier (e.g., name or number) for each field, the record would not be sufficiently specific to
link the record to a specific field. You should determine whether areas of your farm have
existing specific location identifiers that you can use for your records or whether you need to
create new identifiers. If you already have farm maps with specific field, orchard, grove, or
vineyard numbers, or other specific identifiers, for each site, you can record those identifiers on
your records. You may also choose to use street addresses or specific coordinates using a GPS
or other mapping system.
132

Contains Nonbinding Recommendations
Draft-Not for Implementation
Adequate Description of Covered Produce
Your required records must include an adequate description of covered produce applicable to the
record. (21 CFR 112.161(a)(1)(iii)). Descriptions should include the relevant commodity name,
or the variety name or brand name, and any lot number or code that you use to identify the
covered produce. For example, if your farm grows different varieties of apples–one variety in
each of three orchards–then your records for each orchard should, as appropriate, describe the
covered produce grown in the relevant orchard: “apples, Fuji;” “apples, Granny Smith;” or
“apples, Golden Delicious.”
Actual Values and Observations
Your required records must include, as applicable, actual values and observations obtained
during monitoring. (21 CFR 112.161(a)(1)(ii)). The records should include accurate values or
observations from an instrument or a visual assessment by personnel, as applicable (e.g., a
temperature reading of 96.2°F from a thermometer, or a pH meter reading of 4.20). Recording
actual values and observations during monitoring is necessary to produce an accurate record.
Records stating that monitoring measurements are “satisfactory” or “unsatisfactory,” without
recording the actual times and observations (e.g., temperatures and turnings in treating biological
soil amendments of animal origin) are vague and subject to varying interpretations and, thus, will
not ensure that required measures have been taken or standards have been met. In addition, it is
not possible to discern a trend without actual measurement values.
Furthermore, recordings of instrument readings must reflect the actual value displayed by the
instrument, without rounding or generalization. (See 21 CFR 112.161(a)(1)(ii)). For example, if
personnel conduct a pH measurement of composting manure and the reading is 6.56, the
recorded value must be stated as “6.56,” rather than “pass” or “OK,” or rather than being
rounded to “7.0” or written as “> 6” (greater than 6.0). (See 21 CFR 112.161(a)(1)(ii)).
Created when Activity is Performed or Observed
As applicable, your required records must be created at the time an activity is performed or
observed. (21 CFR 112.161(a)(2)). This requirement ensures that the accuracy of recorded
information is not impacted by human error, such as lapses in memory. If an individual does not
create the record at the time an activity is performed or observed, they could create an inaccurate
record by forgetting the exact value observed, confusing values for multiple observations, or
forgetting to create the record. For example, if a worker is responsible for recording sanitizing
activities that occur in a packing area, the worker should record each activity or observation,
such as the pieces of equipment sanitized and the compounds and concentrations of treatments
used, as it is performed.
Date and Time
Your required records must include, as applicable, the date and time of the activity documented.
(21 CFR 112.161(a)(1)(v)). You should establish a procedure for personnel to use when
recording dates to ensure consistency and clarity. For example, you might set a procedure that
personnel should record all dates in the format of MM-DD-YYYY. Personnel should record
133

Contains Nonbinding Recommendations
Draft-Not for Implementation
times without rounding or generalization. For example, if personnel take a measurement at
1:03pm, they should record that time, not 1:00pm or 1:05pm.
Accurate, Legible, and Indelible
Your required records must be accurate, legible, and indelible. (21 CFR 112.161(a)(3)).
Legibility is particularly important for records involving handwritten entries. Indelibility is
important to ensure that the original content has not been altered; therefore, records should not be
erasable. For example, an erasable white-board is not indelible. If mistakes are made on a
required record, your personnel should correct the original marking in a way that allows both the
original content and the updated content to be read. In other words, you should not mark over
the original content in a way that prevents a person from reading the original content. For
example, if an incorrect value of “6.0” is written in permanent ink, the person who recorded that
value should draw a single line through the “6.0,” add the accurate value of “6.1,” and write their
initials and the date nearby. For specific records listed in 21 CFR 112.161(b), a supervisor or
responsible party reviewing records, when required by 21 CFR 112.161(b), should assess
whether the record is legible.
Dated, and Signed or Initialed by the Person Who Performed the Activity
The person who performed the activity documented must date, and sign or initial the record. (21
CFR 112.161(a)(4)). This ensures that you can identify the individual who performed the
activity recorded as well as the date the record was completed. While this provision allows for
the use of initials instead of a signature, there could be circumstances in which initials alone
could be confusing. For example, if you have multiple workers with the same initials (e.g., John
Dab, Jane Dell, and Jennifer Doe), your procedures should direct those personnel to sign their
full name or provide some additional identifier (e.g., “JD1” or “J. Dab” or “JWD”) instead of
using only their first and last initials.
Review by a Supervisor or Responsible Party
A supervisor or responsible party must review, date, and sign the following records within a
reasonable time after those records are created:
•
•

As applicable, records demonstrating eligibility for a qualified exemption under 21 CFR
112.7(b);
As applicable, documentation that process controls were achieved for a treated biological
soil amendment of animal origin you produce for you own covered farm(s), as required
under 21 CFR 112.60(b)(2);

134

Contains Nonbinding Recommendations
Draft-Not for Implementation
•

Documentation of cleaning and sanitizing of equipment under 21 CFR 112.140(b)(1) and
(2). (21 CFR 112.161(b)). 11

When reviewing these records, the supervisor or responsible party should determine whether:
•
•

•

The records are complete, including whether personnel recorded their observations at the
appropriate frequency for a given activity;
If any problems were recorded, those problems were addressed with appropriate
corrective measures (for example, if a supervisor reviews a composting record and
notices that a given temperature reading was below the necessary temperature for an
effective treatment, the supervisor should confirm that the compost was either retreated
or handled as untreated); and
Any necessary corrective measures are taken in a timely manner. For example, if records
indicate the need for a corrective measure to prevent distribution of an adulterated
product, then a supervisor or other responsible party should confirm that the appropriate
measure was performed.

You should also review records to identify trends in recorded values or observations so that you
can adjust before it is necessary to take corrective measures. You should review records for any
unexpected results. For example, if a supervisor reviews a record of a sanitizer pH value, which
they expect to be pH 6-7, and the recorded value is 4.2, the supervisor should follow-up with the
worker who made the recording to determine whether there was a malfunction with the
monitoring instrument, a difficulty by the worker in reading the instrument, a recording error
(i.e., the record is not accurate), or some other problem.
The supervisor or responsible party review must take place within a reasonable time after the
records were created. (See 21 CFR 112.161(b)). In most instances, we believe that an
appropriate time period for a supervisor or responsible party to review records is approximately
one week after the record is created. In some cases, you could find that a shorter or longer
timeframe is appropriate. You should adopt procedures regarding records review timeframes to
ensure that supervisors and responsible parties consistently perform reviews within a reasonable
timeframe to allow for any necessary follow-up actions. For example, a reasonable timeframe
should generally allow for covered produce or other items relevant to the record (such as
equipment or biological soil amendments of animal origin) to be available so that you can take
follow-up actions if needed.
A detailed records review could become tedious, particularly when the various records include
similar information. You should ensure that supervisors and responsible parties review records
at a time when they can focus on the records.
When the owner or supervisor is both the person who performed the activity and the responsible
party who reviews the record, the requirements in both 21 CFR 112.161(a)(4) and 112.161(b) are
11

The regulation at 21 CFR 112.161(b) also requires that a supervisor or responsible party review, date, and sign
records required by 21 CFR 112.50(b)(2), (4), and (6), and 21 CFR 112.150(b)(1), (4), and (6), which are not
addressed in this draft guidance.

135

Contains Nonbinding Recommendations
Draft-Not for Implementation
satisfied when that person signs and dates the record. In this situation, the owner or responsible
party should perform a thorough record review to evaluate the information in the record after the
record includes all information required by the Produce Safety Rule (e.g., after that person
records information such as the actual values and observations obtained during monitoring).

2. Records Storage
You have the flexibility to store your records in a way that allows you to easily access them as
necessary and to organize them consistent with your operating procedures. You should evaluate
how frequently you need to access your records and how you use them on your farm, and then
develop a records management strategy that best fits your needs. All records required under the
Produce Safety Rule must be readily available and accessible to FDA. (21 CFR 112.166).
Required records must be stored either on the farm (i.e., “onsite”) or away from the farm (i.e.,
“offsite”). (21 CFR 112.162). Electronic records are considered onsite at your farm if they are
accessible from an onsite location at your farm. (21 CFR 112.162(b)). If you have multiple
growing sites for your farm, you could keep records at each site or consolidate all records from
each growing site at a single site on your farm. For example, if a farm has three growing sites
and sometimes uses seasonally-rented fields, the farm could choose to store all its records at the
farm’s main office, even if some of the records were completed at the three growing sites and the
seasonally-rented fields. As another example, the farm could store certain records for each
growing site at that growing site while other records are stored at the farm’s main office.
Offsite storage of records is permitted if such records can be retrieved and provided onsite within
24 hours of request for official review. (21 CFR 112.162(a)). For example, your farm could
generate some records that you need to easily access for a period of time, such as for one month
or for a full growing season. You could choose to transfer the records to a central storage
location, which is not part of the farm, for longer-term storage after that initial time period has
ended. If those records are in an offsite storage location, they must be able to be retrieved and
provided onsite within 24 hours of a request for official review. (21 CFR 112.162(a)).

3. Use of Existing Records
You may use existing records and information (e.g., documents or information that you have
already developed and maintained during the normal course of your farm’s business, including
records that are kept to comply with other Federal, State, or local regulations, or for any other
reason) to comply with subpart O if those records contain all of the required information and
satisfy the requirements of the Produce Safety Rule. (See 21 CFR 112.163(a)). It is not
necessary for you to keep all of the required information in only one set of records, nor do you
need to duplicate existing records, provided that, taken together, your records satisfy all of the
applicable requirements of the Produce Safety Rule. (See 21 CFR 112.163). If existing records
contain only some of the required information, you may keep additional information required for
compliance with the Produce Safety Rule either separately or in combination with the existing
records. (21 CFR 112.163(b)). If you maintain records required by another entity, and those
records contain some of the information required by the Produce Safety Rule, you are not
required to duplicate the overlapping components. For example, your records must contain, as
applicable, information such as the name and location of your farm (21 CFR 112.161(a)(1)(i)).
136

Contains Nonbinding Recommendations
Draft-Not for Implementation
If your records include written information obtained from a third party (e.g., a report of analysis
from a contract laboratory) and the information provided by the third party does not include your
farm’s name and location, you can fulfill this requirement by keeping your farm’s name and
location recorded either separately or combined with the existing records.
As another example, if you maintain records of your annual gross food sales as part of your
documentation (in addition to your annual review record) to demonstrate that your farm meets
the criteria for a qualified exemption from the Produce Safety Rule (21 CFR 112.7(b)), you
could find that both your invoices and other financial records kept in the normal course of
business provide the necessary information. In this case, you would only need to keep one of
these types of records (not both) to satisfy the requirement for documentation that your farm
meets the criteria for the exemption (in addition to your annual review record), as long as the
records you keep include all of the necessary information.

4. Records Retention
You must keep records required by the Produce Safety Rule for at least 2 years past the date the
record was created. (21 CFR 112.164(a)(1)). If you have a record with multiple entries, you
should keep the record for 2 years past the date of the last recorded entry. This could include
records such as: training records required by 21 CFR 112.30(b); the process used to treat a
biological soil amendment of animal origin that you produce, as required by 21 CFR
112.60(b)(2); and the date and method of cleaning and sanitizing of equipment, as required by 21
CFR 112.140(b)(2).
You must also keep records that relate to the general adequacy of your equipment or processes,
or records that relate to analyses, sampling, or action plans being used by your farm, including
the results of scientific studies, tests, and evaluations, for at least 2 years after the use of such
equipment or processes, or records related to analyses, sampling, or action plans, is discontinued.
(21 CFR 112.164(b)). Examples of such records include records that contain annual written
assurances from your customers regarding produce that receives commercial processing (21 CFR
112.2(b)(4)), if you keep such records because you rely on the exemption in 21 CFR 112.2. 12
If you rely on the qualified exemption in 21 CFR 112.5, you must keep records supporting your
qualified exemption, in accordance with 21 CFR 112.5 and 112.7, as long as necessary to
support your farm’s status during the applicable year. (21 CFR 112.164(a)(2)). This period
could be as long as four years (i.e., the three previous years of financial records upon which you
determined your eligibility for a qualified exemption and the current year for which the
determination applies).

5. Records Format
You have the flexibility to maintain your records as original records, true copies, or electronic
records. (21 CFR 112.165). “True copies” include, for example, photocopies, pictures, scanned
12

As noted above, we have stated that we intend to exercise enforcement discretion related to the written assurances
associated with the commercial processing exemption.

137

Contains Nonbinding Recommendations
Draft-Not for Implementation
copies, microfilm, microfiche, or any other accurate reproduction of the original record. True
copies of records should be of sufficient quality to reveal whether the original record was
changed in a manner that obscured an original entry (e.g., by using liquid correction fluid).
“Electronic records” are subject to the same requirements as paper records under the Produce
Safety Rule. You could use paper or electronic records, or a combination of the two, to satisfy
the requirements of the Produce Safety Rule.

6. Records Disclosure
Records obtained by FDA in accordance with the Produce Safety Rule are subject to the
disclosure requirements under 21 CFR part 20. (21 CFR 112.167). This includes certain
protection for confidential commercial information and trade secrets (See, e.g., 21 CFR 20.61).
Our general policies, procedures, and practices relating to the protection of such information also
apply to information received under the Produce Safety Rule.

7. Specific Records Requirements
As noted above, subpart O describes how you must establish and maintain records the Produce
Safety Rule requires. You should refer to the following specific areas of the Produce Safety
Rule and the relevant chapters of this draft guidance to determine what specific records you are
required to keep that, with a few exceptions, are subject to the requirements of subpart O:
•

•
•
•

Subpart A–General Provisions:
o Produce eligible for exemption based on receipt of commercial processing that
adequately reduces the presence of microorganisms of public health significance
(21 CFR 112.2(b)(4));
o Qualified Exemption (21 CFR 112.7);
Subpart C–Personnel Qualifications and Training;
Subpart F–Biological Soil Amendments of Animal Origin and Human Waste; and
Subpart L–Equipment, Tools, Buildings, and Sanitation.

These specific records represent minimum standards; you could keep additional records related
to practices on your farm to support minimizing the risk of contaminating covered produce.

138

Contains Nonbinding Recommendations
Draft-Not for Implementation

Chapter 9:
Variances (Subpart P)
Subpart P of the Produce Safety Rule provides that a State, Federally-recognized tribe (“tribe”),
or foreign country from which food is imported into the United States (“foreign country”) may
request a variance from one or more requirements of subparts A through O of the rule, where the
State, tribe, or foreign country determines that:
•
•

The variance is necessary in light of local growing conditions; and
The procedures, processes, and practices to be followed under the variance are
reasonably likely to ensure that the produce is not adulterated under section 402 of the
FD&C Act and to provide the same level of public health protection as the requirements
of this part. (21 CFR 112.171).

This chapter provides draft guidance on the requirements of subpart PVariances, and the
procedures to request a variance. In addition, this chapter provides draft guidance on how FDA
intends to evaluate requests for a variance.

1. Entities Eligible to Submit a Variance Request
The request for a variance must come from the competent authority (i.e., the regulatory authority
for food safety) for a State, tribe, or foreign country. (See 21 CFR 112.171 and 112.172).
Entities that are not the regulatory authority for food safety, such as a state commodity
commission, are not eligible to request a variance. However, as discussed below, such groups
(and others) may assist the competent authority in developing supporting information for the
variance request.

2. Grounds for a Variance
A competent authority (“CA”) may request a variance from one or more of the provisions of
subparts A through O of the Produce Safety Rule. (21 CFR 112.182). Examples of some of the
permissible types of variances are provided in 21 CFR 112.182.
To request a variance, a CA must submit a petition under 21 CFR 10.30. (21 CFR 112.172). In
addition to the requirements of 21 CFR 10.30, the Statement of Grounds of the CA’s petition
requesting a variance must provide a statement that the CA determined that:
•
•
•

The variance is necessary in light of local growing conditions;
The procedures, processes, and practices to be followed under the variance are reasonably
likely to ensure that the produce is not adulterated under section 402 of the FD&C Act; and
The procedures, processes, and practices to be followed under the variance are reasonably
likely to provide the same level of public health protection as the relevant requirements of the
Produce Safety Rule. (21 CFR 112.173(a)).

The CA also must describe with particularity:
139

Contains Nonbinding Recommendations
Draft-Not for Implementation
•
•
•

The variance requested;
The persons to whom the variance would apply; and
The provision(s) of the Produce Safety Rule to which the variance would apply. (21 CFR
112.173(b)).

Further, the CA must present information demonstrating:
•
•

That the procedures, processes, and practices to be followed under the variance are
reasonably likely to ensure that the covered produce is not adulterated under section 402 of
the FD&C Act; and
That the procedures, processes, and practices to be followed under the variance are
reasonably likely to provide the same level of public health protection as the requirements of
the Produce Safety Rule. (21 CFR 112.173(c)).

In evaluating whether a variance is “necessary in light of local growing conditions,” the CA
might consider factors such as climate, soil, and geographical and environmental conditions in its
particular region. If particular controls (such as regional-specific practices, processes, or
procedures) or oversight (such as regional produce marketing programs) are used, the nature of
the oversight established could also be relevant to the CA’s request.
The petition’s Statement of Grounds must describe with particularity the variance requested. (21
CFR 112.173(b)). It must include the persons to whom the variance would apply and the
provision(s) of the Produce Safety Rule to which the variance would apply. (21 CFR 112.73(b)).
Specifically, this includes what farms would be covered by the variance; the measures that farms
covered by the variance would follow; and the provisions of the Produce Safety Rule for which
those measures would be substituted. The CA must also indicate the persons to which it requests
that the variance apply. (21 CFR 112.173(b)). For example, the requested variance might apply
to all persons in the CA’s jurisdiction, or might be limited to a specific group in the jurisdiction.
If the CA’s proposed approach is based, at least in part, on climate, soil, or geographical or
environmental conditions of a particular region within the CA’s jurisdiction, the petition should
describe those conditions and the boundaries of the specific region involved.

3. Information to Support a Request for a Variance
The Statement of Grounds in a petition requesting a variance must present information
demonstrating that the procedures, processes, and practices to be followed under the variance are
reasonably likely to ensure that the produce is not adulterated under section 402 of the FD&C
Act and to provide the same level of public health protection as the requirements of the Produce
Safety Rule. (21 CFR 112.173(c)).
A CA should include relevant and scientifically-valid information or materials specific to the
covered produce or covered activity to support the request for a variance from corresponding
requirements established in the Produce Safety Rule, in accordance with the requirements of 21
CFR 112.173(c). It is likely that a CA will use several resources to gather the information
necessary to support and describe its request for a variance. A CA could develop the information
itself, obtain it from scientific literature or a third party (such as a trade association or
commodity board), or use some combination of resources to collect the necessary information.
140

Contains Nonbinding Recommendations
Draft-Not for Implementation
A CA could, for example, present in its petition information that came from an individual farm
or group of farms, an importer or exporter, a trade or other industry association, academia, a
private food safety entity, a consultant, or another stakeholder. The scientific support for a
variance could be developed, for example, through a broad effort involving farms, academia,
extension services, industry associations, and government agencies. Information that a CA uses
does not need to be published in a peer-reviewed journal, although we encourage use of peerreviewed data and information.
Although the types of data or information that a CA should submit in support of its petition for a
variance vary widely depending upon the nature of the request, some examples include:
•
•

Information about the specific, local growing conditions, including crop, climate, soil,
and geographical and environmental conditions of the region relevant to the request;
Information about the processes, procedures, or practices followed in the growing,
harvesting, packing, or storing of covered produce in the region relevant to the request.

4. Process for Requesting a Variance
To request a variance from one or more requirements of subparts A through O of the Produce
Safety Rule, a CA must submit a petition to FDA under the procedures contained in 21 CFR
10.30. (21 CFR 112.172). Subpart P–Variances provides additional specific requirements for a
petition for a variance. We encourage competent authorities considering requesting a variance to
participate in pre-submission consultations with FDA.
A CA could also request that a variance requested by a petition submitted by another competent
authority be applied to its similarly situated persons. (See 21 CFR 112.177). Similarly situated
persons could include, for example, farms that operate under similar circumstances with similar
procedures, processes, and practices as those covered by the other competent authority’s request
for a variance.
We encourage CAs to collaborate with other entities in the development of their petition
requesting a variance, such as industry groups and other relevant stakeholders. These entities
could provide the CA with information to support certain aspects of the variance request or they
could assist the CA in drafting the petition. Additionally, if a CA is requesting a variance for
farms within its jurisdiction that are similarly situated to those covered by a variance requested in
a petition submitted by another CA, the requesting CA could find it useful to access scientific
data and other information from that petition.
We will presume that information submitted in a petition requesting a variance and comments
submitted on such a petition, including a request that a variance be applied to its similarly
situated persons, does not contain information exempt from public disclosure under 21 CFR part
20, and will be made public as part of the docket associated with the request. (21 CFR 112.174).

141

Contains Nonbinding Recommendations
Draft-Not for Implementation

III.

References

We have placed the following references on display in the Dockets Management Staff, Food and
Drug Administration, 5630 Fishers Lane, rm. 1061, Rockville, MD 20852. You may see them at
that location between 9 a.m. and 4 p.m., Monday through Friday. As of July 2018, FDA had
verified the Web site address for the references it makes available as hyperlinks from the Internet
copy of this draft guidance, but FDA is not responsible for any subsequent changes to Non-FDA
Web site references after July 2018.
1. A., Pachepsky Y., D. R. Shelton, J. E. T. McLain, J. Patel, and R.E. Mandrell. 2011.
“Irrigation Waters as a Source of Pathogenic Microorganisms in Produce,” Advances in
Agronomy 113:73-138. doi: 10.1016/b978-0-12-386473-4.00007-5.
2. Ansari, A. A., S.V. Springthorpe, S.A. Sattar, W. Tostowaryk, and G.A. Wells. 1991.
“Comparison of cloth, paper, and warm air drying in eliminating viruses and bacteria
from washed hands,” American Journal of Infectious Control. https://ac.elscdn.com/S0196655305802561/1-s2.0-S0196655305802561-main.pdf?_tid=fb7fc7fa2e2d-4327-bdcebdf94344ac21&acdnat=1531864393_304f7e17ab49fcea62371faa83ed2887.
3. Archer, Douglas L. 2004. “Freezing: an Underutilized Food Safety Technology?”
International Journal of Food Microbiology 90 (2):127-138. https://ac.elscdn.com/S0168160503002150/1-s2.0-S0168160503002150-main.pdf?_tid=9069a7d747cf-41d6-845faf2453b81c86&acdnat=1531864808_c5f1f06ac8c122dc27d60b7483926ce9.
4. Aruscavage, D., S. Miller, M.L. Lewis Ivey, K. Lee, and J.T. LeJeune. 2008. “Physically and
Biologically Damaged Lettuce Plants,” Journal of Food Protection 71 (12):2384-2388.
https://doi.org/10.4315/0362-028X-71.12.2384.
5. Aruscavage, D., K. Lee, S. Miller, and J.T. LeJeune. 2006. “Interactions Affecting the
Proliferation and Control of Human Pathogens on Edible Plants,” Journal of Food
Science 71 (8):R89 - R99. doi: 10.1111/j.1750-3841.2006.00157.x/full.
6. Bagcigil, A.F., S. Ikiz, B. Dokuzeylu, B. Basaran, E. Or, and N.Y. Ozgur. 2007. “Fecal
shedding of Salmonella spp. in dogs,” Journal of Veterinary Medicine Science 69 (7):
775-777. https://www.ncbi.nlm.nih.gov/pubmed/17675814.
7. Becker, B. R., and B.A. Fricke. 1996. “Transpiration and Respiration of Fruits and
Vegetables,” http://b.web.umkc.edu/beckerb/publications/chapters/trans_resp.pdf
8. Beuchat, L. R. 1996. “Pathogenic Microorganisms Associated with Fresh Produce.” Journal
of Food Protection 59 (2):204-216. http://jfoodprotection.org/doi/pdf/10.4315/0362028X-59.2.204?code=fopr-site.
9. Beuchat, L. R. 1999. “Survival of Enterohemorrhagic Escherichia coli O157: H7 in Bovine
Feces Applied to Lettuce and the Effectiveness of Chlorinated Water as a Disinfectant,”
Journal of Food Protection 62 (8):845-849.
http://jfoodprotection.org/doi/pdf/10.4315/0362-028X-62.8.845?code=FOPR-site
10. Beuchat, L. R. 2002. “Ecological Factors Influencing Survival and Growth of Human
Pathogens on Raw Fruits and Vegetables,” Microbes and Infection 4:413-423.
http://www.sciencedirect.com/science/article/pii/S1286457902015551?via%3Dihub.

Contains Nonbinding Recommendations
Draft-Not for Implementation
11. Beuchat, L. R., Komitopoulou, K,. Beckers, H., Betts, R.P., Bourdichon, F. Fanning, S.,
Joosten, H. M., and Ter Kuile, B. H. 2013, “Low-water Activity Foods: Increased
Concern as Vehicles of Foodborne Pathogens,” Journal of Food Protection 76 (1):15072. http://jfoodprotection.org/doi/pdf/10.4315/0362-028X.JFP-12-211.
12. Beuchat, L. R. 2011. “Persistence and Survival of Pathogens in Dry Foods and Dry Food
Processing Environments.” http://ilsi.eu/wp-content/uploads/sites/3/2016/06/Persistenceand-survival-report.pdf
13. Beutin, L., D. Geier, H. Steinrück, S. Zimmermann, and F. Scheutz. 1993. “Prevalence and
some properties of verotoxin (Shiga-like toxin)-producing Escherichia coli in seven
different species of healthy domestic animals,” Journal of Clinical Microbiology 31
(9):2483-2488. https://www.ncbi.nlm.nih.gov/pmc/articles/PMC265781/pdf/jcm000210249.pdf.
14. Bihn, A.E., and Gravani B.R. 2006. Role of Good Agricultural Practices in Fruit and
Vegetable Safety. In Microbiology of Fresh Produce. Washington, DC.
15. Birkenhauer, E, and S. Neethirajan. 2015. “Chapter 4-Prevention and Control of Biofilms in
the Food Industry and Bio-Nanotechnology Approaches In Biofilms in the Food
Environment”, 84. United Kingdom: Wiley Blackwell.
16. Brackett, R. E. 1992. “Shelf Stability and Safety of Fresh Produce as Influenced by
Sanitation and Disinfection,” Journal of Food Protection 55 (10):808-814.
http://jfoodprotection.org/doi/pdf/10.4315/0362-028X-55.10.808?code=fopr-site.
17. Brackett, R. E. 1999. “Incidence, Contributing Factors, and Control of Bacterial Pathogens in
Produce,” Postharvest Biology and Technology 15:305–311.
18. Carpentier, B., and O. Cerf. 1993. “Biofilms and their Consequences, with Particular
Reference to Hygiene in the Food Industry,” Journal of Applied Bacteriology 76:499511.
19. Carpentier, B., and O. Cerf. 2011. “Review--Persistence of Listeria monocytogenes in Food
Industry Equipment and Premises,” Int J Food Microbiol 145 (1):1-8. http://ac.elscdn.com/S0168160511000122/1-s2.0-S0168160511000122-main.pdf?_tid=617977049531-11e6-b8a000000aab0f27&acdnat=1476795180_a46f84b8afc51230447883e4735c60.
20. Carrasco, E., A. Morales-Rueda, and R.M. García-Gimeno. 2011. Cross-contamination and
recontamination by Salmonella in foods: A review,” Food Research International 45
(2):545-556. doi: 10.1016/j.foodres.2011.11.004.
21. Carrington, E. G. 2011. “Evaluation of Sludge Treatments for Pathogen Reduction-Final
Report.” European Commission DG Environment.
22. Cason, J. A., A. Hinton, J. K. Northcutt, R. J. Buhr, D. K. Ingram, D. P. Smith, and N. A.
Cox. 2007. “Partitioning of External and Internal Bacteria Carried by Broiler Chickens
before Processing,” Journal of Food Protection 70 (9):2056-2062.
http://jfoodprotection.org/doi/pdf/10.4315/0362-028X-70.9.2056.
23. CDC. 2012. “Multistate Outbreak of Listeriosis Linked to Whole Cantaloupes from Jensen
Farms, Colorado (Final update).” https://www.cdc.gov/listeria/outbreaks/cantaloupesjensen-farms/index.html.
24. CDC. 2012. “Lesson 1: Principles of Epidemiology. Section 10.”
https://www.cdc.gov/ophss/csels/dsepd/ss1978/lesson1/section10.html
25. CDC. 2015. “Toilets and latrines.”
https://www.cdc.gov/healthywater/global/sanitation/toilets.html.
143

Contains Nonbinding Recommendations
Draft-Not for Implementation
26. CDC. 2017. “Home Canning and Botulism.”
https://www.cdc.gov/features/homecanning/index.html.
27. CDC. 2017. “Symptoms and Sources of Food Poisoning.”
https://www.cdc.gov/foodsafety/symptoms.html.
28. CDC. 2013. “Surveillance of Foodborne Disease Outbreaks - United States, 1998-2008.”
MMWR Surveillance Summaries 62, 1-40.
29. Charbonneau, D. L., J. M. Ponte, and B. A. Kochanowski. 2000. “A Method of Assessing
the Efficacy of Hand Sanitizers: Use of Real Soil Encountered in the Food Service
Industry,” Journal of Food Protection, 63 (4):495–501.
30. Chen, Z., and X. Jiang. 2014. “Microbiological Safety of Chicken Litter or Chicken LitterBased Organic Fertilizers: A Review,” Agriculture 4 (1):1-29. doi:
10.3390/agriculture4010001.
31. Chomel, B., and B. Sun. 2011. “Zoonoses in the Bedroom,” Emerging Infectious Diseases
17 (2):167-172. doi: 10.3201/eid1702.101070.
32. Crowley, C., J. Johanson, M. Mahovic, and S. Trujillo. 2012. Memorandum to the File-FDA
Farm Investigations in Response to Outbreaks and Positive Sampling Findings for Use in
Produce Rule Qualitative Risk Assessment: 2005-2008. In: FDA Farm Investigations in
Response to Outbreaks and Positive Sampling Findings for Use in Produce Rule
Qualitative Risk Assessment.
33. Crump, J. A., A. C. Sulka, A. J. Langer, C. Schaben, A. S. Crielly, R. Gage, M. Baysinger,
M. Moll, G. Withers, D. M. Toney, S. B. Hunter, R. M. Hoekstra, S. K. Wong, P. M.
Griffin, and T. J. Van Gilder. 2002. “An Outbreak of Escherichia coli O157:H7
Infections among Visitors to a Dairy Farm,” New England Journal of Medicine 347
(8):555-560. https://www.nejm.org/doi/10.1056/NEJMoa020524.
34. D'Lima, C., K. Vierk., and Food and Drug Administration. 2011. Memorandum to the File Produce Related Outbreaks and illnesses.
35. Danon, M., I. H. Franke-Whittle, H. Insam, Y. Chen, and Y. Hadar. 2008. “Molecular
analysis of bacterial community succession during prolonged compost curing,” FEMS
Microbiology Ecology 65 (1):133-44. doi: 10.1111/j.1574-6941.2008.00506.x.
36. De Roever, C. D. 1998. “Microbiological Safety Evaluations and Recommendations on Fresh
Produce,” Food Control 9 (6):321-347.
37. Doyle, M. P., and C. M. Erickson. 2011. “Reducing the Carriage of Foodborne Pathogens in
Livestock and Poultry,” 85:960–973.
38. Dunsmore, D. G., A. Twomey, W. G. Whittlestone, and H. W. Morgan. 1981. “Design and
Performance of Systems for Cleaning,” Journal of Food Protection 44 (3):220-240.
39. Dvorak, G. 2008. “Center for Food Security and Public Health 2008 Disinfection 101.”.
40. EPA. 2003. “Control of Pathogens and Vector Attraction in Sewage Sludge In
Environmental Regulations and Technology.”
41. EPA. 2005. “A Homeowner’s Guide to Septic Systems.”
http://nepis.epa.gov/Exe/ZyPDF.cgi/200041E0.PDF?Dockey=200041E0.PDF.
42. EPA. 2012. Case Studies of Individual and Clustered (Decentralized) Wastewater
Management Programs. https://www.epa.gov/sites/production/files/201506/documents/decentralized-case-studies-2012.pdf.
43. EPA. 2013. “Moisture Control Guidance for Building Design, Construction and
Maintenance.” https://www.epa.gov/indoor-air-quality-iaq/moisture-control-guidancebuilding-design-construction-and-maintenance-0.
144

Contains Nonbinding Recommendations
Draft-Not for Implementation
44. EPA. 2016. “Septic Systems Guidance, Policy, and Regulations.”
https://www.epa.gov/septic/how-your-septic-system-works.
45. EPA. 2017. “Septic Systems Overview.” https://www.epa.gov/septic/septic-systemsoverview.
46. Fagernes, M. 2007. “Impact of a Single Plain Finger Ring on the Bacterial Load on the
Hands of Healthcare Workers,” Infection Control and Hospital Epidemiology 28
(10):1191-5.
47. Fagernes, M., and R. Nord. 2007. “A study of microbial load of different types of finger rings
worn by healthcare personnel,” VÅRD I NORDEN 27 (84):21–24.
48. FAO/WHO. 2008. “Microbiological Hazards in Fresh Fruits and Vegetables Meeting
Report.”.
49. FAO/WHO. 2008. “Microbiological Hazards in Fresh Leafy Vegetables and Herbs Meeting
Report.”.
50. Farber, J. N. , L. J. Harris, M. E. Parish, L. R. Beuchat, T. V. Suslow, J.R. Gorney, E. H.
Garrett, and F. F. Busta. 2003. “Microbiological Safety of Controlled and Modified
Atmosphere Packaging of Fresh and Fresh-Cut Produce,” Comprehensive Reviews in
Food Science and Food Safety 2:142-160.
51. FDA. 2011. “Environmental Assessment: Factors Potentially Contributing to the
Contamination of Fresh Whole Cantaloupe Implicated in a Multi-State Outbreak of
Listeriosis.” Last Modified September 20, 2015 Accessed June 19, 2015.
http://www.fda.gov/Food/RecallsOutbreaksEmergencies/Outbreaks/ucm276247.htm.
52. FDA. 2011. “Environmental Assessment: Factors Potentially Contributing to the
Contamination of Fresh Whole Cantaloupe Implicated in a Multi-State Outbreak of
Listeriosis.”. Last Modified September 20, 2015 Accessed June 19, 2015.
http://www.fda.gov/Food/RecallsOutbreaksEmergencies/Outbreaks/ucm276247.htm.
53. FDA. 2013. “Environment Assessment: Factors Potentially Contributing to the
Contamination of Fresh Whole Cantaloupe Implicated in a Multi-State Outbreak of
Salmonellosis.”. http://wayback.archiveit.org/7993/20171114155057/https://www.fda.gov/Food/RecallsOutbreaksEmergencies/
Outbreaks/ucm341476.htm
54. FDA. 2015. “Final Qualitative Assessment of Risk to Public Health from On-Farm
Contamination of Produce.”.
https://www.fda.gov/downloads/Food/FoodScienceResearch/RiskSafetyAssessment/UC
M470780.pdf
55. FDA. 2017. “Food Code 2017.’’ Annex 3 Table 1a, 377.
56. FDA. 2017. “Food Code 2017.” Chapter 1-2 Definitions, 3.
57. Fleming, N., and C. Mills. 1992. “Not Another Inventory, Rather a Catalyst for Reflection.”.
58. Flores, G. E., S. T. Bates, D. Knights, C. L. Lauber, J. Stombaugh, R. Knight, and N. Fierer.
2011. “Microbial Biogeography of Public Restroom Surfaces,” PLoS One 6 (11):e28132.
doi: 10.1371/journal.pone.0028132.
59. Foddai, A. C., I. R. Grant, and M. Dean. 2016. “Efficacy of Instant Hand Sanitizers against
Foodborne Pathogens Compared with Hand Washing with Soap and Water in Food
Preparation Settings: A Systematic Review,” Journal of Food Protection 79 (6):1040-54.
doi: 10.4315/0362-028X.JFP-15-492.

145

Contains Nonbinding Recommendations
Draft-Not for Implementation
60. Gardner, T. J., C.Fitzgerald, C. Xavier, R. Klein, J. Pruckler, S. Stroika, and J. B.
McLaughlin. 2011. “Outbreak of Campylobacteriosis Associated With Consumption of
Raw Peas,” Clinical Infectious Diseases 53 (1):26-32. doi: 10.1093/cid/cir249.
61. Gaukel, V. 2016. “Cooling and Freezing of Foods,” Reference Module in Food Science :1-3
doi: 10.1016/b978-0-08-100596-5.03415-6.
62. Gil, M. I., and M. V., Selma. 2005. “Chapter 6- Overview of Hazards in Fresh-Cut Produce
Production: Control and Management of Food Safety Hazards In Microbial Hazard
Identification in Fresh Fruit and Vegetables. doi:
https://doi.org/10.1002/0470007761.ch6. Hoboken, New Jersey. John Wiley and Sons,
Inc.
63. Gopinath, S., S. Carden, and D. Monack. 2012, “Shedding light on Salmonella Carriers.”
Trends Microbiology 20 (7):320-7.
https://www.sciencedirect.com/science/article/pii/S0966842X12000777.
64. Gravani, R. B. 2010. “Farm Worker Health and Hygiene.” Produce Safety Project Issue
Brief. http://www.pewtrusts.org/~/media/assets/2009/pspworker1pdf.pdf. Accessed 11–
29–2011.
65. Greig, J.D., E.C.D. Todd, C.A. Bartleson, and B.S. Michaels. 2007. “Outbreaks Where Food
Workers Have Been Implicated in the Spread of Foodborne Disease. Part 1. Description
of the Problem, Methods, and Agents Involved,” Journal of Food Protection 70:17521761.
66. Hammons, S. R., A. J. Etter, J. Wang, T. Wu, T. Ford, M. T. Howard, and H. F. Oliver. 2017.
“Evaluation of Third-Party Deep Cleaning as a Listeria monocytogenes Control Strategy
in Retail Delis,” Journal of Food Protection 80 (11):1913 - 1923.
67. Harris, L. J., J. N. Farber, L. R. Beuchat, M. E. Parish, T. V. Suslow, E. H. Garrett, and F. F.
Busta. 2003. “Chapter 3- Outbreaks Associated with Fresh Produce: Incidence, Growth,
and Survival of Pathogens in Fresh and Fresh-Cut Produce,” Comprehensive Reviews in
Food Science and Food Safety 2:78-141.
68. Howard. 2002. “Chapter 4-Excreta Disposal In Healthy Villages: A guide for communities
and community health workers.”
69. Huang, C., W. Ma, and S. Stack. 2012. “The Hygienic Efficacy of Different Hand-drying
methods: a review of the evidence,” Mayo Clinic 87 (8):791-8. doi:
10.1016/j.mayocp.2012.02.019.
70. Hutin , Yvan J.F., V. Pool , E. H. Cramer, O. V. Nainan, J. Weth, I.T. Williams, S. T.
Goldstein, K. F. Gensheimer, B. P. Bell, C. N. Shapiro, M. J. Alter, and H. S. Margolis.
1999. “A Multistate, Foodborne Outbreak of Hepatitis A,” New England Journal of
Medicine 340 (8):595-602. doi: 10.1056/nejm199902253400802.
71. Ingham, S. C., J. A. Losinski, M. P. Andrews, J. E. Breuer, J. R. Breuer, M. T. Wood, and T.
M. Wright. 2004. “Escherichia coli Contamination of Vegetables Grown in Soils
Fertilized with Noncomposted Bovine Manure: Garden-Scale Studies,” Applied and
Environmental Microbiology 70 (11):6420-6427.
72. Ingram, D.T., M.K. Fatica, and M. Mahovic. 2015. “Memorandum to the File : FDA Farm
Investigations in Response to Outbreaks and Positive Sample Findings: 2011-2014.”.
73. Islam, M., M. Doyle, S. C. Phatak, P. Millner, and X. Jiang. 2004. “Persistence of
Enterohemorrhagic Escherichia coli O157:H7 in Soil and on Leaf Lettuce and Parsley
Grown in Fields Treated with Contaminated Manure Composts or Irrigation Water,”
Journal of Food Protection, 67 (7):1365–1370.
146

Contains Nonbinding Recommendations
Draft-Not for Implementation
74. Islam, M., J. Morgan, M. P. Doyle, S. C. Phatak, P. Millner, and X. Jiang. 2004. “Persistence
of Salmonella Enterica Serovar Typhimurium on Lettuce and Parsley in Soils on Which
They Were Grown in Fields Trated with Contaminated Manure Composts Irrigration
Water,” Foodborne Pathogen and Disease 1 (1):27 - 35.
75. Islam, M., M. P. Doyle, S. C. Phatak, P. Millner, and X. Jiang. 2005. “Survival of
Escherichia coli O157:H7 in soil and on carrots and onions grown in fields treated with
contaminated manure composts or irrigation water,” Food Microbiology 22 (1):63-70.
doi: 10.1016/j.fm.2004.04.007.
76. Jay, J. M., M. J. Loessner, and D. A. Golden. 2005. “Chapter 24- Food Poisoning Caused by
Gram-positive Sporeforming Bacteria in Modern Food Microbiology”, 567 – 590. New
York, New York. Springer.
77. Jay, M. T., M. Cooley, D. Carychao, G. W. Wiscomb, R. A. Sweitzer, L. Crawford-Miksza,
J. A. Farrar, D. K. Lau, J. O’Connell, A. Millington, R. V. Asmundson, E. R. Atwill, and
R. E. Mandrell. 2007. “Escherichia coli O157:H7 in Feral Swine near Spinach Fields and
Cattle, Central California Coast,” Emerging Infectious Disease 13 (12):1908-11.
78. Jiang X, and Shepherd M. 2009. “The Role of Manure and Compost in Produce Safety,” In
Microbial Safety of Fresh Produce, edited by Fan X, Niemira BA, Doona CJ, Feeherry
FF and Gravani RB, 143-66. United Kingdom. IFT Press: Wiley-Blackwell.
79. Kaneko, K. I., H. Hayashidani, K. Takahashi, Y. Shiraki, S. Limawongpranee, and M.
Ogawa. 1999. “Bacterial Contamination in the Environment of Food Factories Processing
Ready-to-EatFresh Vegetables,” Journal of Food Protection 62 (7):800–804.
80. Kelley, L. 2013. “Protect Irrigation Equipment From Winter Damage.” Michigan State
University Extension.
http://msue.anr.msu.edu/news/protecting_irrigation_equipment_from_winter_damage.
81. Kennedy, D. I., C. E. Enriquez, and C. P. Gerba. 2010. “Enteric Bacterial Contamination of
Public Restrooms,” CIRIscience:1-12.
82. Kopper, G., S. Mirecki, I. S., Kljujev, V. B., Raicevic, B. T. Lalevic, J. Petrovic-Jovicic, S.
Stojanovski, and D. Blazekovic-Dimovska. 2013. “Chapter 23-Hygiene in Primary
Production in Food Safety Management”, 559-621. Waltham, Massachusetts. Academic
Press.
83. Krysinski, P. E., J. L. Brown, and J. T. Marchisello. 1992. “Effect of Cleaners and Sanitizers
on Listeria monocytogenes Attached to Product Contact surfaces,” Journal of Food
Protection 55 (4):246-251.
84. Kudva, I.T., K. Blanch, and C.J. Hovde. 1998. “Analysis of Escherichia coli O157:H7
Survival in Ovine or Bovine Manure and Manure Slurry,” Applied and Environmental
Microbiology 64 (9):3166–3174.
85. Kwan, L. S. P., C. Xavier, M. Santovenia, J. Pruckler, S. Stroika, K. Joyce, T. Gardner, I. P.
Fields, J. McLaughlin, R. V. Tauxe, and C. Fitzgerald. 2014. “Multilocus sequence
typing confirms wild birds as the source of a camplylobacter outbreak associated with the
consumption of raw peas,” Applied and Environmental Microbiology 80:4540 – 4546.
86. Laidler, M. R., M. Tourdjman, G. L. Buser, T. Hostetler, K. K. Repp, R. Leman, M.
Samadpour, and W. E. Keene. 2013. “Escherichia coli O157:H7 Infections Associated
With Consumption of Locally Grown Strawberries Contaminated by Deer,” Clinical
Infectious Diseases 57 (8):1129-1134. doi: 10.1093/cid/cit468.
87. Larsen, M.H., M. Dalmasso, H. Ingmer, S. Langsrud, M. Malakauskas, A. Mader, T.
Møretrø, S.M. Možina, K. Rychli, M. Wagner, R. J. Wallace, J. Zentek, and K. Jordan.
147

Contains Nonbinding Recommendations
Draft-Not for Implementation
2014. “Persistence of foodborne pathogens and their control in primary and secondary
food production chains,” Food Control 44:92-109. doi: 10.1016/j.foodcont.2014.03.039.
88. Leong, D., A. Alvarez-Ordonez, and K. Jordan. 2014. “Monitoring occurrence and
persistence of Listeria monocytogenes in foods and food processing environments in the
Republic of Ireland,” Front Microbiol 5:436. doi: 10.3389/fmicb.2014.00436.
89. Lin, C. M., F. M. Wu, H. K. Kim, M. P. Doyle, B.S. Michaels, and L. K. Williams. 2003. “A
Comparision of Hand Washing Techniques To Remove Escherichia cali and
Caliciviruses under Natural or Artificial Fingernails,” Journal of Food Protection 66
(12):2296-2301.
90. Lynch, M. F., R. V. Tauxe, and C. W. Hedberg. 2009. “The Growing Burden of Foodborne
Outbreaks Due to Contaminated Fresh Produce: Risks and Opportunities.” Epidemiology
and Infection 137 (3):307-315. doi: 10.1017/S0950268808001969.
91. Lyon, L. J., H. M.; Huff, G. R.; Hooper, S. E.; Telfer, S.D.; Schreiner, and K. J.; Smith.
2000. “Wildland Fire in Ecosystems Effects of Fire on Fauna.” USDA Forest Service
General Technical Report- RMRS-42 (1).
92. Mafu, A. A., Denis, R., J. Goulet, and P. Magny. 1990. “Attachment of Listeria
Monocytogenes to Stainless Steel, Glass, Polypropylene, and Rubber Surfaces After
Short Contact Times,” Journal of Food Protection 53 (9):742-746.
93. Marriott, N., and R. B. Gravani. 2006. “Chapter 10-Sanitizers In Principles of Food
Sanitation”, 165-189. New York, New York. Springer.
94. Marriott, N., and R. B. Gravani. 2006. “Chapter 19- Fruit and Vegetable Processing Plant
Sanitation In Principles of Food Sanitation”, 336-349. New York, New York. Springer.
95. Marriott, N., and R. B. Gravani. 2006. “Chapter 13- Pest Control In Principles of Food
Sanitation”, 235 - 255. New York, New York. Springer.
96. Marriott, N., and R. B. Gravani. 2006. “Chapter 11- Cleaning Compounds In Principles of
Food Sanitation”, 190-212. New York, New York. Springer.
97. Marriott, N., and R. B. Gravani. 2006. “Chapter 9- Cleaning Compounds In Principles of
Food Sanitation”, 141-164. New York, New York. Springer.
98. Meng, J., M. Doyle, T. Zhao, and S. Zhao. 2007. “Enterohemorrhagic Escherichia coli in
Food,” Food Microbiology: Fundamentals and Frontiers:193- 213.
99. Merriweather, S., T. C. Cloyd, C. Robinson, D. Gubernot, and Food and Drug
Administration. 2015. “Memorandum-Produce Related Outbreaks and Illnesses 2011 2014.”.
100. Michaels, B.S., and E.C.D. Todd. 2006. “Chapter 5-Food Worker Personal Hygiene
Requirements During Harvesting, Processing, and Packaging of Plant Products In
Microbial Hazard Identification in Fresh Fruits and Vegetables”, 115-153. Hoboken, NJ.
John Wiley & Sons, Inc.
101. Molloy, K., D. R. Moore, E. Sohoglu, and S. Amitay. 2012. “Less is more: latent learning is
maximized by shorter training sessions in auditory perceptual learning,” PLoS One 7
(5):e36929. doi: 10.1371/journal.pone.0036929.
102. Moore, T.T. 2011. “Climate Change and Animal Migration,” Environmental Law 41:393405.
103. Morato, E. P., L. Leomil, L. Beutin, G. Krause, R. A. Moura, and A. F. Pestana de Castro.
2009. “Domestic Cats Constitute a Natural Reservoir of Human Enteropathogenic
Escherichia coli Types,” Zoonoses & Public Health 56 (5):229-237. doi: 10.1111/j.18632378.2008.01190.x.
148

Contains Nonbinding Recommendations
Draft-Not for Implementation
104. NASPHV. 2011. “Compendium of Measures to Prevent Disease Associated with Animals
in Public Settings.” Recommendations and Reports 60 (4).
105. Natishan, P. M., and W. E. O'Grady. 2014. “Chloride Ion Interactions with Oxide-Covered
Aluminum Leading to Pitting Corrosion: A Review,” Journal of the Electrochemical
Society 161 (9):C421-C432. doi: 10.1149/2.1011409jes.
106. National Environmental Services Center. 2004. “Maintaining your Septic Systems – A
guide for Homeowners,” Pipeline 15(4): 1-8.
107. Nielsen, E. M., M. N. Skov, J. J. Madsen, J. Lodal, J. B. Jespersen, and D. L. Baggesen.
2004. “Verocytotoxin-producing Escherichia coli in wild birds and rodents in close
proximity to farms,” Applied and Environmental Microbiology 70 (11):6944-7. doi:
10.1128/AEM.70.11.6944-6947.2004.
108. Parish, M. E. 1998. “Coliforms, Escherichia coli and Salmonella Serovars Associated with a
Citrus-Processing Facility Implicated in a Salmonellosis Outbreak,” Journal of Food
Protection 61 (3):280-284.
109. Park, Y., Y. Pachepsky, D. Shelton, J. Jeong, and G. Whelan. 2016. “Survival of Manureborne and Fecal Coliforms in Soil: Temperature Dependence as Affected by Site-Specific
Factors,” Journal of Environmental Quality 45 (3):949-57. doi:
10.2134/jeq2015.08.0427.
110. Pell, Alice N. 1997. “Manure and Microbes: Public and Animal Health Problem?” Journal
of Dairy Science 80 (10):2673-2681. doi: http://dx.doi.org/10.3168/jds.S00220302(97)76227-1.
111. Porter, J. D., C. Gaffney, D. Heymann, and W. Parkin. 1990. “Food-borne outbreak of
Giardia lamblia,” American Journal of Public Health 80 (10):1259-1260.
112. QAR. 2015. “Final Qualitative Assessment of Risk to Public Health from On-Farm
Contamination of Produce.”
https://www.fda.gov/downloads/Food/FoodScienceResearch/RiskSafetyAssessment/UC
M470780.pdf.
113. Renter, D. G., and J. M. Sargeant. 2002. “Enterohemorrhagic Escherichia coli O157:
Epidemiology and Ecology in Bovine Production Environments,” Animal Health
Research Reviews 3 (2):83-94. doi: 10.1079/ahrr200245.
114. Salisbury, D., P. Hutfilz, L. Treen, G. Bollin, and S. Gautam. 1997. “The effect of rings on
microbial load of health care workers’ hands,” American Journal of Infectious Control
25:24-27.
115. Scallan, Elaine, Patricia M. Griffin, Frederick J. Angulo, Robert V. Tauxe, and Robert M.
Hoekstra. 2011. “Foodborne Illness Acquired in the United States—Unspecified Agents,”
Emerging Infectious Diseases 17 (1):16-22. doi: 10.3201/eid1701.P21101.
116. Schlegelova, J., V. Babak, M. Holasova, L. Konstantinova, L. Necidova, F. Sisak, H.
Vlokova, P. Roubal, and Z. Jaglic. 2010. “Microbial Contamination after Sanitation of
Food Contact Surfaces in Dairy and Meat Processing Plants,” Czech Journal of Food
Science 28 (5):450-461.
117. Schleh III, F. W., M. P. Lavigne, A. R. Bortolussi, C. A. Allen, E. V. Haldane, A. J. Wort,
W. A. Hightower, E. S. Johnson, H. S. King, S. E. Nicholls, and V. C. Broome. 1983.
“Epidemic Listeriosis Evidence for Transmission by Food,” The New England Journal
of Medicine 308 (4):203-206.
118. Schmidt, H. R., R. V. Lechowich, and J. F. Folinazzo. 1961. “Growth and Toxin Production
by Type E Clostridium Botulinum Below 40°F,” Journal of Food Science 26(6):626-629.
149

Contains Nonbinding Recommendations
Draft-Not for Implementation
119. Silva, D. I., T. R. Careli, C. J. Lima, and J. N. Andrade. 2008. “Effectiveness of Cleaning
and Sanitizing Procedures in Controlling the Adherence of Pseudomonas fluorescens,
Salmonella Enteritidis, and Staphylococcus aureus to domestic kitchen surfaces.”
Ciência e Tecnologia de Alimentos.
120. Silva, E. 2010. “Respiration and Ethylene and their Relationship to Postharvest Handling in
Wholesale Success: a Farmer's Guide to Selling, Postharvest Handling, and Packing
produce (Midwest edition) in Family Farmed. http://www.familyfarmed.org/wpcontent/uploads/2010/07/WSmanual-12pgpreview.pdf
121. Sivapalasingam, S., C. R. Friedman, L. Cohen, and R. V. Tauxe. 2004. “Fresh Produce: A
Growing Cause of Outbreaks of Foodborne Illness in the United States, 1973 through
1997,” Journal of Food Protection, 67 (10):2342–2353.
122. Sivaramalingam, T., D. L. Pearl, S. A. McEwen, D. Ojkic, and M. T. Guerin. 2013. “A
temporal study of Salmonella serovars from fluff samples from poultry breeder hatcheries
in Ontario between 1998 and 2008,” Canadian Journal of Veterinary Research, 77
(1):12–23.
123. Skinner, G. E., and J. W. Larkin. 1998. “Conservative Prediction of Time to Clostridium
botulinum Toxin Formation for Use with Time-Temperature Indicators To Ensure the
Safety of Foods,” Journal of Food Protection 61 (9 ):1154-1160.
124. Soares, V. M., J. G. Pereira, C. Viana, T. B. Izidoro, S. Bersot Ldos, and J. P. Pinto. 2012.
“Transfer of Salmonella Enteritidis to four types of surfaces after cleaning procedures
and cross-contamination to tomatoes,” Food Microbiology 30 (2):453-6. doi:
10.1016/j.fm.2011.12.028.
125. Stanfield, P. 2002. “Chapter 10-Cleaning and Sanitizing a Food Plant In Food Plant
Sanitation”, 101-114. New York, New York. Marcel Dekker, Inc.
126. Stanga, M.. 2010. “Sanitation: Cleaning and Disinfection in the Food Industry”. Italy.
Wiley-VCH.
127. Sugiyama, H., and K.H. Yang. 1975. “Growth Potential of Clostridium botulinum in Fresh
Mushrooms Packaged in Semipermeable Plastic Film,” Applied Microbiology 30
(6):964-969.
128. Tang, J. Y., M. Nishibuchi, Y. Nakaguchi, F. M. Ghazali, A. A. Saleha, and R. Son. 2011.
“Transfer of Campylobacter jejuni from raw to cooked chicken via wood and plastic
cutting boards,” Letters in Applied Microbiology 52 (6):581-8. doi: 10.1111/j.1472765X.2011.03039.x.
129. Taylor, D. J., and A. W. Philbey. 2010. “Salmonella infections in garden birds and cats in a
domestic environment,” Veterinary Record 167 (1):26-7. doi: 10.1136/vr.c3156.
130. Tebbutt, G. M. 2010. “Comparison of traditional and rapid methods for assessing the risk of
bacterial cross-contamination from cutting boards,” International Journal of
Environmental Health Research 9:67-74.
131. Todd, E. C. D., J. D. Greig, C. A. Bartleson, and B.S. Michaels. 2008. “Outbreaks Where
Food Workers Have Been Implicated in the Spread of Foodborne Disease. Part 4.
Infective Doses and Pathogen Carriage,” Journal of Food Protection, 71 (11):2339–
2373.
132. Todd, E.C.D., B.S. Michaels, D. Smith, J.D. Greig, and C.A. Bartleson. 2010. “Outbreaks
Where Food Workers Have Been Implicated in the Spread of Foodborne Disease. Part 9.
Washing and Drying of Hands to Reduce Microbial Contamination,” Journal of Food
Protection 73 (10):1937-1955.
150

Contains Nonbinding Recommendations
Draft-Not for Implementation
133. Todd, E.C.D., M. S. Barry, J. D. Greig, D. Smith, and C. A. Bartleson. 2010. “Outbreaks
where food workers have been implicated in the spread of foodborne disease. Part 8.
Gloves as barriers to prevent contamination of food by workers,” Journal of Food
Protection 73 ( 9 ):1762-1773.
134. Tompkin, R. B., V. N. Scott, D. T. Bernard, W. H. Sveum, and K. S. Gombas. 1999.
“Guidelines to Prevent Post Processing Contamination from Listeria Monocytogenes,”
Dairy, Food and Environmental Sanitation 19 (8):551-562.
135. UAP. “Food manufacturing, processing and storage pest control.” University of Arkansas
publication AG1157. Edited by John D. Hopkins.
136. Watson, A. J., D. Treadwell, A. S. Sargent, K. J. Brecht, and W. Pelletier. 2015.
“Postharvest Storage, Packaging and Handling of Specialty Crops: A Guide for Florida
Small Farm Producers.” IFAS Extension University of Florida.
137. Weil, J. D., C. N. Cutter, R. B. Beelman, and L. F. LaBorde. 2013. “Inactivation of human
pathogens during phase II composting of manure-based mushroom growth substrate,”
Journal of Food Protection 76 (8):1393-400. doi: 10.4315/0362-028X.JFP-12-508.
138. Wheeler, C., T. M. Vogt , G. L. Armstrong, G. Vaughan, A. Weltman, O. V. Nainan,
V.Dato, G. Xia, K. Waller, J. Amon, T. M. Lee, A. Highbaugh-Battle, C. Hembree, S.
Evenson, M. A. Ruta, I. T. Williams, A. E. Fiore, and B. P. Bell. 2005. “An Outbreak of
Hepatitis A Associated with Green Onions,” New England Journal of Medicine 353
(9):890-897. doi: 10.1056/NEJMoa050855.
139. Whipp, S.C. 1994. “Animals as a source of Escherichia coli pathogenic for human-beings.”
Journal of the American Veterinary Medical Association 204 (8):1168-1175.
140. WHO. 2006. “World Health Organization, & United Nations Environmental Programs.
WHO Guidelines for the Safe Use of Wastewater, Excreta and Greywater,” Geneva,
Switzerland. WHO Press.
141. Yan, T., and M. J. Sadowsky. 2007. “Determining Sources of Fecal Bacteria in
Waterways,” Environ Monit Assess 129 (1-3):97-106. doi: 10.1007/s10661-006-9426-z.
142. Yildirim, I., M. Ceyhan, A. B. Cengiz, A. Bagdat, C. Barin, T. Kutluk, and D. Gur. 2008.
“A Prospective Comparative Study of the Relationship between Different Types of Ring
and Microbial Hand Colonization among Pediatric Intensive Care Unit Nurses,”
International Journal of Nursing Studies 45 (11):1572-6. doi:
10.1016/j.ijnurstu.2008.02.010.
143. Zhao, T., M. P. Doyle, J. Shere, and L. Garber. 1995. “Prevalence of enterohemorrhagic
Escherichia coli O157:H7 in a survey of dairy herds,” Applied and Environmental
Microbiology 61 (4):1290-1293.

151


File Typeapplication/pdf
File TitleStandards for the Growing, Harvesting, Packing, and Holding of Produce for Human Consumption: Guidance for Industry
AuthorFDA
File Modified2019-05-23
File Created2018-10-15

© 2024 OMB.report | Privacy Policy